Question about Seat Cars & Trucks

2 Answers

How do I get a seat belt that is stuck in the buckle out

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 424 Answers

You can also try spraying a silicone lubricant into the slot and jiggling the latch and insert.

Posted on Nov 26, 2014

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Push the seatbelt harder in and push release see if that works

Posted on Nov 26, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: Seat belt problem

In my past experience with wiring in a car and seat belt lights I have found that most every newer vehicle will have a single negative lead wire running to some sort of switch in the seat belt locking mechanism. When the male end of the belt is placed into the female lock the switch will be depressed and grounded to complete a circut then turn off the light. If any switch is damaged and does not complete the circut then the light will not turn off. This may be the problem but it could also be a simple computer glitch in your vehicle. Another problem could also just be a blown fuse that triggers the light to come on as a precaution. A call to your local auto parts store may be able to help you more. I am just a self learning mechanic and not very computer savy.

Posted on Oct 31, 2008

polarcycle
  • 1392 Answers

SOURCE: Seat belt buckle receiver will

I guess you answered your own question.

Posted on Mar 06, 2009

  • 9 Answers

SOURCE: seat belt alarm goes off when belt is buckled

try relapsing the switch inside the female of the seat belt

1024d1201421548-seat-belt-alarm-seatbelt-pretensioner.jpg

Posted on Apr 17, 2009

  • 5 Answers

SOURCE: Seat belt buckle receiver will

If it's not a coin, look inside the buckle again, compare it with a properly working latch. If you see something inside the broken latch that looks like it may be protruding out from the back, try pushing it back with a flathead or key, then pop the push button back up with the same tool you used... I have to do this each time I get out of my truck because the spring is broken. It still should work fine, it's just missing a spring that reset the latch to it's resting position. If you're still skeptical about it though, it's like a 25 dollar fix with installation.

Posted on Sep 04, 2009

jeffbvegas1
  • 520 Answers

SOURCE: how to replace seat belt buckle on Honda? civic

This rtequires seat removal in order to gain acces to the buck side mounting bolt

Posted on Sep 18, 2009

Testimonial: "Very helpfull"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heated and cooled seat on 2004 expedition stopped working how to reset them


Heating and the cooling both don't work ? Just one seat or all seats ?
Your best bet have it checked for DTC'S - diagnostic trouble codes to start .
Climate Controlled Seat Module (CCSM) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU Is Faulted CCSM INSTALL a new CCSM and CARRY OUT programmable module installation (PMI). REFER to Climate Controlled Seat Module . B1358 Ignition Switch or Blower Electronics Circuit Short to Ground CCSM Go To Pinpoint Test Q . B2477 Module Configuration Error CCSM This DTC indicates programmable module installation (PMI) has not been done to a newly installed module. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. B2486 Climate Controlled Seat Module Voltage Out of Range CCSM DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 294 (WH/LB) for a fault. REPAIR as needed. If okay, REFER to Section 414-01 . Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . B2488 Thumbwheel Switch Voltage Out of Range High CCSM Go To Pinpoint Test R . B2521 Tach Circuit Failure CCSM Go To Pinpoint Test Q . B2729 Cushion Over-Temp Detected CCSM Go To Pinpoint Test S . B2730 Back Over-Temp Detected CCSM Go To Pinpoint Test S . B2731 Differential Temperature Fault CCSM Go To Pinpoint Test S . B2792 Heat Switch Short to Ground CCSM NOTE: If HEAT is pressed for greater than 20 seconds on the climate controlled seat switch, DTC B2792 will set in the CCSM.
CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 1551 (VT/WH) for a short to ground. REPAIR as needed. If okay, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . B2793 Cool Switch Short to Ground CCSM NOTE: If COOL is pressed for greater than 20 seconds on the climate controlled seat switch, DTC B2793 will set in the CCSM.
CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 1550 (WH/OG) for a short to ground. REPAIR as needed. If okay, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . U2362 UBP Invalid Data Node ID CCSM NOTE: DTC U2362 indicates a network concern, the CCSM is not the source of the fault.
CLEAR the DTC. If the DTC does not clear, REFER Section 418-01 .

