Question about 2003 Kia Spectra

1 Answer

I went to look too see how too replace the altinator belt and then when i started taking the bolts off I found out was their was no bult in the bottom of the altinator all I wanted to know is if the BOLt ON TOP IS THE Same as the Bottom ( altinator 2003 kia spectra)

Posted by on

Ad

1 Answer

Now we get the picture

Go to a Dealers Parts Dept with your
vehicle VIN # & order the missing bolt

Posted on Nov 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 65 Answers

SOURCE: I want to replace the

You will have to remove the rear seat.Go to the bottom cusion in the front and yank it up,about a foot in from the outside on each side.Once it out there are some bolts on the bottom of the back rest cusion remove those and push it up and remove.Then you cen get to three nuts on each strut top.

Posted on Nov 29, 2008

  • 8 Answers

SOURCE: changing rear brake pads on 2002 buick lesabre

Your correct, does hinge on top bolt and then is ussually stiff pulling from pin, but it will move

Posted on Jul 01, 2009

  • 233 Answers

SOURCE: VW passat 2002 tdi- Alternator

you have to lift engine a bit to make clearance. take engine mounts loose or contact vw dealer and talk to one of there techs

Posted on Dec 28, 2010

ghost45
  • 1280 Answers

SOURCE: how do i remove a power steering pump on my 2003

I presume your Santa Fe sports the 3.5 liter V6 engine? If it's got the NUT, it's at the front & there's a nut stud. If it's got the BOLT, it's accessed from the opposite (anterior) side using a long, long extension. If you have a vehicle hoist/lift, you can easily see it. If you're on your back with the vehicle on jack stands, it's much more difficult to see the 14mm bolt between the exhaust flex pipe and heat shield of the exhaust manifold at the right hand side of the engine.
Say you're directly beneath the engine oil pan, move toward the transmission and look upward and forward between the 1:00 and 2:00 oclock positions of the engine (toward the power steering pump) - 14mm bolt

Posted on Feb 08, 2011

heimlich
  • 1978 Answers

SOURCE: I am trying to change

BEFORE ADJUSTING THE ALTERNATOR BELT DISCONNECT THE NEGATIVE BATTERY CABLE OR YOU MIGHT BLOW AN EXPENSIVE HIDDEN FUSE.
I would replace the steering pump belt at the same time you do the alternator belt (buy both).
To take off the alternator belt .
First , take off the negative battery cable so you do not blow an expensive fuse on the positive battery cable clamp(or a block fuse under the hood). Facing the back of the automobile , reach UNDER the alternator and loosen the bolt on the bottom right side, now loosen the bolt on the adjuster block on top, you can now turn the adjuster bolt and move the alternator to change the belt.
To take off the steering pump belt on the front of the motor, you need to loosen the nut on the back side of the pulley (right side of pump mount), the nut holds the adjuster pulley in place . With the adjuster pulley nut loose , you can use the adjuster bolt to move the pulley to adjust/take off the steering pump belt.

Posted on Jun 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace fan belt on 1983 Chevy pickup


Depends on which belt..if it's the alternator belt, out's just a matter of loosening 2 bolts on alternator, sliding alternator towards center of engine and removing belt. Installation is the reverse.

Mar 28, 2011 | 1979 Chevrolet C/K 3500

1 Answer

1998 ford escort altinator two bolt or three bolt? engine light is on brand new battery and the battery light is on . car just died when driving waited 7mins and it started .is it the altinator


check with volt meter. 12 volts with engine off. Should be 14 volts with engine running if alternator is working.
First, clean battery posts and cable ends. Then check owner manual for fuse locations and blown fuses. There is a large 100 amp fuse in box under hood.

Is the battery lamp lit on the dash?

Looks like 3 bolts. please rate when done

SECTION 414-02: Generator and Regulator 1998 Escort/Tracer Workshop Manual
REMOVAL AND INSTALLATION Generator -Sedan and Wagon Removal
  1. Disconnect the battery ground cable.
  1. Remove the generator drive belt.
    1. Release the tension on the drive belt.
    1. Remove the drive belt from the generator pulley.
  1. Disconnect the HO2 sensor harness clip from the generator bracket.

