Problem multiple cylinder missfire. Cylanders 1,3,5 . Variable valve timing. For a toyota avalon 3.0 L. V.6

code p 1354 refers to variable valve timing system malfunction bank 2
causes are problem with valve timing
dirty or low engine oil level
problem VVT ( variable valve timing) controller assembly
faulty oil control valve
defective PCM
It works like this
although the valve timing is initially set at the pulley, that pulley is attached to a moveable section that controls the actual valve timing as is required by different rpm and load settings
That moving action is controlled by a solenoid and oil pressure from the engine
indications of a problem in that area
rough idling
under powered engine

There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

The number 1 cylinder is located at the rear left of the engine, looking from front to back of the vehicle.

P1354 Toyota Description
Variable Valve Timing (VVT) system controls the intake valve timing to proper timing in response to driving condition. The Engine Control Module (ECM) controls Oil Control Valve (OCV) to make the intake valve timing properly, and, oil pressure controlled with OCV is supplied to the VVT controller, and then, VVT controller changes relative position between the camshaft and the crankshaft.

Read more: http://engine-codes.com/p1354_toyota.html#ixzz3LEjKp1Z2

Code 1349 is a problem with the variable valve timing components on the cylinder head for cylinder one.
You'll need to have a mechanic check it out.

P0301 Cylinder No. 1 Misfire Detected
P0302 Cylinder No. 2 Misfire Detected
P0303 Cylinder No. 3 Misfire Detected
P0304 Cylinder No. 4 Misfire Detected
P0305 Cylinder No. 5 Misfire Detected
P0306 Cylinder No. 6 Misfire Detected
P1346 Variable Valve Timing (VVT) Circuit Range/Performance Fault
P1349 Variable Valve Timing (VVT) System Malfunction
P0330 Knock Sensor
P0446 EVAP Vent Control Fault
P0430 Catalyst System

Stop driving immediately.....

You defiantly skipped on your timing........

TRY THIS FRONT 3 CYLINDERS FACING YOU LEFT TO RIGHT 2 4 6 AND BACK CYLINDERS LEFT TO RIGHT 1 3 5 NOW TAKE THIS NUMBER 5 1 3 THIS IS SPARK PLUG WIRES LOCATION FROM LEFT TO RIGHT.PUT PLUGS WIRES TO THE 3 BACK CYLINDERS IN SAME ORDER YOU SEE NUMBER.LET ME KNOW WHAT HAPPENS.

1998 Toyota Avalon XLS 3.0 liter DOHC V-6 (1MZ-FE)




I hope help with this (remember to rate and comment this).

p0352
Ignition coil B primary or secondary circuit malfunction
p0300
Random/multiple cylinder misfire detected
p03001
cylinder no.1 misfire detected
p0306
cylinder no.6 misfire detected
check you coils and spark plugs
make sure they are in good shape. check you spark plug wires also.

A flashing check engine light indicates a cylinder missfire. A evaporative emissions leak (the result of a bad gas cap) wouldn't cause a rough running condition. How many miles are on the vehicle?