Question about Cars & Trucks

1 Answer

I have a 2001 s10 pick up 2 wheel drive 5 speed and I put new bake pads,rotors and calipers and after bleeding them there still is no brakes and they are grinding really bad what is th cause now?

Posted by on

Ad

1 Answer

No idea -- because I have no idea how
you do your brake work or what you did,
until you explain it

No reason for any grinding, if your put it
together correctly

I have never in 50 years had or seen where
you could assemble brakes wrong,if you can,
then you don't work on vehicles

No brakes,how so,if the rotors,pads & calipers went on,
as they came off & they side nice before you bleed the
system,then they were not bleed correctly

Posted on Nov 25, 2014

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jgwhomeequip
  • 1902 Answers

SOURCE: no brakes after changing brake caliper & bleeding system

Sounds like you still have air in your brake lines. Make sure all your brake lines are tight. Then bleed again. Bleed the trouble side first, meaning right side, then go to front left, back left then back right, make sure that your brake fluid is also full

Posted on Feb 11, 2009

keithheavili
  • 410 Answers

SOURCE: New brakes still making grinding noise

Sounds like it is your hub bearings.  Jack the car up and check for play in the hub bearings.  More than likely this is your issue and the bearings need to be replaced.  Hope this helps.  Thanks for an honest rating.

Posted on May 19, 2009

keithheavili
  • 410 Answers

SOURCE: 2004 Saturn VUE AWD V6 has a harsh grinding sound in front wheels

Have you checked your wheel bearings? When these go out you can get a harsh grinding noise. This sounds like that is what it might be. Does it happen when you are going fast/slow turning/going straight? I know you said it's inconsistent but the more info the better. However, if I had to bet, based on what you have already said, it's your wheel bearings. Let me know if you have further questions. Thanks for using FixYa!

Posted on Aug 01, 2009

  • 635 Answers

SOURCE: Spongy brakes

So long as the brake booster is working, test it by turning on the engine, press the brake pedal all the way down, then shut off engine keeping your foot on the brake pedal, if the pedal comes up slightly pushing against your foot then the booster IS working.

Did you BLEED the brakes??????

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front brake pads


1. Raise vehicle
2. Support on jack stand
3. Remove lug nuts
4. Remove wheel
5. Remove bolts holding caliper
6. Remove calipers
7. Remove brake pads
8. Push piston into caliper
9. Inspection rotor for damage if damaged replace
10. Install new pads
11a. Replace caliper on rotor
11 b. Replace bolts in caliper and tighten
12. Bleed brakes
13. Replace wheel
14. Replace lug nuts
15. Lower vehicle
16. Tighten lug nuts
17. Test drive vehicle

Oct 17, 2015 | 2004 Chrysler Sebring

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

How to replace rear brake pads on 2002 buick rendevous


Those are special calipers. The piston cannot be just compressed back into the caliper - it needs to be turned as it is compressed or you can ruin the caliper.There is a kit you can rent from AutoZone or many independent auto parts stores that will perform both functions at the same time.
Block fron wheels and raise vehicle passenger side. Remove wheel. The caliper is on the top rear side of the assembly you're looking at.There are 2 long bolts you'll need to remove to take the caliper off the vehicle. Don't remove the brake line or open the bleeder screw ( either of these moves will add to your work!! ) Insert a large flat blade screwdriver in between the rotor and outboard brake pad and pry away from the vehicle slightly to release the pads from the rotor. Slide caliper upwards and towards the back of the vehicle to separate from rotor. The pads will come in a full set ( all 4 pads for both side of the rear ) . Look at your replacement pads and determine if they have a retainer clip holding them in place or a compression clip. Remove outboard pad first then inboard. Match old pads to replacement pads. Inspect rotor for grooves and irregular surfaces - if any grooves or irregularity present, remove rotor and take to an auto parts store for refinishing.Compress caliper piston with kit and allow 5 minutes for pressure to bleed back into the master cylinder.install rotor if removed and wipe surfaces with brake clean. Install inboard then outboard pad and place caliper on rotor, then mount to vehicle. Install wheel, repeat procedure for drivers side, then PUMP BRAKE PEDAL 5 TIMES BEFORE TRYING TO DRIVE VEHICLE to set pads on rotors.

