Question about Cars & Trucks

1 Answer

How do I find location of junction of signal lights front left signal works rear left staying in right front and rear doesn't work fuses and relay work fine

Checked fuses bulbs all working

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 214 Answers

Go to dealer's service department and they should be able to print the wiring diagram you need. Your problem could be caused by plug and socket bad and the pages would show where all these are in the vehicle.

Posted on Nov 24, 2014

Testimonial: "Dealer doesn't have complete digrams or won't give it to me"

  • James Boone
    James Boone Nov 29, 2014

    Will try thank you

  • BJ Russell Nov 29, 2014

    I just remembered something from years ago. You may have broken contacts for your turn signals switch under the steering wheel.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 150 Answers

SOURCE: 2005 Toyota Sienna rear brake light problem.

have you checked the earthing continuity-if it's this other bulbs may also partly light when brakes used
otherwise-
Check continuity of live from center to lh & rh lights and/or is there a live at those lights

Posted on May 03, 2009

  • 88 Answers

SOURCE: rear brake lights don't work

you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

Posted on May 23, 2009

kidspeedy
  • 321 Answers

SOURCE: left rear turn signal light on my 1999 chev. s10 is not working

any increase in bink speed is direcly related to a bulb being burt out.

Posted on Jun 12, 2009

  • 2 Answers

SOURCE: Brake light, Turn signal not working rear right 06' Focus

I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Posted on Aug 06, 2009

  • 1986 Answers

SOURCE: rear left and right turn signal lights not working.

the electronic flasher module may be faulty, or you could have blown a fuse

Posted on Aug 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alpha Romeo 156 My Left hand indicator light stays on continually, does not flash. and when I turn the hazard light switch on both indicators continually glow.


Generally speaking, symptoms of a bad or failing turn signal bulb are usually the culprit...in your case, either it's the front left or rear bulb. Varies for different vehicle makes...common signs include:
  1. turn signal light staying on solid
  2. or blinking very fast
  3. or either sides of the bulbs stop blinking altogether.
To test this, make sure you reconnect everything you disconnected.
Turn the left signal light on; go to the front of the vehicle, is the turn signal bulb illuminated? If it lights up, even though it is not blinking obviously the bulb is okay. If it doesn't, replace it- problem solved. You'll do the same procedure for the rear turn signal Is that lit up? If not replace the bulb and the problem is solved.
Another common failure is when the turn signal blinks really fast, same procedure as mentioned above.
If both bulbs for the left side and right side illuminate but don't blink, the problem is in the steering column turn signal switch.
If the left or right side blinkers don't work properly at all...then check the integrated hazard warning/turn signal flasher relay- that may be defective; again, that's usually the case if both sides of the signal light don't work.
If you are blowing any fuses related to the flasher system, you have an electrical overload in the turn signal circuitry.

Feb 12, 2017 | Cars & Trucks

1 Answer

Turn signal light right flash


flasher/blinker is busted. this is located under your dash board. remove steering column cover, turn on LEFT turn signal (yes, the one that is working), then you will hear a clicking sound. locate the relay that causes the sound. there you can see 2 relays (one for LEFT, other one for RIGHT turn),replace busted one.

Jun 11, 2013 | 2002 Toyota Tundra

1 Answer

My dashboard and rear lights don't work


Assuming this has the V6, the 15A PARK LPS fuse in the underhood fuse block feeds constant power to the auto park lamp relay. When the relay closes, 12V power passes through the 10A INST LPS fuse in the right instrument panel fuse block to the panel dimmer switch and then to the five instrument cluster lamps.

