Question about Cars & Trucks

1 Answer

WOULD A FAULTY VSS CAUSE THE CAR TO CUT OUT WHEN PULLING UP AFTER THE THROTTLE IS RELEASED.

I HAVE REPLACED THE IDLE SPEED SENSOR.

Posted by on

  • mick proudman Nov 22, 2014

    COULD REPLACING THE CAR BATTERY ALSO CAUSE THIS TO HAPPEN

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 22,095 Answers

More like a faulty EGR valve ,make a gasket from a coca cola can and block it off then try it

Posted on Nov 22, 2014

Testimonial: "Hi,thanks,I will let you know how I get on.one thing,this is a petrol model,does it have a egr valve?"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2011. Why has cruise control failed?


cruise controls are controlled by several units
VSS or road speed sensor, clutch and brake sensors , engine speed (tacho) and the on/off switch
cruise controls will disengage automatically if the road speed is too slow ( higher for manuals than autos ) so if the road speed is below around 20mph it may not engage at all as the VSS says it is too slow for the engine rpms
check all sensors for adjustment

Aug 30, 2015 | Jeep Liberty Cars & Trucks

1 Answer

Transit van cutting out


Okay, no codes and cut out and low idle,

I have seen this on many types of cars and trucks, first have the tech clean the throttle body, make sure he uses a good cleaner and tooth brush, open the plate with his fingers and brush carbon build up off throttle body and plate then rinse clean with throttle body cleaner, next check and clean mass air flow sensor ,

What happens is the throttle plate when closed allows a small amount of air to pass, after time carbon build up closes the gap little more causing lower idle at stops or when gas pedal released in turn causes engine stall at times, the mass air flow sensor also can cause a problem when diodes that read air flow get dirty and allows air to enter without computer knowing and causes lean condition,

Aug 12, 2012 | Cars & Trucks

2 Answers

I have replaced my fuel pump, filter, throttle position sensor, and relay on my 1992 jimmy. it runs but everytime it hits idle speed it cuts off. what could that be


It should have an idle air control valve which lets air into the intake to control the idle speed. The valve could be faulty, or dirty, or the throttle body could be dirty. The computer opens and closes the valve to regulate idle speed.

Jul 16, 2012 | 1992 GMC Jimmy

1 Answer

Faulty speedometer


Hi there:
This is a common problem on Mazda, it is usually caused by a faulty vehicle speed sensor. I would take a look at the wiring and connector to the vehicle speed sensor. If the wiring and connector look to be in good condition, replace the vehicle speed sensor. The sensor is on the transmission near the cv axle. It is held in by one bolt.
VEHICLE SPEED SENSOR (VSS) REMOVAL/INSTALLATION Disconnect the negative battery cable.Disconnect the VSS connector.
3_19_2012_3_49_05_pm.gif
Remove the VSS.Apply ATF to a new O-ring and install it on a new VSS.Install the VSS. Tightening torque7.9 - 10.7 Nm (80 - 110 kgf.cm, 69.5 - 95.4 inch lbs.) Connect the VSS connector.Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Mar 19, 2012 | Mazda Protege Cars & Trucks

1 Answer

Speedometer faulty


Hi there:

This is a common problem on Mazda, it is usually caused by a faulty vehicle speed sensor. I would take a look at the wiring and connector to the vehicle speed sensor. If the wiring and connector look to be in good condition, replace the vehicle speed sensor. The sensor is on the transmission near the cv axle. It is held in by one bolt.
VEHICLE SPEED SENSOR (VSS) REMOVAL/INSTALLATION Disconnect the negative battery cable.Disconnect the VSS connector.
3_19_2012_3_49_05_pm.gif
Remove the VSS.Apply ATF to a new O-ring and install it on a new VSS.Install the VSS. Tightening torque7.9 - 10.7 Nm (80 - 110 kgf.cm, 69.5 - 95.4 inch lbs.) Connect the VSS connector.Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Mar 19, 2012 | Cars & Trucks

1 Answer

Hyundai Tucson - engine loses power whilst driving, it does not cut out completely. Sometimes also struggling at idle


The drivability issue you describe has a multitude of possible causes. The best advice I can give you is that you take/tow the vehicle to the local/nearest Hyundai Service Department and have it properly diagnosed. Possible causes:
#1. Fuel delivery (Fuel Pump pressure, Injector(s) clogged/leaking)
#2. Vacuum Leak(s)
#3. Faulty Throttle Position Sensor (TPS)
#4. Electrical (Wiring)
#5. Faulty Sensors (Crank Position Sensor, Cam Position Sensor, Idle Speed Control Actuator, Faulty Manifold Absolute Pressure Sensor, etc.)
#6. Contaminated Fuel
#7. Faulty Powertrain Control Module (PCM)
Best advice, get is properly diagnosed.

Jun 10, 2011 | Hyundai Tucson Cars & Trucks

1 Answer

Hi i have a 1999 ford cougar and the speedo is faulty sumtimes it works n sometimes it dont wen it doesnt it idles irraticly and sumtimes cuts out wot could this be?


I think you may have a faulty vehicle speed sensor (VSS). It is located in the transmission behind the engine. It does control the speedometer and the computer uses the speed signal to adjust fuel. You would really need someone to attach a scan too and look at the vss readings to see if they are erratic.

Apr 03, 2010 | 1999 Ford Escort

1 Answer

What problems could a 2005 ford focus have if it cuts off at stops?


1 Inspect Spark Plug Incorrectly Gapped or Fouled Spark Plug(s). 2 Inspect Throttle Position Sensor Faulty or Incorrectly Adjusted/Connected Throttle Position Sensor. 3 Inspect Idle Air Control Valve Damaged, Loose, or Faulty Idle Air Control Valve. 4 Inspect Idle Speed Actuator Damaged, Loose, or Faulty Idle Speed Actuator. 5 Inspect Idle Stop Solenoid Damaged, Loose, or Faulty Idle Stop Solenoid

Sep 01, 2009 | 2005 Ford Focus

2 Answers

2002 f250 v10 engine quits after warm up at idle only


DTC = P0720
footnote b = MIL (malfunction indicator light) comes on after 2nd occurance
footnote c = tranny control indicator light (TCIL) flashes
circuit = OSS = output shaft speed sensor in the tranny (not the variable speed sensor (VSS) in the diff).
condition = OSS sensor circuit malfunction
probable causes = Short/open circuit, sensor, PCM

My guess? Replacing the OSS will take care of it. smile.gif I hope you don't have a faulty PCM. frown.gif

Mar 09, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Need to find out what color the vss wire is under hood


you don't have a vehicle speed sensor (VSS). You have a wheel speed sensor that tells the PCM vehcile speed in place of the VSS. What are you tring to do?
------------------------------------------------------------------------------------
The electronic engine controls consist of the following:
  • powertrain control module (PCM) (12A650)
  • throttle position sensor
  • idle air control valve
  • camshaft position sensor
  • crankshaft position sensor
  • mass air flow sensor
  • intake air temperature sensor
  • heated oxygen sensor—front
  • heated oxygen sensor—rear
  • knock sensor
  • cylinder head temperature (CHT) sensor
  • power steering pressure (PSP) switch
  • Wheel speed sensor
The powertrain control module needs the following inputs to calibrate the engine properly:
  • camshaft position
  • engine rpm
  • engine coolant temperature
  • amount of engine detonat

Feb 28, 2009 | 1999 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...