Question about Cars & Trucks

1 Answer

No start whith thermostat

The start is normal joining the cables, but no with the thermostat

Posted by on


1 Answer

No idea what your saying

Try again & provide more details

Posted on Nov 24, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

FuSO 2007 6m70 10wheeler truck. The power is flactuating. Low power rpm is just 15. When i let it cold. The power wil charged. Whats the proble then? Please help

This sounds like the water thermostat is faulty follow top water hose to where it joins the engines take apart the thermostat is what your looking at take it out place on floor (outside house) tip boiling water over the thermostat it should open up straight away if not buy new one not expensive & replace with new one assemble pipe & thermostat cover (normally made on aluminum) everything should now be okay working fine. Cheers, Malcolm Campbell.

Apr 01, 2017 | Cars & Trucks

1 Answer

How do I remove the radiator fan guard so I could change the thermostat

Hi's a link to a repair guide on changing your thermostat,it's a lot of work.Join Autozone's site,become a member,it's free,then you can use all their repair guides like me. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

Relieving Fuel System Pressure

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the fuel pump fuse from the panel.
  3. Start the engine and allow it to run until it stalls. Crank the engine for a few seconds to relieve additional fuel pressure.
  4. Disconnect the negative battery cable.
  5. When repairs are complete, replace the fuel pump fuse and connect the negative battery cable.

Jan 07, 2016 | 2002 Nissan Pathfinder

1 Answer


Normally follow top or bottom radiator hose,,,,where they join the engine thermostat normally close by

Jun 13, 2013 | 1991 Buick Regal

1 Answer

Caprice 2008 LS V6, AC works perfectly on highway but stops working when I slow down or on traffic lights?

no idea offhand if their are external wires running to the thermostat then it may be possible to join them but if a manual one inside the pump then yes it will have to be stripped and changed if its possible to strip it with normal tools as some units just do not come apart

May 11, 2012 | Cars & Trucks

1 Answer

The heater will not blow warm air until you start driving. The fan blows but its cold air. Once you start driving the air turns warm. Why?

There may not be enough coolant in the system. What happends is the heating core is nothing more than a small radiator inside the car. If the fluid is low the heating core is empty. But once you start driving the water pump works harder and fills it up. Another possible cause is a sticking thermostat. If its stuck open the engine cant retain water to heat it up. Thus blowing cold air. Whith the engine cold remove the radiator cap and check your coolant level. If it is full a replacement thermostat may be needed. HTH and dont forget to rate.

Dec 06, 2010 | 2003 Dodge Stratus

2 Answers

CAR starts whith a jump when you remove jumper cables cars shuts off

Replace battery with a good charged on and test the alternator. Advance Auto will test the alt free. Just drive the car there with the new battery during the day.

Oct 15, 2010 | 1994 Honda Accord

1 Answer

How do you release the parking break when the release cable is broken.

rear axis ankering whith two parking cables one cable easy to repair when unscrew cable spaner on 13 ...12..10?

Aug 08, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

Cooling fan wont come on when car reaches operating temp

There is either a break in the cable, which when you push the plug back on you get connection, or the switch is gone. I would say there is a break/lose connection where the cable joins the plug that actually joins the switch. try this. Get a pair of pliers and crimp the joint tightly. If this doesn't work, cut the wire as close to the plug as you can, bare about 5mm of the end of the cable, slip it into the contact side of the plug and push onto the switch, then if it's still the same do the same with the other side. Bet it works! Go to a motor factors, get two new plugs to fit on the prongs, crimp the bared cable into the plugs and he-presto! A repair for $1.00

Jul 23, 2009 | 1999 Oldsmobile Cutlass

2 Answers

I want to know where the thermostat is located

Assuming you mean the thermostat for the coolant...
For the 1.9TDI lump, look at engine, right side, low down, where several pipes join. It's held in by a pair of (I think) hex-head bolts. The heads can't be seen from the front because they face down & backward. Expect to lose coolant.

May 07, 2009 | 1999 Audi A6

1 Answer

Engine audi a6 1999


Mar 05, 2009 | 1999 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides