Question about Chrysler Cars & Trucks

1 Answer

How to replace the brake light bulb in 2010 Chrysler Sebring retractable hardtop

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

Open the trunk, remove the plastic jamb cover and then the interior cover from the inside of whichever side you want to remove, the remove the plastic wing nuts, and the tail lamp assembly should pop right out allowing you access to the bulb housings which twist lock in to the back of the housing. Hope that helped!

Posted on Nov 25, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: bulb repair....

Hi my name is Allen!

Here is how to change the brake light bulbs, first pull the carpet down that runs up the back covering where the light assembly is installed, next grab the wing nuts, they are black in color, they are designed so you can turn them with your fingers, remove all of them, then pull straight out with the brake lamp assembly.

After the assembly is removed, grab the socket on the back with the wires coming out of it and turn it counter clockwise and pull it straight out, then grab the bulb and pull it straight out and push the new one back in, that's it.

For further assistance contact me at FixYa!

Posted on Jan 01, 2009

jgwhomeequip
  • 1902 Answers

SOURCE: replacing headlight bulbs on a 2006 chrysler sebring

Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Posted on Feb 06, 2009

  • 47 Answers

SOURCE: replacing brake light above trunk on 2006 chrysler

This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Posted on Mar 12, 2010

dttech
  • 4803 Answers

SOURCE: 2002 chrysler sebring, the drivers tail light,

Is your lense cracked where water can get into the housing? Are you absolutely certain that you are replacing it with the correct bulb? Are you using a good name brand bulb like Wagner or Sylvania? or some off-brand cheap bulb made in China?

Posted on Dec 18, 2010

  • 752 Answers

SOURCE: I have a 1999 hardtop

First mistake is replacing anything. Your ECM temp sensor may be bad. Check for codes.

Posted on May 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the brake light in a 2010 chrysler sebring.


Which bake light, upper high mount or lower brake light?

Jul 18, 2017 | Chrysler Cars & Trucks

1 Answer

Got my front brakes and rotor replace also some sensors and now my brakes light do not work checked the bulbs the fuses and the switch and it is not that what could it be they worked before I had the work...


Unless he replaced a brake booster, he didn't go anywhere near the brake light circuit. It needs to be troubleshooted to find the problem before you can begin to determine how it happened.

Aug 27, 2013 | 2010 Chrysler Sebring Touring

1 Answer

Problem with tail lights in 2010 Sebring.


sounds like the brake light switch that is on the brake pedal

Dec 07, 2012 | 2010 Chrysler Sebring

2 Answers

Chrysler sebring sedan 2010 touring model: antilock brake light stays on


it might be a odd sensor going off. your going to have to take it to a Chrysler shop or someone that owns a a diagnostic tool that can hook it up and see what the problem is. They will most like shut off the light if its a minor problem that won't affect the vehicle.

Nov 22, 2011 | Cars & Trucks

1 Answer

2002 chrysler sebring, the drivers tail light, running light portion of the bulb keeps blowing, brake and signal are fine.


Is your lense cracked where water can get into the housing? Are you absolutely certain that you are replacing it with the correct bulb? Are you using a good name brand bulb like Wagner or Sylvania? or some off-brand cheap bulb made in China?

Dec 18, 2010 | 2002 Chrysler Sebring

1 Answer

2000 Chrysler Sebring Convert brake lights


Let's assume you've checked the bulbs and are happy they are serviceable. Therefore you can examine the brake switch input and output (while pedal is depredded)Usually located in the pedal box area of the drivers foot well ! Good luck

Apr 08, 2010 | 2004 Chrysler Sebring

1 Answer

2000 Sebring has no brake lights


it will not be a short a short would either blow fuses, cause fire, or leave the lights on all the time. I would say that the brake switch at the pedal will be your issue

Sep 05, 2009 | 2000 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...