Question about 1996 Toyota Land Cruiser

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings

Need head bolt torque and cam shaft torque settings

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 956 Answers

Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Posted on Nov 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: need to find specks on cylingder head for 1996 toyota tercel

The cylinder head bolt torque is a 2 step process.

First: Torque all of the bolts to 45 Nm (450 Kgf-cm or 33 ft lbs.)
Replace any head bolt that will not torque to the above specs.

Second: after all ten bolts are torqued to the above specs, the head bolts are then "Torqued to Distance"...

Starting at the center bolts, retorque all ten bolts an additional 90 degrees.

Hope this helps, the graciousness of a FixYa rating would be greatly appreciated.

Posted on Jan 21, 2009

freetek
  • 5568 Answers

SOURCE: bolt torque specs

I have used Haynes service manuals for (hate to admit it) many decades and I recommend you check to see if this one:

http://www.amazon.com/Haynes-Toyota-Automotive-Repair-Manual/dp/1563923513

doesn't cover your engine.

I have found darned few 'holes' in their coverage.

Auto parts stores carry these and I suspect that even though sealed, the sales people will not give you too hard of a time if you explain you want to insure you are getting what you need.

Haynes is not the same as it was 20 years ago before they were acquired by Chilton but the price/utility ratio is still pretty good.
Mostly I'm annoyed by the move to cheaper paper (newsprint)that is fussier, picks up dirt, tears more easily than the better paper of yore.

Posted on Aug 20, 2008

  • 1 Answer

SOURCE: Suzuki Vitara 1996 V6 2L assembly problems

The suzukiinfo.com site has a whole heap of free genuine manuals you can download and print out.
www.suzukiinfo.com

Posted on Jan 22, 2009

SOURCE: hyundai elantra 1.6GLS J2 torque settings

dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm

Posted on Sep 23, 2009

Boole5555
  • 160 Answers

SOURCE: broken sub tank switch in 80 series toyota landcruiser

Replace it. Most switches are mounted to plastic snap clips than can be removed with a simple Flathead screwdriver.A $5 plastic pry tool set is the best, but a butter knife or two works wonders sometimes.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many stages and what neuton meters are there for tightening head bolts?


Read this:

http://www.scribd.com/doc/52122956/Toyota-Landcruiser-Engine-Manual-2H-12HT

Aug 02, 2014 | Toyota LandCruiser Cars & Trucks

1 Answer

I need to know what torque i have to use to tight head bolt


-difference car with different torque. You need to look in its repair manual.

Good Luck

Mai

Nov 12, 2013 | 2006 Toyota Land Cruiser

1 Answer

What are the torque bolt sequence and tolerance intructions for 1995 Toyota Carina E GT


Hi Info, It would help to know the engine fitted into the vehicle. If it is the "S" or "A"series the torque setting is 29 nm. Once set to 29 nm paint each head of each bolt with a dot of white or easily seen paint. The dot should be facing the front of the engine. Tighten each cylinder head bolt an additional 90 degrees, until all are facing the side of the engine. Once complete follow with an additional 90 degrees, so that all paint marks are facing the rear of the engine. The tightening sequence begins at the center of the engine and follows a spiral pattern outwards. Something many people do not know with these engines is that the camshaft needs to be tensioned before fitting it. The shaft gear which has has two sections must be pre loaded and locked before setting it to the match marks to align the two cams. If the engine overheated it is always good policy to have the head checked by an engineering company for warpage before fitting it back. Regards John

Dec 22, 2012 | Toyota Cars & Trucks

1 Answer

Engine torque settings


Commonly Asked Torque Specs in foot pounds
The main bolts have a torque of 76 lb.-feet and the cylinder head bolts have 62 lb.-feet of torque. The cylinder head studs have 70 foot-lbs of torque, the cam timing gear have lb.-feet of torque, and the cam bearing bolt has 14 lb.-feet of torque.

Crankshaft Torque Specs
  • The stock rod bolts have 46 lb.-feet of torque and the ARP rod bolts have 50 lb.-feet of torque. The crankshaft pulley has 116 lb.-feet of torque, while the flywheel has 80 lb.-feet of torque.


Other Torque Specs
  • The intake manifold and exhaust manifold have 33 lb.-feet of torque each and the oil pan bolts have 9 lb.-feet of torque. The cam timing gear has 58 lb.-feet of torque and the cam bearing bolt has 14 lb.-feet of torque. One set of timing cover bolts have 9 lb.-feet of torque and another set has 29 lb.-feet of torque

Nov 07, 2012 | 1994 Toyota Corolla

1 Answer

Toyota Landcruiser 1991 80 series had a clunk when you change gears??


CHECK FOR LOOSE DRIVE SHAFT BOLTS OR YOU COULD HAVE WORN UNIVERSAL JOINT BEARINGS.

May 16, 2011 | 1991 Toyota Land Cruiser

1 Answer

Toyota Landcruiser drops out of/back into overdrive repeatedly


transmission servos sticking or bad valve body.take to trans shop for free diagnosis,most shops will do it for free.

Sep 24, 2009 | 1996 Toyota Land Cruiser

1 Answer

I need the torque settings for a 1996 1400cc megane


oil filled cam followers ,dont forget to squeeze oil out before refitting so they can re adjust.head bolts about 80 will suffice

Apr 12, 2009 | Renault Sportwagon Cars & Trucks

1 Answer

Blown head gasket on a 1983 toyota tercel


The head bolt torque is 48ft. pounds and the camshaft bolts are 16ft. pounds thats for a 1.5L S.O.H.C motor.

Dec 03, 2008 | 1983 Toyota Corolla Tercel

Not finding what you are looking for?
1996 Toyota Land Cruiser Logo

629 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...