Question about Cars & Trucks

1 Answer

How doi replacing o rings on my 97 s10 2.2 motor

how doi replacing o rings on my 97 s10 2.2 motor

Posted by on

  • Austyn Goodman
    Austyn Goodman Nov 23, 2014

    Hi terry couey, I want to help you with your question, but I need more information from you. Can you please add details(which O-Rings) in the comment box?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Remove the cylinder head. Then remove oil pan. Unbolts rods one at a time and pull piston out the top. Hone cylinder install new ting on piston and reinstall. (Make sure rod cap goes back on same rod and same direction don't for get to torque the bolts on the rod cap)

Posted on Nov 26, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Buick engine swap,94 3800 motor into 97 lesabre ,is it compatable?


Well there are several 3.8 liter engines 8th digit in the vin tells it all Vin3,C,K,L are all different is small settle ways the most is ignition electronics Vin 3 engines only use the inner sensor ring on crank pulley Vin 3, c,k,l use both sensor rings but they are different also Changing the pulley is not recommended due to balance issues but the sensor rings are bolted on with sheer bolts that can be removed. Intake manifold design is the second most important plastic 2 piece and metal one piece are not inter change able.

Apr 25, 2014 | 1997 Buick LeSabre

1 Answer

Piston rings


You don't replace just piston rings on a motor
with 15 years of cylinder & valve wear
The motor needs to be bored & completely
rebuilt
Should never get involved with friends or
family for anything

Jul 18, 2013 | Saturn SL Cars & Trucks

1 Answer

How can I get the front axles on my 97 Jeep Grand Cherokee to disengage and into neutral?


  1. Raise and support the vehicle safely. Position a drain pan under the shift motor.
  2. Disconnect the vacuum harness. Remove the housing attaching bolts. Remove the housing, motor and shift fork as a unit. Mark the shift fork for installation reference.
  3. Rotate the shift motor and remove the shift fork and motor retaining snaprings. Remove the shift motor from the housing.



0900c152800a9ea8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Shift motor and housing removal

  1. Remove the O-ring seal and discard.

To install:
  1. Add 5 oz. of gear lubricant to the axle through the shift motor housing opening.
  2. Install a replacement O-ring seal on the shift motor. Install the motor in the housing with the retaining snaprings and slide the shift fork onto the shaft with the reference marks aligned.
  3. Engage the shift fork with the shift collar and install the attaching bolts. Tighten to 101 inch lbs. (137 Nm).
  4. Connect the vacuum harness, lower the vehicle and road test.
  5. It could be damaged extreme 4x4 replaced one with a heavy duty unit

Nov 03, 2011 | 1997 Jeep Grand Cherokee

1 Answer

My 97 Grand Cherokee is locked in four wheel drive. How do I get the front axles to disengage


  1. Raise and support the vehicle safely. Position a drain pan under the shift motor.
  2. Disconnect the vacuum harness. Remove the housing attaching bolts. Remove the housing, motor and shift fork as a unit. Mark the shift fork for installation reference.
  3. Rotate the shift motor and remove the shift fork and motor retaining snaprings. Remove the shift motor from the housing.



0900c152800a9ea8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Shift motor and housing removal

  1. Remove the O-ring seal and discard.

To install:
  1. Add 5 oz. of gear lubricant to the axle through the shift motor housing opening.
  2. Install a replacement O-ring seal on the shift motor. Install the motor in the housing with the retaining snaprings and slide the shift fork onto the shaft with the reference marks aligned.
  3. Engage the shift fork with the shift collar and install the attaching bolts. Tighten to 101 inch lbs. (137 Nm).
  4. Connect the vacuum harness, lower the vehicle and road test.

Nov 03, 2011 | 1997 Jeep Grand Cherokee

1 Answer

My 97 Honda Civic is still leaking oil after


would need to see it to diagnose it ,sorry for no instant fix ,could be a rocker cover gasket ??leave distributor alone whilst it works do not play with it

Mar 02, 2010 | 1997 Honda Civic

2 Answers

Torque wrench settings for 97 hyundai lantra 1.8


They use throw away bolts. One use only, so don't reuse your old ones. You will need new ones. The smaller bolts 1st torque setting 22Ft/Lbs and the larger 26ft/lbs, the 2nd torque setting 60 degrees both bolt sizes and the 60 degrees for the third.

May 20, 2009 | 1997 Hyundai Elantra

3 Answers

97 dodge caravan 3.0 engine leaking water


Try checking all the way around the head gasket.

Jan 19, 2009 | 1997 Dodge Caravan

1 Answer

What size battery doi need for a 97 oldsmobile achieva 4 cylinder


Interstate Batteries call for battery part # MT-75
And MT-75-Mega, Both have a average price of $100 - $120 .
Your local sears sells Die Hard and they install it as well.
If you get a cheap battery, buy real nice shoes. You will need them.

Jan 15, 2009 | 1997 Oldsmobile Achieva

2 Answers

97 neon oil leak


Solution: Maybe.

Rear main seal is probably the problem.

My 1997 Dodge Neon has this same problem. My father-in-law (who used to be a mechanic) checked the car for me and found the rear main seal needs replacing.

SEScott1217

Nov 29, 2008 | 1997 Dodge Neon

1 Answer

97 eclipse


i think you might want to look at your idle step up motor as they are a usual problem with mitsubishis sometimes they can be fixed by pulling them out and spray with carby cleaner just make sure you replace the o ring

Jun 30, 2008 | 1997 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...