Question about 2007 GMC Canyon Crew

1 Answer

How do i errase the message change oil .i did change the oil last week and the message is till there tank you

Turn off the switch press brakes and turn on switch.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 579 Answers

I hope this procedure works for your vehicle. Put your key into ignition, turn ignition to ON, and press your gas pedal to the floor three times. I think this is the standard way on General Motors vehicles. GOOD LUCK FRIEND.

Posted on Nov 22, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I clear a service emissions message on a 2005 Mercury Mariner with a 3.0L engine. I have performed the required maintenance procedures at both 30,9000090's and 60,000miles. Still have message.


Warning Messages The warning messages can interrupt the display until cleared or reset by the driver. The warning messages are either single cycle, non-resettable, or repetitive warning messages.
The single cycle warning messages display once whenever the ignition switch is turned to the ON position or a fault occurs in a system, and can be cleared by pressing the RESET button. The single cycle warning messages are:
  • liftgate ajar
  • liftgate glass ajar
  • service emission system
  • low brake fluid
  • service brake system
  • check left headlamp
  • check right headlamp
  • check left turn lamps
  • check right turn lamps
  • check left high beam
  • check right high beam
  • check brake lamps
  • check parking lamps
  • washer fluid low
  • check fuel cap
  • change oil soon
  • change oil now
  • low fuel
  • service 4x4
  • turn signal on

Jun 15, 2016 | Mercury Cars & Trucks

1 Answer

Excessive fuel consumption


Does it drive normally? Or harder to get it moving? Are the tires all on the low side? Could your brakes be dragging or calipers seizing up?

Jan 24, 2015 | Cars & Trucks

1 Answer

How reset oil change light 2011 charger


Your vehicle is equipped with an engine oil change
indicator system. The "Oil Change Due" message will
flash in the EVIC display for approximately 10 seconds
after a single chime has sounded to indicate the next
scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.

Unless reset, this message will continue to display each
time you cycle the ignition to the ON/RUN position. To
turn off the message temporarily, press and release the
MENU button. To reset the oil change indicator system
(after performing the scheduled maintenance), perform
the following procedure:

1. Without pressing the brake pedal, push the ENGINE
START/STOP button and cycle the ignition to the ON/
RUN position (Do not start the engine.)

2. Fully depress the accelerator pedal, slowly, three times
within 10 seconds.

3. Without pressing the brake pedal, push the ENGINE
START/STOP button once to return the ignition to the
OFF/LOCK position.

NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.

Source: Owner's Manual page 293

Dodge Charger Owners Manual

Oct 04, 2013 | 2011 Dodge Charger

1 Answer

How to turn of change engine oil light on 2011 ford focus


From FocusFanatics online - -

Resetting the oil life monitoring system
1. Turn the ignition key to the on position. Do not start the engine.
For vehicles with push-button start, press and hold the START/STOP
button for two seconds without pressing the brake pedal. Do not attempt
to start the engine.
2. Press both the accelerator and brake pedals at the same time.
3. Keep both pedals fully pressed.
4. After three seconds, the Service: Oil reset in prog. message will be
displayed.
5. After 25 seconds, the Service: Oil reset complete message will be
displayed.
6. Release both the accelerator and brake pedals.
7. The Service: Oil reset complete message will no longer be
displayed.
8. Rotate the key to the off position.
For vehicles with push-button start, press the START/STOP button to
turn the vehicle off completely.

Jul 07, 2012 | Ford Cars & Trucks

1 Answer

Reset after oil change


AnswerEasy get an oil change at a garage and have them erase the code or do the oil change your self and then disconnect the neg battary terminal. Easier AnswerOn the console, where the oil change light is on, scroll through the items until you get to oil life. Once at oil life, hold the reset button and it will say Engin oil new? Press reset again and this should set you oil life back to 100% without needing to disconnect your battery

Complete Answer
1- Turn on the ignition without starting the car
2- You will get warning messages on the display (including the "change oil soon" or "oil change required" message) press reset for each warning till you get the Odometer displayed.
3- press the setup button until "press reset for system check" appears
4- hit the reset button (need to do this fairly quickly, if you end up back at the odometer go back to step 3)
5- the system will scroll through the different things that are wrong that it has detected, you should go to "oil life XX%, Hold Rest New" message first if nothing else more major has been detected. When on this message hold the reset down unit you get the message "if new oil hold reset".
6 - hold the reset down till the message "oil life set to 100%" appears (note have seen different wording in some models)
7 - system should scroll through any remaining messages and then return to the odometer reading
Switch the car off and on and confirm that the message does not reappear. Have seen some instances where will not reset, if so take to your dealer.

Read more: http://wiki.answers.com/Q/How_do_you_reset_the_'Change_Oil_Soon'_light_in_a_2002_Ford_Explorer_or_Mercury_Mountaineer#ixzz1GbI0wIQ9

Mar 14, 2011 | 2004 Mercury Mountaineer

3 Answers

How do I reset the oil life indicator on 2006 Saab 9-3


Switch ignition ON. Press brake pedal. Press button [A]. RHD - 100248. LHD - 100254. Turn button [B], until the message "System Settings" is displayed. Press button [B]. Turn button [B] until the message "Service Info" is displayed. Press button [B]. The message "% left of oil quality/days to service" is displayed. Turn button [B] until the message "Reset Service Ind." is displayed. Press button [B]. The message "Are you sure? Yes or No" is displayed. Turn button [B] to select "Yes". Press button [B]. The message "service parameters updated" is displayed. Switch ignition OFF.
BUTTON B IS ROUND PUSH/TURN BUTTON
BUTTON A IS TWO DOWN FROM THIS

May 08, 2010 | 2001 Saab 9-3

3 Answers

Reset change engine oil light 2009 ford escape xlt


This is how it works on my 2010 Escape. There are 3 buttons to the lower left of your steering column (Info, Setup, and Reset):
1) when it's displaying the "oil change required" message, hit the "reset" button to get rid of the message2) then hit the "Setup" button twice and you'll see the "oil life" screen, which is now at "0%". It tells you what to do next (i.e. "hold reset" until it say 100%).

Mar 14, 2010 | Ford Escape Cars & Trucks

3 Answers

2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on


Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Apr 02, 2009 | 2007 Ford Explorer Sport Trac

1 Answer

BLINKING SERVICE OIL MESSAGE


it seems like that who ever serviced the vehicle forgot to reset the service indicator. Try and reset this service indicator yourself . Button B below rev counter
Button A below speedo
press and hold button A, switch on ignition release button A turn button b to the right to reset display switch ignition off. I hope this solves your problem.

Sep 04, 2008 | 2001 Volkswagen Golf

Not finding what you are looking for?
2007 GMC Canyon Crew Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...