Nov 26, 2010 | 2003 Buick Rendezvous

1 Answer

I have a 2001 BMW 318I, E46 MODEL , HOW DO YOU FIT BRAKE PADS TO FRONT AND REAR, THANKS TREVOR.


YOU NEED A PISTON COMPRESS TOOL TO PRESS PISTON BACK IN THE BORE WITH THE BLEEDER SCREW OPEN ON THE CALIPER*.CLOSE BLEEDER SCREW JUST BEFORE THE CALIPER PISTON IS PUSHED FULLY INTO CALIPER.THIS WILL ALLOW ROOM FOR NEW BRAKE PADS AND CALIPER FIT OVER THE BRAKE ROTOR.WHEN FINISH.PUTTING BRAKE PADS ON YOU HAVE TO BLEED BRAKE SYSTEM.DONT DRIVE VECHICLE IF YOU CANT GET A GOOD FIRM BRAKES.

Oct 15, 2010 | BMW 318 Cars & Trucks

1 Answer

Replace disc pads procudure


They are actually pretty simple, but check or replace the rotors before you install new pads. The front discs have 2 bolts per caliper as do the rears. There are hardware clips that are different on the front and rear.

You unbolt the caliper and tie it up with a rope or coat hanger so the caliper does not hang by the brake hose. Service the rotors and then when you are ready to replace the caliper, you take off the master cylinder cover. Then you use a "C" clamp to drive the caliper piston flush into the caliper. Doing this will force Brake fluid back into the Master cylinder. This is why the Master cylinder cap must be off. Attach the brake pads with a chemical to eliminate rattles and then slide the loaded caliper over the rotor. Attach the 2 bolts on the caliper and then you are ready to bleed the system.

Repeat this on each wheel and then bleed all 4 wheels. There will be very little air in the system using this method. The back brakes have the E-Brakes inside the rotors. If you pull off the rear rotors you will have to loosen the E-brakes by turning the Starwheel inside the rotor to allow for more clearance. Adjust the same Starwheels by tightening until independent wheel drags substantially, then loosen up 5 or more clicks on the Starwheel.

The calipers will take care of themselves and center themselves through use. Thats about all I can say about this process. I hope this helps you.

Aug 28, 2010 | 2001 Mercury Grand Marquis

1 Answer

Need to know how to change brakes rotors and calibers on 1996 gmc jimmy


Hi Friend:

#1) Break Loose your Lug Nuts,Just A Little don't Take-them off yet.

#2) Jack Front end off the Ground,Support with Good jack stands,Keep Truck in Park and Emergency brake Applied.

#3) Now Take off your Front Wheels-Tires.

#4) Now on the Inside of your brake rotor on each side,there are 2-Caliper mounting bolts. Allen Bolts 3/8" Allen Socket or Allen Wrench.Break the 2-Bolts loose and Remove them.

#5) Now after the Caliper Bolts are removed ,Loosen the Brake Line going to the Calipers using a Flare wrench.You'll need to have a Drain Pan handy to Catch the Brake Fluid.

#6) Now you'll need a C Clamp ,to compress the caliper piston back in the Caliper. NOTE: before you compress the Caliper pistons ,take off the master cylinder cover and using a suction bulb remove about 1/2 of the fluid from the Front Resevoir.the larger of the two.

#7) Now placing the C-Clamp over the Caliper housing turn it clockwise to compress the Piston all the way in.

#8) now you can remove your caliper and the pads,same for Both Sides. AND remove your Rotors they are held on by the Calipers and your Lug-Nuts.It Should come right off ,if its a little rusted and Stubborn take a Plastic Headed Hammer and Tap it all around the Old Rotor.Until it comes off.

#9) Now Slide your new Rotors on the HUB and over the lug nuts.

#10) Get your new caliper Making sure you have the Correct Caliper its Marked Left or Right Sides. It will only work on the Side its made for.

