Question about Cars & Trucks

1 Answer

Hi,I have a problem with my 1.3 ford bantam 2006 model it keeps jerking and when you drive it it feels as if it looses power for a couple of seconds then kicks back. Help please

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 61 Answers

Timing Belt jumped a notch, or a plugs not firing correctly, or fuel starvation, try plugs first.

Posted on Nov 22, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 37 Answers

SOURCE: 2001 Audi A6

HAVE YOUR VACUUM LINES CHECKED AND INTAKE HOSES

Posted on Apr 06, 2009

  • 14036 Answers

SOURCE: Steering hard /loosing pwer at 40-55mph

check power steering hoses. for leak it sound like fluid getting on belt causing slipping.causing alternator problems.alternator cant charge if belt slipping.fluid getting on exhaust manifold making it smoke it also can catch fire.so look at power steering pressure hose sound like it rupture causing lost fluid and hard steering.

Posted on May 20, 2009

jaysonemanme
  • 500 Answers

SOURCE: 1995 crown vic gear problems/gear shift wont lock

most likely the shift tube bushings are bad- you may have also lost a few screws in the shift tube or they could just be loose. you have to pull the steernig column down to inspect/repair it.

Posted on May 31, 2009

BCAS1298
  • 3092 Answers

SOURCE: 1996 ford ranger ac compressor keeps kicking on

It's just low on freon, low pressure switch will cut a/c compr off and on, so it won't get damage a/c compr. due to low on freon, recharge it you'll be fine.

Posted on Jul 08, 2010

  • 1 Answer

SOURCE: I have ford bantam 1.6i rocam 2006 model. It Doesn't start, It doesn't pump the petrol, the is no power to fuel pump

Refer to your manual there is a switch that deactivated the fuel pump in case of accident, there is a switch by the pasangers feet that if in the up position is activated to stop the fuel...

Posted on Aug 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

When I drive with speed of 100 this car twist at back.what could be the problem?


There are 3 Adjustments for front allinement
Camber Castor and toe in
get them checked .

Dec 03, 2014 | 2005 Ford Bantam 1.3i

1 Answer

I got a ford bantam bakkie. Wen I drive and comes to stoping, so I brake and gear down to 2nd. If I should pull away in 2nd the bakkie either jerks or the revs feels a bit delayed. Question is can it be a...


sounds to me like the clutch plate is just a little worn. its a good way to test a clutch take off in 1st, 2nd on clutch power and see how it responds.

Jul 23, 2014 | Cars & Trucks

1 Answer

Ford Bantam rocam Clutch: How do I bleed the clutch?


Clutch bleeding on hydraulic slave cylinders are done in the exact same method as regular hydraulic brakes. If the slave cylinder has a separate reservoir, make sure it is above "MINIMUM" at all times. If it does not have a separate reservoir, then it works together with the master cylinder for the brakes, make sure that one is above minimum too. Pump the clutch pedal a couple of times (note you will rarely feel any resistance in the pedal), hold the pedal down, and have someone open the bleeder valve on the slave cylinder. Close it when no more fluid comes out with pressure, then rinse and repeat until the clutch pedal feels ok.

Jan 09, 2014 | 2006 Ford Bantam 1.6i

1 Answer

Ford problems


check iac valve or one cylinder misfire

Dec 19, 2013 | Cars & Trucks

2 Answers

I have ford bantam 1.6i rocam 2006 model. It Doesn't start, It doesn't pump the petrol, the is no power to fuel pump


Refer to your manual there is a switch that deactivated the fuel pump in case of accident, there is a switch by the pasangers feet that if in the up position is activated to stop the fuel...

Aug 28, 2012 | 2006 Ford Bantam 1.6i

1 Answer

Ford 7.3 hard start only when engine is cold


Check to see if there is power to the glow plugs when the key is switched to the on position.

Jan 09, 2009 | 1997 Ford F350 Crew Cab

1 Answer

Jerking when keeping speed stablized at any speed


Or you could just buy a couple bottles of gas line antifreeze and try that. add one right away and one at your next fill up.

Dec 18, 2008 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...