Question about Cars & Trucks

1 Answer

How to remove back to fit battery - Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

On some vehicles theres a tray that the battery sits on. These trays can be removed or the battery tie down bar can also be removed to fit the battery in place. If you are not able to place the tie down back in place you can use a bundgy cord to hold the battery in place. First you hook the cord into the vehicle before you place the in, make sure the hook part is not going to touch the battery bcaz it might puncture the battrry or wear a hole in the battery. So then u should make sure the strap or cord is not too lose and attach the other side so it will be safely secured in your vehicle. Preferably rubber, so if this helped you please give me credit for answering your question.

Posted on Nov 22, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How dowe fit a new leasure battery onour camper van please how dowe remove thepassengerseat


dont believe the design would make you unbolt the chair and remove it

will be either by sliding the chair right back
look for releasing the metal clips catches at the floor pan
as the chair is moved right back
then maybe tilting



26212407-oaabsiacwf3ritpak1e5e5z5-2-0.jpg

Jun 04, 2016 | Cars & Trucks

1 Answer

My car battery went dead, bought a new one, every time I hook up positive cable, car alarm goes off........


remove alarm reinstall after fitting. at least cut power supply and back up supply fit battery repair reinstall alarm.

Feb 16, 2015 | 2004 Dodge Stratus

1 Answer

How to change a battery in a 96 volvo850


undo the negative on the battery. ( immobilizer model) turn key to number 2 on the ignition as you would if starting the engine, then turn off back to 0. now you have 30 seconds to pull the negative lead off. with lead off push and support the wire to the side out of the way of the battery, then remove the positive lead from the battery and do the same to this wire as the negative move out of the way. Now you can remove the battery holding bracket or bolt. spray some wd40 on this before you start. remove the battery and check that the cage that the battery is in good condition any rust clean up and spray a new coat of paint on it. ( I usually put an old carrier bag on there if there is no plastic tray fitted, or a garden bag as so it will cover the battery when fitted.) when all clean and ready for the battery put the battery back in and secure it back down. then connect the positive lead I usually put some grease on the battery poles before refitting helps stop the battery being eaten by its self. then after this is done connect the negative it will spark but don't worry about this as it will do, secure the bolt down and cover over the battery if you have one or made one. now depending if you have the original radio fitted you will need to put the code back in to the radio. and after this is done the battery has be done now. just the time etc to be done if you want to engine sould start as normal.

May 06, 2014 | 1994 Volvo 850

1 Answer

How do i remove the battery of a 2008 Chrysler Sebring to put a new one


First thing get the code to the radio so that you can turn the radio back on . Turn everything off . Disconnect the earth lead off then the positive lead. Remove the battery hold down strap /clamp and lift battery out. Ensure that the replacement battery has the same poles in the same places or the leads may not fit correctly. Place the battery in position and fit the hold down clamp/strap. Fit positive lead after ensuring that the terminal is shiny clean inside. Fit earth lead after cleaning the terminal . Tighten clamps securely. Turn igniting on and wait a few minutes for the CPU to reprogram. Start engine and wait for the ECM to sort out any losses from the battery removal.. If there are lights tha stay on it may be necessary to have a code reader used to reset the CPU

Oct 24, 2013 | 2008 Chrysler Sebring

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

1 Answer

How change 02 sensor


Remove negative pole wire from your battery, disconnect O2 Sensor wire harness plug connector remove O2 sensor fit lubricant only on the thread fit it back connect connector and battery and start the engine.

Sep 25, 2012 | 1997 BMW 328

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

How do you change a positve battery cable on a 1998 dodge avenger car?


First a little more clarification would be helpful in, Why do you think the cable needs replaced? If the cable is corroded at terminal connection a new connection fitting is much more simpler than cable replacement. Nonetheless, remove the negative battery cable first, then the positive. (1)Clean the corroded area's with baking soda and water mixture (you should wear eye and hand protection- battery acid will eat through clothing in a matter of minutes).Scrub gently with nylon brush -using a wire brush can cause sparks and may cause a fire from hydrogen gas escaping form battery. Flush with clean water and your ready to start the next process. (2)Assuming you will adding a new terminal connection fitting - cut off bad fitting with wire cutters or hack saw, skin back wire about ONE inch and install new cable fitting.(3) install / reconnect battery. (4) Your cars computer will be cleared of all learned shifting patterns and other feedback information. It will revert back to factory preprogrammed settings. Average cost of replacement cable clamp $3.50. New cable cost to starter +$30.00

Happy motoring.

Jan 03, 2011 | 1998 Dodge Avenger

1 Answer

Battery light on console is intermittent


Sounds like the alternator is going faulty. There is a brush inside the alternator that wears over time. If you are capable, you can remove the battery, remove the wires from teh alternator, loosen and remove the dive belt, and remove the alternator. Take it to an auto electrician to be rebuilt, or buy a replacement and fit back in.

Nov 09, 2010 | 1994 Toyota Camry

3 Answers

Aston Martin Vanquish Flat Battery


There's a relatively easy answer.
You were told correctly that you have to take out the back seats.
This is easy.
Between the lower cushion parts of the back seats is a small, cucumber size piece of leather trim, this you simply pull out.
Under this are some manually screwed in bolts, a bit like the dials on your old car radio, take them out, then juggle out the lower cushions.
On fitting they're kind of pushed under the side panels (under the window) so you have to pull hard.
Next there are a couple of bolts holding the backrest in place, these are at the bottom of the backrest, remove.
You only need to remove the RH backrest. (Right hand means on the left if you're facing backwards).
After these are out all that holds the backrest is a spring 'jaw'.
To explain how this works, let me explain something.
Before the seats were in, if you were fitting the backrest and you were kneeling in the car, looking at the metal (body) backrest support you would see a 2" x 2" hole in the Body.
On the back of your seat panel is a large metal clip, it works a bit like a big paper clip.
This slides upwards into the metal body (hole) behind to fit, down to take the backrest out, so slide the seat panel downwards.
Now the seats are out.
Here you will see a handle like on a car bonnet release. Pull it, voila.
I had a similar charging availability problem to yours last year, all I did was about once a week, parked the car on the drive (overnight at least), put it on charge, gathered the cable to the right hand rear boot corner where there's plently of clearance then locked the boot.
You won't damage the wire, just trap it in the seal.
My battery never went flat once.
If you haven't got a drive do it at a friends.
Good luck.

Jul 25, 2009 | 2004 Aston Martin Vanquish

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...