  1. Position the generator bracket aside.
    1. Remove the A/C line bracket bolt.
    1. Remove the power steering pressure line bracket bolts.
    1. Remove the generator bracket bolts.
    1. Position the generator bracket aside.
  1. Remove the generator bolts and position the generator aside.
  1. Remove the generator.
    1. Disconnect the two generator electrical connectors.
    1. Remove the battery positive nut and washer.
    1. Disconnect the battery positive cable and remove the generator.
step 4
snorkelbobby_37.gif

Feb 12, 2011 | 1998 Ford Escort

1 Answer

I need a Diagram on how to install the altinator


There is no diagram. You un-plug/unbolt the wires, unbolt the alternator and remove it. You bolt the new one in, tension the belt and attach the wires. Presto ... you are done. Should take about one hour start to finish.

Feb 04, 2011 | 1995 Nissan Pickup

1 Answer

I want to know were is the adjustor to replaced the altinator belt is hiding


found it7cc0ea6.gif
  1. Disconnect the negative battery cable.
  2. Loosen mounting bolts (A) and (B) from the back side of the alternator.
  3. Adjust bolt (C) until belt tension is 22 ft. lbs. (30 Nm) when measured at deflection point shown.
  4. Retighten locknut (A) to 16 ft. lbs. (22 Nm) and locknut (B) to 32 ft. lbs. (43 Nm).
  5. Connect the negative battery cable.

Sep 25, 2010 | 2000 Kia Sportage

1 Answer

How do i take out my alternator in 1989 crown vick ok i just found out my alternator is killn my battery so i would like to know how can i take the old one out and replace it with a new one


disconnect battery disconnect connector to altinator disconnect battery connection on altinator loosen serpenten belt from altinator loosen bolts and remove old altinator install new altinator and work back to start of unistalling

Sep 15, 2010 | 1989 Ford LTD

2 Answers

How do i change a fan belt on an 1985 escort


fan belt problem lossen nut unberneath altinator and the curved tensionioer you'll see it on the front loosen back bolt on the alinator this should free up the whole unit and it will slacken off and drop down this frees the belt when fitting new belt slip a long screwdriver between altinator and block this gives the tension on the belt BUT DO NOT over tension just enough to squeese the belt together need more help I have a 1600 ghia 85 and workshop manual

Apr 07, 2010 | 1985 Ford Escort 1985 4 Door

1 Answer

I just replace my alternator and the belt isnt tight enough where can i find the belt tensioner bolt


you need to remove the passenger front wheel. remove the plastic cover to expose the tensioner/idler pulley, loosen do not remove the pulley nut i believe its a 14mm socket. then underneath the backside of the pulley, right above the oil filter there is another 14mm bolt. that lower bult is your adjustment, tension as needed :)

Jan 28, 2010 | 1997 Mitsubishi Diamante

2 Answers

Aloud squeal.


You need to tighten the altinator belt..
It squeels and falls off because it is too loose..
Losten the two bolt a bit on the altinator so it will move..
Put the belt on - loose is ok right now..
Use a very large scewdriver or a crowbar - find leverage - to push on the altinator in the derection that tightens the belt..
Once you have some good force on it - keep the force on it as you tighten the bolts..

This will take care of the problem.. ;o)

Note;
We are helping people here every day on a points system.
If the information provided here was at all helpful,
please be kind and rate well and close the post.
Thank you – and enjoy your day ;o)

Jul 31, 2009 | 2001 Kia Sephia

1 Answer

How do I remove my altinator on my 1998 Mazda Millenia?


usally there are only two to 4 bolts the belt and wire first start with removing or loosing the belt then pull out the wires and take out nthe bolts and you should be good

Jul 08, 2009 | 1997 Mazda Millenia

3 Answers

Alternator belt replacement 91 Mazda 323


what is the part number of the fan belt and alternator belt of the madza 232 famila

Mar 17, 2009 | 1991 Mazda 323

Not finding what you are looking for?
2003 Kia Spectra Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...