Question about Cars & Trucks

1 Answer

I have 340watts 6.3u 220volt rpm 2300 slot 24 Running coil pitch 8-10-12 swg -27 Starting coil pitch 8-10-12 swg 30, 30 Please send winding diagram

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,506 Answers

Contact the manufacturer of whatever model you have beause no one can help without knwing what make ect you have.

Posted on Nov 27, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 167 Answers

SOURCE: Have 93 Chevy G 30 HAve a High pitch whine that

This could be anything from the pump in the transmission to the alternator bearings/bushings to the power steering pump. Could be an idler pulley bearing, but I doubt it.
Hint: If the noise is very high-pitched, check the alternator. If it is a lower, medium-high-pitch sound that changes some when you turn the wheels, check the power steering pump. If it is almost like a moan or a "Whooo" sound, that's the transmission pump.

Posted on Feb 23, 2010

SOURCE: High pitch winding noise on cold start up.

Sounds like a constricted IAC Idle air control valve passsage. Fairly simple to fix. Remove air filter trunking all the way to the throttle body to allow access. The IAC allows air passed the throttle when closed at idle. Just on the inside of the throttle body in front of the throttle flap there is an opening in the throttle wall. This is the air inlet to the IAC; there is an outlet similar on the other side of the throttle. Use carb cleaner and cloth to shift the grime from this tubing and get it like new. Hold the throttle flap open to get at both ends of the IAC tubing. The IAC can be detached and cleaned to a shine. Reinstall the IAC and replace all air pipe ducting. Leave for about 20 minutes to allow any cleaner residue to dry out. When you restart you might experience a bit of uneven running but this will disappear very quickly as the last of the cleaner dries out

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause a winding noise in the engine from starting engine, during driving, and does not stop winding until it's turned off?


That could be any number of things but I would suspect that the bearings are going in one of the pulleys driven by the fan belt.

Feb 21, 2015 | Cars & Trucks

1 Answer

Need torque specs on axle nuts for dana 50 rear axle


Dana 50 Front Axle

Observe the following torques;

* Left and Right drive axles-to-cross member: 120-150 ft. lbs. (163-203 Nm)

* Axle arm-to-radius arm: 180-240 ft. lbs. (244-325 Nm)

* Coil spring insulator: 30-70 ft. lbs. (41-95 Nm)

* Upper spring retainer: 13-18 ft. lbs. (18-24 Nm)

-----------------------------------------------

Dana 60 Front Axle

Observe the following torques;

* Drive shaft-to-flange: 15-20 ft. lbs. (20-27 Nm)

* Track bar nut and bolt: 160-200 ft. lbs. (217-271 Nm)

* Stabilizer link nut: 20-30 ft. lbs. (27-41 Nm)

* Stabilizer barU-bolt: 50-65 ft. lbs. (68-88 Nm)

* Spindle connecting rod-to-knuckle: 70-100 ft. lbs. (95-136 Nm)

* Front spring U-bolt: 95-100 ft. lbs. (115-135)

Feb 19, 2011 | 1986 Ford F 250

1 Answer

Where do i find a fuse box diagram for a 1994 Grand Cherokee Laredo?


There are 2 fuse blocks. The Power Distribution Center is under the hood along the passenger side fender and has fuses and relays in it. The other is on the passenger side of the dash and has fuses and circuit breakers.
....1994 Jeep Grand Cherokee Laredo
...(Fuse Block - Passenger side of Dash)
.....1........5........9........13........17........21........25
.20 A...15 A...20 A...20 A....7.5 A....15 A....30 A
.....2........6.......10.......14........18........22........26
.15 A...15 A...10 A...20 A.... 15 A....15 A....30 A
.....3........7.......11.......15........19........23........27
.20 A...15 A...15 A....3 A......15 A....15 A....10 A
.....4........8.......12.......16........20........24........28
.15 A...15 A...15 A...20 A.....10 A...7.5 A....30 A
1)Trailer Tow Relay
2)Brake Lamps
3)Hazard Lamps
4)Security Lamp
5)Interior Lighting
6)Security Alarm Module
7)Security Alarm Relay, Security Alarm Module, Flash-to-Pass
8)Overhead Console, Keyless Entry, Radio Memory/Clock
Memory/Chime Module, Power Locks, Power Mirrors,
HEVAC and VIC
9)Rear Wiper
10)Radio
11)Cigar Lighter
12)Parking Lamps, Automatic Headlamps
13)Horn Relay
14)Power Lock Relays
15)ABS Module and Relay
16)Turn Signals
17)Heating and Air Conditioning Module
18)Airbag Module
19)Interior Mirror, Auto Headlamps, Overhead Console,
VIC/GDM Module, Heated Rear Window Relay Coil,
Illuminated Entry Relay and Chime Module
20)Heated Rear Window Switch, Overdrive Switch, Speed
Control
21)Security Alarm Module, Lamp Outage Module
22)Airbag Module, Speedometer, Tachometer, Telltales and
Gauges
23)Heated Mirror Feed, Heated Rear Window Switch
24)Instrument Panel Illumination
25)Power Seats
26)Power Windows, Power Sunroof
27)Security Alarm Module and Front Wiper
28)Heated Rear Window Relay

