Question about Mahindra Cars & Trucks
There no mark I need diagram to help me and I try to do it old way it donot work
Posted on Nov 26, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: toyota hilux 1984 timing
looking at the gears the upper one is on the gear its a dot. it goes flush with the valve cover mating surface to the right. gear on the right lower has a line and it goes pointed up with a mark on the block. crank gear has a v grove and an arrow on the block just under idler adj good luck man mark as fixed thanks
Posted on Sep 20, 2008
isusu engine?? have you looked for a 8mm hole in timing gear that corresponds with a hole on plate behind then lock it in with a bolt ,remove bolt after tightening belt .DONT FORGET THIS ???.....if you cant find anything do it with no timing marks easy --- piston no 1 at tdc valves closed spin pump till fuel comes out of no 1 injector feed and lock it all together,indirect diesel is 6/8 ,,,,,direct injection is 12/16,,,,and turbo is 18/22 btdc
Posted on Dec 13, 2008
SOURCE: geo metro timing diagram
woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck
Posted on Jan 29, 2009
malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.
Posted on May 06, 2009
Tips for a great answer:
Nov 01, 2015 | Mahindra Cars & Trucks
Apr 29, 2015 | Mahindra Cars & Trucks
Nov 24, 2014 | Mahindra Bolero Cars & Trucks
Aug 06, 2014 | Mahindra Scorpio Cars & Trucks
Apr 07, 2014 | 2007 Mahindra Bolero NEF
Apr 15, 2013 | 2011 Mahindra Scorpio
Sep 27, 2012 | 2011 Mahindra Scorpio
Feb 19, 2012 | 2006 Mahindra Bolero Single
603 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: