Question about Cars & Trucks

1 Answer

1995 Chrysler intrepid signal lights not work ing where is the flash er unit? Or what else would cause all 4 not to work? 4 way don't work either? Thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 64 Answers

Sounds like a bad turn signal switch or blown fuse

Posted on Nov 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2001 intrepid signals and flashers not working

I have the same problem right now. When it is 70+ degrees outside my car's windows will not roll down, the AC stops working, and the turn signals will not work. I've been digging into it and it is more than likely a relay.

I'm looking for a service manual with electronic troubleshooting manual online. If you search for it you can find it in a .pdf form. By using the ETM and a multimeter (cheap to buy at SEARS) then you should be able to get your problem out of the way.

Posted on Apr 21, 2009

collegetutor
  • 125 Answers

SOURCE: no hazard lights no signal lights I have

Hello, when this situation happens, you need to do a little extra troubleshooting with the electrical wiring to pinpoint the problem. First, obtain a 12V test light. You can find them at some 99 cent stores or for about $10 from an auto parts store. Probe the hot side of the fuse box terminal and make sure voltage is reaching the circuit there. If not, you know you have a wiring problem and you just have to trace the wire back, normally by the color to the wiring harness and then check again there with the test light for 12V voltage. You might need to get a wiring diagram. Often libraries have donated Chiltons manuals that you can copy the diagram from. I hope this helps get you started. Now, if you have 12V to the fuse, you need to check if you have any voltage to the light bulb that is not working and then work back on the wire from there until you locate the stretch of wire where there is no voltage and then replace that segment or look for the short to ground in that area.

Posted on Sep 22, 2009

  • 277 Answers

SOURCE: 1999 corvette. rear lights do not work at all.

There is a Rear end disconnection of the Wiring harness, most likely in the Trunk.
Regards, David

Posted on Nov 29, 2010

bbl242003
  • 1637 Answers

SOURCE: My 1995 GMC Forward,Signal lights blow fuse,4 way

a door in the back of the glove box (left side) It is in there 2. You can change this out yourself

Posted on Jan 30, 2011

  • 2841 Answers

SOURCE: i don't know where the

Your vehicle has 2 flasher relays. One for the turn signals and one for the hazard lights. The turn signal flasher relay is located on the drivers side, under the dash, mounted on the drivers (Left) side of the steering column. The hazard flasher is mounted on top of the steering column. Do not get them mixed up.

Posted on Aug 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My horn and lights wont stop honking and flashing


Probly the factory alarm or aftermarket unit.

Dec 25, 2012 | 1995 Chrysler Cirrus LXi

1 Answer

Signals not flashing on a 2007 pontiac wave


It can be issue with flasher unit causing the problem:---

To troubleshoot the issue go through the solved help links mentioned below:-----
Click the link :----

Turn Signal Not working

http://technoanswers.blogspot.com/2012/11/turn-signal-not-working.html

-----------

Right turn signal not working on Pontiac Car?

http://schematicsdiagram.blogspot.com/2011/12/right-turn-signal-not-working-on.html

------------

SOLVE YOUR 4 WAY FLASHER RELATED PROBLEMS HERE

http://repairhelpcenter.blogspot.com/2012/11/4-way-flasherturn-signal-flashersignal.html

----------

These details will help.

Thanks.

Dec 05, 2012 | 1995 Plymouth Acclaim

1 Answer

A/c has freon, changed low/high cutoff switch, Compressor only comes on if I jumper directly to + side of battery, Compressor then cools so compressor clutch works. No power at connector to compressor....


first try swapping out the relay. The relay is usually in the box under the hood. If that doesn't work, interrogate the relay socket with a test light to see if the ground signal is coming in from the computer. To do that, connect your test light clip to battery positive and probe the relay socket. If you don't get a bright light with the car running and the A/C turned on, the problem is with the control system. If you have the automatic climate controls, the problem may be in the BCM. I have pasted diagrams for both manual and automatic system below.

jturcotte_2365.gif


jturcotte_2366.gif


jturcotte_2367.gif

Oct 05, 2011 | 1995 Dodge Intrepid

1 Answer

1995 chrysler radio with cassette just stops working will come once in awhile


Check ALL fuses. Check the wires on the back of the unit, especially ground and "key on" wire. It may be an Intermittant shorting of the units ground wire, which would cause the unit to totally shut off and on whenever the short happens. Shouldn't be a hot power wire shorting, because it would have blown the fuse and wouldn't work at all. There is a 12v signal wire that tells the unit when your key is in the on position or the acc. position. The "key on" wire. That wire may be causing the unit to turn itself off and on if it is getting an improper signal. it may also be a problem with the cassette player itself.

Sep 20, 2011 | 1995 Dodge Caravan

2 Answers

Signal lights are not working,can you show me in a diagram where the flasher is located on a 1996 intrepid?


The turn signal/hazzard flasher is a small unit ( little black box, 5 prongs ) Located between the fuse box and brake peddle on a braket under the drivers side air conditioning duct. At some point and time in 1995 dodge swiched over in the middle of production so some 95 intrepid and 96 and 97 should all be the same.
ep27

Feb 14, 2011 | 1996 Dodge Intrepid

1 Answer

Signal/Hazard lights won't work


Most common cause is the Flasher Unit. It's a plug in module usually located under the dash attached to the fuse panel (may need to unscrew a wingnut to drop down fuse panel). Other cause could be burned out bulb but if you are not getting left or right directionals, it's much more likely that it's the Flasher Unit.

Apr 27, 2010 | 1996 Dodge Intrepid

2 Answers

No hazard lights no signal lights I have changed fuses and flasher The car is a 1995 chrysler intrepid v6 with an automatic transmission


Hello, when this situation happens, you need to do a little extra troubleshooting with the electrical wiring to pinpoint the problem. First, obtain a 12V test light. You can find them at some 99 cent stores or for about $10 from an auto parts store. Probe the hot side of the fuse box terminal and make sure voltage is reaching the circuit there. If not, you know you have a wiring problem and you just have to trace the wire back, normally by the color to the wiring harness and then check again there with the test light for 12V voltage. You might need to get a wiring diagram. Often libraries have donated Chiltons manuals that you can copy the diagram from. I hope this helps get you started. Now, if you have 12V to the fuse, you need to check if you have any voltage to the light bulb that is not working and then work back on the wire from there until you locate the stretch of wire where there is no voltage and then replace that segment or look for the short to ground in that area.

Sep 22, 2009 | 1995 Dodge Intrepid

1 Answer

1996 Dodge Intrepid Wiring Schematics for the signal light - Signal lights and wipers do not work and I bought the part (switch) and it still does not work.


check for bad flasher, or lost ground. if not pull the entire light assembly off the vehicle and there is a clipped in plastic plate in the back of the rear assembly that houses the bulbs. this plate has metal bars that run thorough the inside of it to control the individual bulbs..IE some work, others dont. what happens is the plastic plate gets too hot and disloges the bars, or causes corrosion and bingo no lights. the plates are a common problem for the chrysler mid size cars, mostly the taillight assembly. hope I helped

Sep 11, 2009 | 1996 Dodge Intrepid

1 Answer

Signal Lights and hazard lights don't work.


Try lower or under the dash on drivers side, in with fuses.

Nov 10, 2008 | 1995 Chrysler New Yorker

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...