Aug 01, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Cant find wer the spark plugs for a 2001 hyundia sonota


Could be a cover over the spark plugs or plugs have coil on plug system: Ignition System WARNING
To avoid personal injury and/or vehicle damage, refer to the service precautions at the beginning of this section.
General Information NOTE: For information on understanding electricity and troubleshooting electrical circuits, please refer to chassis electrical.
Coil on Plug (COP) System
The coil over plug system was developed so that spark and spark timing could be better controlled on an individual cylinder basis. Each cylinder has an ignition coil mounted directly above the spark plug on the cylinder head cover. A short suppresser/connector replaces the spark plug wire and links the coil to the plug. There are different methods used for primary triggering. Some manufacturers use a combination coil/module, which means each coil has its own control circuit that is activated by the PCM. Others use remote mounted modules to trigger the coils.
Each individual coil is allowed to saturate while all other cylinders fire. For a V-8 engine, this allows a period of seven firing events for coil saturation, compared to three events for the same V-8 engine with a waste spark system. The coil over plug system also benefits from a minimum amount of energy lost, due to the resistance of spark plug wires.
Distributor System
If a distributor is not keyed for installation with only one orientation, it could have been removed and installed improperly and then rewired. The new wiring arrangement would maintain the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason it is imperative that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes of the current plug wire locations and orientation of the distributor cap.
Magnetic Sensor / Pick-Up Coil
The magnetic sensor in electronic ignition system is made up of a small coil of wire wrapped around an iron core, a permanent magnet and a toothed wheel called a reluctor. These sensors can be found mounted in a distributor, or at the front, middle, or rear of the crankshaft or camshaft, and are two-wire sensors.
The permanent magnet produces a magnetic field that passes thru the center of the pick-up coil. As the reluctor turns, the small teeth enter the magnetic field. Because the metal is a better conductor for the field than the air between the magnet and reluctor, the field strength begins to increase and reaches its maximum when the reluctor teeth are closest to the sensor. An increase in magnetic field induces a positive voltage to the module. As the teeth leave the magnetic field, the decrease in pole strength induces a negative voltage into the module. This alternating positive and negative voltage causes a small AC current. This alternating current after passing through an analog/digital converter is used by the module or engine controller to trigger the primary circuit.
Hall-Effect Device
Another device that can be used to create a triggering signal is a hall-effect device. A hall-effect device can be thought of as a solid-state On/Off switch. The hall-effect switch is a three-wire device that must receive a power and ground. The hall-effect switch is used in conjunction with an interrupter ring with a series of slots or openings cut into it. Depending on the application, these slots are spaced around the ring in a specific configuration. As the ring rotates, the slots pass between the hall-effect switch, and alternately turns the voltage off and on. When a slot aligns with the hall-effect switch, the controller sees voltage on the signal line. When the area between slots passes the hall-effect switch, the signal is pulled low. This results in a voltage of 0V–0.1V at the controller.
The rotation of the interrupter ring causes the signal to toggle, which causes a continual series of digital pulses on the signal line. This digital pulse is the timing signal that is used by the ignition module or engine computer to open and close the primary circuit. The controller processes these pulses as the RPM signal.
Photo-Optical
Another device used to create a triggering signal is the photo optical sensor. Inside the distributor, there are pick-ups called the Reference pick-up and the Sync pick-up. Each pick-up has a Light Emitting Diode (LED) and a phototransistor. A slotted disc rotates between the pick-ups. The pair of LED’s and phototransistors generates crankshaft position and RPM signals (high and low-resolution signals). The LED’s are powered by a 9- or 12-volt source (depending on manufacturer). Each phototransistor is used to turn a 5-volt signal from the engine controller on and off.
If we look at the optical distributor used in the Chrysler 3.0L engine as an example, there are two areas of slots cut into the disc. The outer diameter of the disc, which generates the high-resolution signal, contains 350 slots. Each of these slots represents 1 degree of crankshaft rotation. An area of approximately 3/8" with no slots represents the remaining 10 degrees. The inner portion of the disc is the low-resolution signal and contains six 60-degree slots. Each of these slots represents the piston’s top dead center position for each cylinder. The controller uses the high-resolution signal to regulate spark timing up to 1200 RPM. This ensures timing accuracy, since crankshaft speed fluctuations are most likely to occur because of the firing pulses during cranking and idle. The low-resolution signal is used for injector firing, as well as ignition timing above 1200 RPM.
As the slots pass between the LED’s and the phototransistors, the transistors are toggled on and off. This occurs as the light beams from the LED’s are alternately interrupted. When the light beam from the LED strikes the phototransistor, the transistor turns on. This causes the 5-volt signal to be pulled low (0V–0.1V). When the rotating disc blocks the light beam, the transistor turns off. This causes the 5-volt signal to remain high.
Ignition Coil
The heart of the automotive ignition system is the ignition coil. The ignition coil is a step-up transformer, since it boosts battery voltage to the high voltage that is necessary for proper combustion.
The ignition coil consists of a primary winding and secondary winding wrapped around a soft iron core. The primary winding is made up of several hundred turns of heavy wire, while the secondary winding consists of thousands of turns of fine wire. The iron core is used to conduct magnetic lines of force efficiently.
When current flows through the primary winding, a magnetic field is created. The more time current is permitted to flow, the stronger the magnetic field becomes. When the current is turned off, the magnetic field collapses causing a high voltage to be induced in the secondary winding through the process of induction.
A few hundred volts will be generated in the primary winding because of the collapsing magnetic field across the heavy primary wire. However, as the magnetic lines of force cut across the thousands of turns of fine wire in the secondary, a far greater voltage is produced. The production of primary voltage is called self-induction, since the primary winding essentially magnifies its own initial voltage when the magnetic field collapses.
Related Symptoms
Faulty ignition system components along with loose connections, bad grounds, high resistance or opens in the circuit, may cause the following symptoms:
  • No start condition
  • Stalling after cold start
  • Stalling after hot start
  • Surging off idle
  • Extended crank time when engine is cold
  • Unstable idle
  • Running rough during off idle acceleration
  • Bucking
  • Hesitation
  • Stumble
  • Poor fuel economy
  • Spark knock