Nov 26, 2016 | 2004 Ford Expedition

Tip

Middle seat belt buckle tip for booster seats, car seats, and large humans.


In trying to fit a booster seat into my 2004 Honda CR-V, I realized that the CRV has the belt buckle in the middle of the seat. This is a big problem for someone using a child seat in the middle seat as the buckle receptacle is completely covered by the booster seat. I thought about buying an extender but realized it wouldn't completely solve the problem. After much thought I came to the conclusion that the buckle receptacle could be moved to a new location without compromising any safety of the belt. I first pulled the buckle receptacle all the way out and then cut the fabric to enlarge the hole from which it protrudes from the seat. Then I pushed it through the hole and back into the seat with the head pointing towards the window and outer edge of the seat. After flipping the window seat out of the way I was able to peel the fabric away from the bottom edge of the middle seat enough to reach in and retrieve the belt receptacle. It was a little tight but I was able to buckle the belt and use the seat belt to pull the receptacle through this new "hole" and VOLIA the belt receptacle is now in a better position to the side of the middle seat. You can now used a booster or car seat or put a fully grown human in this seat and buckle with ease.

on May 20, 2015 | Cars & Trucks

1 Answer

Seat belt sensor goes on and off as your driving with all seat belts on


Look for garbage in the drivers seat buckle.

Make sure there is no heavy weight in the passenger seat.

You likely need a seat buckle, but could be wiring.

Dec 29, 2014 | 2008 Chevrolet Uplander

1 Answer

Broken seat belt buckle


If I had the problem I would look at a junkyard or on line at e-bay for a replacement. You will need to get the buckle and the belt that it is attached to that goes down to the floor down through the crack in the seat.
Remember the buckle receiver is made for the certain belt in the front and rear seats. I have often tried to put the wrong belt in a buckle and it would not fit. ( Example: the right belt goes in the right buckle.)
Be blessed.

Nov 08, 2013 | 2002 Nissan Xterra

1 Answer

I have a 1994 mercedes SL320 Conv. the seat belt light on dash will not go out. any suggestions


faulty seat belt buckle or wiring, first check wiring for seat belt buckle if wiring and connectors are OK require new belt buckle, is this information helped you?

Oct 26, 2010 | Mercedes-Benz SL65 Cars & Trucks

1 Answer

My seat belt light is on when i have the seat belt on in toyota camry 1995


sensor may be stuck inside your seatbelt. spray a lube inside it and put it together and take it apart 5 or 6 times just to get it to loosen. do this to the passenger side as well. if this doesnt work then some cars have a sensor built into the seat that tells the car you have a passenger that isnt buckled. its possible that this sensor is stuck. should be located under seat but can be checked by simply buckling the passenger seat belt and seeing if the light goes out.

Aug 22, 2010 | Toyota Camry Cars & Trucks

1 Answer

Is there a way to turn off the beeping noise that happens when the seat belt is not buckled on a 2007 Tundra?


Easiest and smartest way would be to buckle your safety belt:)

If your like my grandmother and swear that it will keep you stuck in your vehicle when you need to get out fast, then you can unhook the pressure sensor in the drivers seat that recognizes when there is weight on the seat and no seat belt buckled.

757Nate

Dec 06, 2009 | Toyota Tundra Cars & Trucks

1 Answer

Seat belt noise wont stop even went i have the seat belt on


On most any car, the best way to stop buckle noise, plus add instant easy, stuck in car after accident release, for only $20 is below:
http://www.nucow.com/buckle/bucklepup.html

Jul 22, 2008 | Honda Accord Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Adam Truesdale

Level 2 Expert

265 Answers

Are you a Seat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...