Question about Cars & Trucks

1 Answer

What order do I torque the head bolts in on my 2002 pt cursier

Getting ready torque head bolts

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 299 Answers

Four steps torque all to 25 then torque to 50 then redo the 50 ft/lb then , last step turn all bolt 90 degrees or a quarter turn this is the order for this
10 6 2 3 7
9 5 1 4 8

have a good day

Posted on Nov 22, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: how to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Which motor?

Posted on Sep 04, 2008

  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 7353 Answers

SOURCE: head bolts torque settings for dogde neon 2002

assuming this is the "C" engine 8th digit on VIN plate. Use new bolts. torque first step to 25lbs, 2nd 50lbs, then 3rd 50lbs, then 1/4 turn.

Posted on Sep 23, 2009

  • 1861 Answers

SOURCE: need torque specs for a 2002 toyota camry 2.4 for

The 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.

We hope that this helps you out.

Posted on Dec 29, 2009

  • 36 Answers

SOURCE: I need head bolt torque sequence for 2002 nissan

So 80 degrees is approx. how many ft lbs.

Posted on Jun 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can anyone.tell me the Torqe specs for a 2004 or cruiser


Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

Jan 18, 2016 | Cars & Trucks

1 Answer

How to install the cam shaft had to remove to put head bolts in my 2002 pt crusier


Get a Chiltons/Haynes manual that covers the year/make/model or your car. It has entire section on rebuilding the engine and will give you torque specs, camshaft R/R, etc. Hmmm Having to take a camshaft out to put in head bolts does not seem to be one of Chrysler's better ideas.

Nov 22, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Head bolt torque yield


90% of head bolts are stretched when installed. If you have the torque settings, you can confirm this by checking the specs. If it says example, 90lbs feet, plus a quarter turn, this confirms they are gonna stretch once torqued.
In any case, yes, change those head bolts at all costs. DO NOT RE-USE THEM. Make sure to torque and in the order as well. do not use a random pattern when torqueing.

Nov 01, 2013 | 2002 Jeep Liberty

1 Answer

I need to know how to find/set timing marks for 2002 Kia Sedona and head bolt torque specs


The head bolt torque on a 2002 Kia Optima is 45 ft/lbs of torque. Always make sure you use a good torque wrench to get it right. ------------------------------------------------------------------------------------
Original Launch X431 Master

Mar 13, 2013 | Cars & Trucks

1 Answer

Torque the cylinder head bolts for mitsubishi lancer 2002


Try this
I dont know which engine you have.

420a
1. Torque all center bolts to 25 ft-lbs, torque the 4 corner bolts to 25 ft-lbs
2. Torque all center bolts to 50 ft-lbs, torque the 4 corner bolts to 50 ft-lbs
3. Re-Torque all center bolts to 50 ft-lbs, re-torque the 4 corner bolts to 50 ft-lbs
4. Tighten all bolts in the sequence from #1-#10 an additional 1/4 turn.

7-Bolt 4G63
1. Torque all bolt to 58 ft-lbs in order
2. Loosen all bolts completely to 0 ft-lbs
3. Torque all bolts to 15 ft-lbs in order
4. Tighten all bolt 1/4 turn in order
5. Tighten all bolts an additional 1/4 turn in order.

ARP Head Studs
1. Tighten all bolts to 40 ft-lbs
2. Tighten in steps of 10 ft-lbs increments until the specified torque that you are looking for is reached. This can vary with the amount of boost you plan on running.

Jun 30, 2011 | 2002 Mitsubishi Lancer

1 Answer

I need to find the torque specs for the connecting piston rod? also the sequence and torque for the cylinder head bolts this is for a kia rio 2004 6cyl


22 - 24 ft. lbs. for the rod caps and....
110795143Cylinder Head Tightening Torque and Sequence.

Tighten cylinder head bolts in order shown.
Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

Loosen bolts in reverse of order shown.

Retighten cylinder head bolts in order shown.
Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

Mark cylinder head bolts for rotational reference.
Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

CAUTION:
  • Do not reuse the old cylinder head bolts.

May 31, 2010 | 2004 Kia Rio

1 Answer

What is the torque spec for the head bolts on a 2004 optima with the 2.4L?


1st - step; - 25 ft./lbs.

2nd - step; - 50 ft./lbs.

3rd - step; - 50 ft./lbs.

4th - step; - turn 90 degrees
Torque the bolts in this order (looking at the heads)

10-6-2-3-7
9-5-1-4-8

Feb 25, 2010 | 2002 Kia Optima

1 Answer

Need torque specs for a 2002 toyota camry 2.4 for the head bolts


The 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.

We hope that this helps you out.

Dec 29, 2009 | 2002 Toyota Camry

1 Answer

2000 2.0 petrol pt cruiser head bolt torque?


Use a torque wrench to tighten the bolts in the following order:
  1. Tighten all center bolts to 34 Nm (25 ft.-lbs.).
  2. Tighten the four corner bolts to 27 Nm (20 ft.-lbs.).
  3. Tighten all center bolts to 68 Nm (50 ft.-lbs.).
  4. Tighten the four corner bolts to 47 Nm (35 ft.-lbs.).
  5. Retighten all bolts a second time to the same specifications in step 4 to double-check torque.
  6. Finish by tightening all bolts an additional 1/4 turn.

Nov 11, 2009 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...