Question about Cars & Trucks

1 Answer

Clutch pedal interchange for 1994 suzuki sidekick

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 69 Answers

What is the question? Please give detailed description of the problem. Thank you.

Posted on Nov 26, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 140 Answers

SOURCE: I CAN'T FIND THE TURN SIGNAL FLASHER ON A 1994 SUZUKI SIDEKICK

IF YOU CAN FIND THE FUSE BOX, ITS LOOK LIKE A LITTLE METAL ROUND CIRCLE PEACE,IF YOU PULL IT OUT IT LOOKS LIKE A FUSE ON THE END THAT GOES INTO THE FUSE BOX.. IF ITS NOT IN THE FUSE YOU CAN CALL ANY PARTS STORE AND THEY CAN GIVE YOU A LOCATE ON THE FLASHER..THANKS AND GOOD LUCK..KEITH..

Posted on Mar 11, 2009

  • 1 Answer

SOURCE: Automatic transmission for 1994 suzuki Sidekick JLX?

how to disconnect trque conveter to drive plate. 1995 suzuki sidekick jlx 4x4

Posted on May 26, 2009

boysor2933
  • 293 Answers

SOURCE: suzuki sidekick clutch problem

Check the cable clearance. Too much clearance will cause clutch slippage or total clutch disengagement. Adjust the cable so that the clutch pedal will be hard to press by hand .5 to .75 inch from its initial point.

Posted on May 28, 2009

germcelchar
  • 389 Answers

SOURCE: How do you adjust a clutch on a 1998 suzuki

A lot of fluid clutches cannot be adjusted. Any that can be adjusted is with slave cylinder The small round bar from the slave cylinder to the plate from the bell housing which holds the trust bearing. Check it you will easily see the adjuster on it if it has one. If your clutch is'nt badly worn and it cannot be adjusted then try bleeding the slave cylinder it may be air. If it is hard to put into gear and the car moves off when you lift your foot up 2 to 3 inches then it needs adjusting if not then the clutch is worn and adjustment won't help. Cheer's

Posted on Sep 26, 2009

  • 832 Answers

SOURCE: My 1994 ford rangers clutch pedal just lost all pedal

There are two types of clutch actuators. (Mechanical & Hydtraulic)
A. For mechanical type,- Check the clutch cable as
this could be cut from wear and tear. This is easy
to replace. You can find this connected to the
pedal and the clutch lever near the transmission.
B.For hydraulic operated - Check the level of the
hydraulic oil at the cylinder of the hydraulic
actuator under the hood. This actuator is
directly connected to the pushrod driven by the
pedal. If the actuator is leaking, you have buy
a repair kit (Hyraulic clutch repair kit for Ford
Ranger 1994 MOdel.) These items must be
repaired to activate your pedal.

Posted on Oct 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1993 suzuki sidekick 16v replaced the clutch cable as is was shredded have adjusted several times but it continues to get harder to depress the clutch pedal and change gears do i need to replace...


you did not say how long (time or miles) it took to damage the cable.
did you lube the cable, each time? replaced?
and yes, if the collar on the front of the trans, or the main spline
shaft to the transmissiion are galled, or the throwout bearing is bad
or worn at same points, it will bind.

if the pedal binds, with a new cable , the clutch is bad
10hrs labor for 4wd. (done many, )
can be less if you have top tools.
I find pulling the engine, faster. (tools)

did you use a non china clone cable?
or a good one.
i have friends that used the plastic clone cable, they are all junk.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

try a real suzuki cable.
23710- 57B11 (obsolete at Suz says use B12)

or a BECK. 093-0623 (nut mount) 62"?
later cars have rubber mounted at end.
take care not to order wrong cable.

Sep 20, 2013 | 1993 Suzuki Sidekick

1 Answer

Had 2nd clutch replaced on 95 sidekick still haven big problems with it. After it warms up clutch does not want to work. Pleeeeease help with this problem


did you adjust the clutch pedal anytime.Improper adjustment will cause the clutch to engage but it will not release it and therefore you will end up with a burnt clutch

Aug 04, 2011 | 1989 Suzuki Sidekick

1 Answer

I noticed there is threaded adjustment on the clutch pedal push rod going into the clutch's master cylinder hydraulic system. Is this one way I can adjust the hydraulic clutch on my 1998 suzuki sidekick...


Yes, if you need a little oomph out of the pedal, you can get a little more throw out of the adj rod, or you can get a little less, it doesn't take much to move a clutch. Depends on what the clutch is doing, chattering, slipping, grinding, not shifting. You know, that kind of stuff all gets different adj. Check it out.

Jul 07, 2010 | 1998 Suzuki Sidekick

1 Answer

How to bleed slave cylinder for 1997 suzuki sidekick


Hi if the sidekick is the same as the uk vitara then they don't have a slave cylinder just a clutch cable with a nut near the end to adjust it. If its like a grand vitara they have got a slave cylinder, just crack the bleed nipple off put one end of a small pipe on the end of the nipple and drop the other end in a bottle that is roughly half full of break and clutch fluid, ask someone to pump the clutch pedal until no more air bubbles are coming out then tighten the bleed nipple back up. make sure to keep a check on brake fluid levels while doing this.

Apr 28, 2010 | 1997 Suzuki Sidekick

1 Answer

Bled the clutch and slave cylinder on 97 suzuki sidekick sport and I still have no clutch pedal


You may have a worn out clutch master cylinder. Check if there's fluid leak at the rear portion of the cylinder.

Jul 08, 2009 | 1997 Suzuki Sidekick

1 Answer

My clutch was working fine now have no pedal


check slave to see if it is leaking,however still could be bad and not leak. check the clutch master

Jul 06, 2009 | 1994 Suzuki Sidekick

1 Answer

Suzuki sidekick clutch problem


Check the cable clearance. Too much clearance will cause clutch slippage or total clutch disengagement. Adjust the cable so that the clutch pedal will be hard to press by hand .5 to .75 inch from its initial point.

May 27, 2009 | 1996 Suzuki Sidekick

1 Answer

Automatic transmission for 1994 suzuki Sidekick JLX?


how to disconnect trque conveter to drive plate. 1995 suzuki sidekick jlx 4x4

Apr 15, 2009 | 1994 Suzuki Sidekick

2 Answers

Clutch problems on my 1996 Suzuki Sidekick


Check under the dash where the clutch cable hooks up to the clutch pedal the splines shaft to the clutch pedal may be worn on the shaft. Weld or replace the cheap made parts

Jun 28, 2008 | 1996 Suzuki Sidekick

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...