If by "rear lights" you mean everything in the rear lamp assemblies, power for the tail lights (running lights) starts at the 15A PARKLAMP fuse in the underhood junction block, passes through the automatic lamp control (ALC) relay and the right instrument panel junction block to the tail filament of the dual stop/tail lamp and the separate tail lamp on each side. The 12 V power for the stop lamps is protected by the 20A STOPLAMPS fuse in the left I/P junction block, passes through the stoplamp switch when brakes are applied, stop filament of the dual stop/tail lamps. That leaves the turn signals and the hazard lamps. Power for the turn signals originates at the 10A TURNLAMPS fuse in the left I/P junction block and is applied to the hazard switch. Switch output goes to the turn/headlamp/wiper switch for selection of left or right turn signals. That switch output goes to the turn lamp. Power for the hazard function begins at the 10A HAZRD LPS fuse in the left I/P junction box and goes to the hazard switch. Switch output is sent to the left I/P junction box to make the turn signals flash. That's it. Post a comment if you need more information.

Sep 15, 2012 | 2002 Oldsmobile Alero

1 Answer

Right rear signal works but the left does not. Changed bulbs twice and still have problem


Look inside under the steering wheel to the left,remove the lower steering column cover and knee pad panel to see junction box. The each fuse and relay will be marked for the right turn signal and the left turn signal. Look for a blown fuse on the left side. If not then the relay will be at fault. Before you start look to see if either turn signal lights are working on the left side. If the front is working and the rear is not then it will ba a short in the wiring to the rear causing the problem. Hope this will help you.

May 23, 2010 | 2005 Dodge Grand Caravan

1 Answer

Right turn signal doesn't work.


the next step and almost certainly the problem is the turn signal switch, have seen this symptom on other years around yours and switch fixed it.

Sep 09, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

Driver side signals only work when headlights are OFF


What may have happened is either the headlights wiring or the parking lights wiring somewhere along the wiring fused to the left turn signals wiring. Depending on if the turn signals go on when you put the parking lights on or the headlights on.

If the signals come on when you turn on the headlights than you only need to locate the light green wire that comes off the left turn signal harness.

Next follow that wire the entire way back to the firewall looking for another wire fused to that wire as you go.

If there are no signs of this you need to continue looking on the other side of the firewall all the way back to the turn signal and hazard flasher unit which is a black box that connects to a black harness located next to a grey harness behind the knee bolster.

But if the signals come on when you turn on the parking lights than you will also need to check the wiring from the rear left signal and follow that light green wire all the way back to the turn signal and hazard flasher unit.

This should fix your problem, but if not than your problem may lay within the the wiring between the turn signal/hazard switches and the turn signal and hazard flasher unit.

Also you may have a burnt circuit in the junction block. This block is where the light green from the rear left signal and front left signal meet. Don't have a description but if you cannot find it let me know and I will go out to the yard and look myself and let you know.

Apr 22, 2009 | 2004 Dodge Intrepid

2 Answers

1993 Dodge Shadow...left turn signal won't flash


If the fuses are good and the front and rear bulbs are good, change the flasher for the turn signals, even tho the right is working. If that doesn't fix the problem, it might be in the turn sgnal switch on the steering column.
If both bulbs are good for the backup lights and fuses are good, then the backup light switch, which is screwed into the side of the transmission has to bad.

Apr 12, 2009 | 1993 Dodge Shadow

2 Answers

Front and Rear Right turn signal lights would not work


the first thing i would do is replace the relay seeing the fuses check out ok otherwise there is a relay under the dashboard which could be the problem hope this helps regards Jim

Apr 10, 2009 | 2000 Mitsubishi Galant

1 Answer

1991 Ford E150 turn signals do not work,emergancy flashers flash constantlly unless the flasher relay is unplugged from fuse block


Hi,

If I understand you right based on your post/description, the signal lights would still turn on even if any or both of the flasher relays are removed. Should this be the case, then the signal lights are not getting the power from the flasher relays but from the brake light circuit.

Perhaps your concern is not with any of the flasher, but simply missing or loose ground more particularly with the rear lights. Perhaps you could try determining which of the wires for the brake lights and signal lights (as they come out of the light assembly) would be ground . A test and even possibly a temporary workaround is to hard wire a second ground connection from the determined ground wire of the lights and attach it to any conveniently located bolt or screw to the body. it may be to your advantage to do this on all the rear lights assembly.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 05, 2008 | 2003 Ford E150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...