Question about Cars & Trucks

1 Answer

2000 s10 what r. The colors of the wires for the fuel sensor

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

Dont know the colors off hand. But this is what i do know. You will find with a test light. And with the key on one wire will light the test light real dim...that will be the sending unit power out .now have some one turn the key off and on till.you find a wire that lights your test light real bright only for about three seconds then go off. This will be fuel pump relay wire

Posted on Nov 24, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

carfreak1217
  • 109 Answers

SOURCE: Instructions to replace fuel composition sensor

  1. Turn OFF the ignition.
  2. Relieve the fuel pressure
  3. Remove the fuel composition sensor FCS attachment nut.
  4. Remove the 2 FCS attachment bolts.
  5. Remove the FCS from the frame rail.
  6. Disconnect the FCS inlet and outlet pipes from the FCS.
  7. Disconnect the FCS electrical connector.
Installation Procedure


  1. Connect the FCS inlet and outlet pipes to the FCS.
  2. Connect the FCS electrical connector.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the attaching nut.
  5. Tighten
    Tighten the nut to 17 N·m (12.5 lb ft)
  6. Install the 2 FCS attachment bolts.
  7. Tighten
    Tighten the bolts to 17 N·m (12.5 lb ft)

Posted on Jun 27, 2009

  • 18 Answers

SOURCE: I need a wire diagram for a 2000 zr2 s10 chevy 4x4

  1. this should help.8d4efbb.gif

Posted on Aug 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i find a wiring pin out for the instrument cluster of a 2000 Chevrolet S10 pickup


a Chiltons Manual should have the wire colors of what goes where, match the color with the wires going to the pins

May 10, 2017 | 2000 Chevrolet S-10

1 Answer

Sensor located on a 1992 Chevrolet S10 4.3 liter fuel injection TBI pickup?


My info showed this for coolant temp sensor. Two wire connector, wire colors purple and yellow.
cts-0u0cunsitim0obet0icbuu3s-3-0.jpg

Mar 20, 2017 | Chevrolet S 10 Cars & Trucks

1 Answer

I need a color code for the brake light wiring diagram for a 2000 s10 blazer


The S10 and the Blazer are identified as two different vehicles. The left stop light wire is YEL; the right is DK GRN. The center high mount stop lamp wire is LT BLU.

Oct 30, 2016 | 2000 Chevrolet Blazer

2 Answers

What colors r the wires that go to the fuel gauge on a 2000 Chevy s10


If your fuel guage is not working check the ground wire on top of.fuel tank. Most of.the.time the sending unit in the tank is bad....not good news there. Most part stores sell the unit with a new fuel pump only. Cost you some green backs there. More bad news... the fuel tank has to droped to replace it... i my self find it is easyer to unbolt the bed of the truck and raise it up on blocks. Then you can see your wire loom and check your wires with the fuel tank in place.

Nov 24, 2014 | Cars & Trucks

1 Answer

2000 s10 trailer wiring instructions. I need to know how to hook my trailer wiring to my 2000 s10 xtreme.


Try this site. http://www.etrailer.com/faq-wiring.aspx. They give color codes and detailed info. If you have one bulb that does both, running and stop lights, then simple wiring to colors should correct the proble. If you have two bulbs, one for brake and one for turn signal, you must use a converter. Otherwise, it feeds back to whatever you are wired to.

Nov 07, 2010 | 2000 Chevrolet S-10

2 Answers

2000 chevy s10 starts fine but dies out when push


Have you changed the fuel filter lately? If not do so. Sounds like fuel restriction. Filter usually on frame rail passenger side. Good luck!

Apr 13, 2010 | 2000 Chevrolet S-10

2 Answers

2000 S10 no start


I'd use a gage and check proper fuel pressure, key on engine off, 60--66 psi with spider fuel system.
Engine cranking did you visually check for spark at the spark plugs? Engine cranking is there a fuel injector pulse?https://s8.postimg.org/50arofh11/fuel_pump.jpg
Click on the link for fuel pump relay, you can check the fuse. At the fuel pump, gray wire is voltage, black is ground.

Apr 15, 2017 | 1997 Chevrolet S-10 Pickup

1 Answer

I have a 95 s10 4.3 which starts nd runs fines


spider injection is a common problem with these vehicles, is it consuming gas more than usual, is the oil smelling like gas? The spider is located under the upper intake plenem. There is also a fuel pressure regulator connected to the spider assembly that may be faulty.

Dec 31, 2009 | 2000 Chevrolet S-10

1 Answer

Bogging Down 2000 S10 2.2l


start checking fuel systems pressure an volume

Aug 12, 2009 | 2000 Chevrolet S-10

3 Answers

Poor gas mileage 2000 S10 4.3L 4WD


Thats the mass air flow meter.Should get changed at 60.000 miles. Also change the air filter.

Jun 18, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...