Question about 2008 Ford Fusion

1 Answer

I have a 2008 Ford Fusion and the seat belt chime goes off all the time even if the seat belt is worn. How do I fix that?

See question above. I just bought this car.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Filmmaker:

    Uploaded 5 video answers.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 12 Answers

This veh has an airbag system and that lamp system is part of it. It is not recommended for one without the proper training to attempt to diagnose or repair due to the danger of setting off the airbags.
It needs to be scanned by a shop that has a scanner that is capable of scanning the RCM (Airbag System)system.

Chances are the seat belt buckle switch is bad or switch is unhooked. that would require replacement or re-connection.
if you try and look at it for connection be sure and unhook the neg battery cable and wait about 15-20 min for the back reserves to deplete in the RCM.
I have a 2008 Ford Fusion and the seat belt chime  - 25294131-y12x0o0o0lm2kgfxdyqglnjp-1-0.jpg

Here is a wiring diagram of the seat switch. Drivers and passenger side.

Posted on Nov 23, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: Arter I put on Seat Belt, another chime goes on for 6 rings,then stops

HI.
ON Ford cars and Suv's,
Some times the sound chime after the seat belt buklet.
Is like a open door.
The problem on this car is that the the DOOR AJAR SWITCH. come danaged. and the Body cumputer don't recievethe door close signal.
But is intermitent.
The door ajar switch is on the door lacth.
You only can get front the dealer.
OK. I hope this information can be useful for you.

Thank you.

Posted on Jul 17, 2008

  • 9 Answers

SOURCE: seat belt alarm goes off when belt is buckled

try relapsing the switch inside the female of the seat belt

1024d1201421548-seat-belt-alarm-seatbelt-pretensioner.jpg

Posted on Apr 17, 2009

  • 1 Answer

SOURCE: 2008 Ford Fusion Wing Mirror Replacement

I checked Ford Focus mirror replacement and it seems to be the same. This is for the manual, unheated mirror.

Remove the mirror cover inside the door - slide a screwdriver behind the cover and pry loose carefully.

Remove the single 10mm bolt and the mirror comes free.
NB. Do not drop the bolt into the door.

Posted on May 22, 2009

  • 1779 Answers

SOURCE: 2008 ford fusion alerts on dashboard

You can download a free owners manual from this site, it will identify all the dashboard alerts:
https://www.fleet.ford.com/maintenance/owners_manuals/results.asp

Posted on Aug 13, 2009

  • 4848 Answers

SOURCE: how do i remove radio from 2008 ford fusion radio ...

http://www.fitaudio.com/index.php?CategoryID=13

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The car just clicks and doesn't start.


Hello,

You may need to drive the car back to where you bought the battery. You may have a faulty battery or faulty alternator. When the car is running it should be charging from about 13.8amps and above. If the battery is completely depleted, a jump pack will not be able to jump start the vehicle.

Hope that helps.

G

Dec 02, 2014 | 1998 Volkswagen Passat

2 Answers

I have a 2008 Ford Fusion and the seat belt chime will not go off even when the seat belt is buckled. What do I need to do to fix that?


There are a few things you can do...
1: If you bought the car from a dealership, take it back. Make them fix it.
2: There is a(should be) a wire going into the receiver for the seatbelt. Ensure it is plugged in. If it is... you can remove the wire and ground it out(ie: loosen the bolt to the bottom of the seat, place wire under bolt. Ensure there will be wire to metal contact. Then, tighten the bolt.)

Nov 22, 2014 | 2008 Ford Fusion

2 Answers

In my 2006 ford fusion 2.3L whenever I put my key in the ignition and turn it a weird solid ringing sound start and stops 5 seconds later hat could it be?


Not surprisingly, many others have experienced problems with the ignition switch on this car. Historically, it is not a sound, but that the key is stuck in the ignition. http://repairpal.com/key-will-not-come-out-of-ignition-570 Your problem sounds different, but it may be related. Although I do not recommend the fix in the link above, it is possible the previous owner of your car did perform this fix and it has resulted in the problem you now have. My better guess is that the chime/buzzer has failed due to moisture or dirt and is no longer producing the sound that it should, but instead is altered to the ringing you describe.To disable follow these instructions:

1. Turn the ignition switch to the RUN (or ON) position. (DO NOT
START THE ENGINE)
2. Wait until the safety belt warning light turns off. (Approximately 1
minute)
Step 3 must be completed within 50 seconds after the safety belt
warning light turns off.
3. For the seating position being disabled, at a moderate speed, buckle
then unbuckle the safety belt 9 times, ending in the unbuckled state.
(Step 3 must be completed within 50 seconds after the safety belt
warning light turns off.)
After Step 3, the safety belt warning light will be turned on for three
seconds.
4. Within 10 seconds of the light turning on, at a moderate speed, buckle
then unbuckle the safety belt.
This will disable the BeltMinder feature for that seating position if it
is currently enabled. As confirmation, the safety belt warning light will
flash 4 times per second for 3 seconds.
This will enable the BeltMinder feature for that seating position if it
is currently disabled. As confirmation, the safety belt warning light will
flash 4 times per second for 3 seconds, followed by 3 seconds with the
light off, then followed by the safety belt warning light flashing 4 times
per second for 3 seconds again.
I hope this helps. Good luck.

Jun 12, 2014 | 2006 Ford Fusion

2 Answers

2008 Ford Escape front passenger seat belt is completely locked up and won't extend. How do I fix this?


the seat belt mechanism could be getting worn out. usually you would have to replace the seat belt retractor but try some WD-40 and see if that helps

Nov 11, 2013 | 2008 Ford Escape

1 Answer

Overheating engine


it sounds more like a timing problem, if it only does it above a certain velocity. get your cars timing checked

Apr 25, 2013 | Cars & Trucks

1 Answer

I added dex cool to regular anitfreeze what will happen


Best is to drain the cooling system and fill the correct antifreeze mixture.

Aug 22, 2012 | 2003 Chevrolet Impala

1 Answer

When do I change the timing belt on a 2004 Ford Fusion?


believe the Fusion has a timing chain and not a belt. but the owner's manual under maintenance can tell you when either service is required.

Jun 06, 2012 | 2008 Ford Fusion

1 Answer

I wanted to know if my 2008 Ford Fusion has a timing belt and when it should be changed. I have read my manual but it doesn't have anything about the timing belt.


Most car manufacturer advised to replace the timing belt at 100,000km/ 2years which ever comes first
But most car owner changed their timing belt at about 80,000km. they dont wait for a hundred thousand.

Sep 17, 2011 | 2008 Ford Fusion

1 Answer

1989 XJS 12 , Lucas ignition vehicle . Temp guage climbs to just above the"N" , some times higher at times , but settles back above the "N". Does not change at higher speeds , when...


Make sure your auxiliary cooling fan is operation. (engine bay, left side of the radiator) When the A/C is on or the car reaches normal temperature, the aux fan should kick on and continue to run until the car reaches a lower temperature. If the fan is not working then check for power to the fan. If you have no power then check on the left inner fender for a blue pektron (relay looking item) If there is power there then the fan is bad.

Aug 09, 2011 | Jaguar XJ12 Cars & Trucks

1 Answer

2007 Ford Fusion, electronic clicking sound under driver seat when slowing dow, stopping, stopped or upon resuming acceleration.


only the airbag connections under the seat ,but their is also a pressure sensor as well i think last time i cleaned the contacts on the airbag wires mtheir is a pyrotechnic device as well to pull the seat belt in if a collision ,so have a good look to try to see whats causing the noise ,sure you havent a coca cola can rolling around??

Mar 17, 2011 | 2008 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...