Jul 08, 2010 | 2001 Hyundai Sonata

1 Answer

High pitch winding noise on cold start up.


Sounds like a constricted IAC Idle air control valve passsage. Fairly simple to fix. Remove air filter trunking all the way to the throttle body to allow access. The IAC allows air passed the throttle when closed at idle. Just on the inside of the throttle body in front of the throttle flap there is an opening in the throttle wall. This is the air inlet to the IAC; there is an outlet similar on the other side of the throttle. Use carb cleaner and cloth to shift the grime from this tubing and get it like new. Hold the throttle flap open to get at both ends of the IAC tubing. The IAC can be detached and cleaned to a shine. Reinstall the IAC and replace all air pipe ducting. Leave for about 20 minutes to allow any cleaner residue to dry out. When you restart you might experience a bit of uneven running but this will disappear very quickly as the last of the cleaner dries out

May 04, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

My car wont rev past 2300 rpm & running rich


Hi just wondering if you fixed the problem?

Dec 29, 2009 | 1988 Ford Thunderbird

1 Answer

Need Fuse Map Diagram BMW 318i 1993


check the internet for a bmw e36 ETM ( electronic troubleshooting manual) everything you need is there.

Jun 02, 2009 | 1994 BMW 3 Series

1 Answer

I have 2 Problems: running poorly and my AC


For Problem 1, I have a 02 9-3SE and had/having similar problems. RPM & turbo gauge flucuate at red light. I think the mechanics did a fuel system clean up that solved most of it. Occassionally it's still doing that to me, not as bad.

Apr 30, 2009 | 2004 Saab 9-3

2 Answers

Rpm won't go over 2300


TRY A TUNE UP OR THE COIL PACK I HAD THE SAME PROBLEM

Dec 15, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...