#11) Now put your Anti Rattel Clips on the Correct Sides(Inside) that fit into the New Caiper Piston.also use some brake lube on the back on the new brake pads where they touch the caiper housing.

#12) With both pads in the Caliper Slide the Caliper over your New Rotor. This is for both sides.

#13) Put your brake line back on using the new brass washers that came with your rotors/or Caipers.

#14) Now Put your Caliper Mounting bolts in and tighten up to 38 Foot Lbs.

#15) When you have both sides done Fill up your master Cylinder about a 1/4 " from top.

16) Now you'll need to bleed them ,Get a Friend and have them Slowly push the brake pedal down,after he says its down you open the bleeder valve until fluid and air come out==Now tighten it back before your friend raises his foot up off the pedal.During bleeding keep checking your Master Cylinder to keep it full of fluid.

#17) Start your bleeding from the Right Rear to Left Rear to Right Front and Last Left Front. Always bleed from the farthest brake or Wheel from the Master Cylinder and work your way to the Master.

#18) After you have No air coming out of the bleeder valve and you do have good clean brake fluid.Your Done Bleeding;You should have a Good tight and High Brake Pedal. NOTE: you DON't start the Truck to bleed the brakes.

#19) Now just Put your Tires back on and Tighten your Lug Nuts and you should have good Brakes.

I'm sure that this will get you good brakes and on the Road Again.

Thanks for Using Fixya Please let me know How my Solution Helped you by Voting For the Quality of my help.

Thanks Again: From: d_hubbs

Aug 27, 2010 | GMC Jimmy Cars & Trucks

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

All new brake shoes on 97 jeep front callibers still sticking


The problem lays with the Caliper itself and/or the brake hose connected to the Caliper.
However if you replaced the pads, did you also replace the Rotors or have them Turned? The old pads wear the rotor. New pads on old rotors that have not been replaced or turned may end with rubbing or stuck brakes.
A simple way to test whether it's one and/or the other:
1. Remove the Caliper from the rotor, remove the pads. Keep for now the caliper attached to the brake hose.
2. Very slowly push on the brake, exposing more of the piston out of the bore. Not all the way. Usually until the rubber dust seal/boot is fully extended.
3. Check the seal/boot for cracks and tears, and if clean or not. Bad seals may prevent the piston from re-seating.
4. Using a c-clamp and pushing straight in: Try repushing the Caliper Piston back into the Caliper Bore (the cup back into the hole). It should go back in realitively easy.
5. If it doesn't go back in easy: Again slowly pump the brake and re-push the pistons back out to full extended seal/boot (but not the piston out of the bore).
6. Detached the brake hose from the caliper.
7. Again using a c-clamp and pushing straight in: Try again to repush the caliper piston back into the bore without the hose attached. If it goes back-in relatively easy - the caliper is okay...it is the brake hose.
8. If the caliper piston does not go back in easily - Replace the caliper.
9. When Installing the new (reman) caliper, remember to bleed the brakes.
TRY EITHER OR #10 OR #11 BELOW:
After the new Caliper is reattached to hose and has been bled:
10. Again push on the brake petal to fully extend the caliper piston fully (rubber seal/boot fully extended) Again do not push the piston out of the bore! Try pushing the piston back into the bore. If it does not re-seat relatively easy: Replace the brake hose.
11. Another method: After replacing the new caliper back on the rotor: Assumng the entire front end (2WD front wheel drive) or entire vehicle (2WD rear wheel drive) or (4WD all the time) is jacked up off the ground
a. Put the lug nuts back on the rotor.
b. Have helper Start the vehicle and place in Drive. Don't step on gas!
c. Have then let off the brake and then engage the brake.
d. When they let off the brake watch to see if the Rotor is turning or not, if rubbing or not. Or if still sticking.
e. With a new caliper, turned or new rotors, and still a problem? It is the brake hose!
12. Replace the brake hose and try again.

Another method but more expensive:
OR Replace the calipers, brake hoses; bleed and test!

If this helped or not; or if you need additional help or have addtional questions let me know on fixya.com!

Nov 28, 2009 | 1997 Jeep Grand Cherokee

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...