Question about 2006 Volvo XC90

1 Answer

Headlamp? kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk baffle socket ballast fuses switch ppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppp

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volvo Master
  • 14,585 Answers

Probably just a bad bulb.

Posted on Nov 22, 2014


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the headlight housing on my 1999 lumina


Raise the hood.
Lift the flap on the appropriate end of the radiator upper air deflector.
Separate the radiator side air baffle from the upper air deflector.
Remove the fastener retaining the upper edge of the front bumper fascia to the headlamp bracket.
Remove the two bolts retaining the headlamp assembly to the headlamp bracket.
Slide the headlamp assembly slightly inboard to release the outboard retaining tabs. Carefully pull the upper edge of the front bumper fascia away from the inboard edge of the headlamp assembly enough to aid in headlamp removal. Carefully remove the headlamp assembly from headlamp bracket.

Nov 22, 2014 | 1999 Chevrolet Lumina

1 Answer

2005 Lexus Rx330 Ballast problem??? First I saw my passenger side HID headlight was on and off and then mostly off. I thought the HID bulb burnt out. I bought a new one and replaced it. After I installed...


Well, we seem to have a real dilema here. I just searched the service manual for your 2005 RX330 and I cannot find any reference to a ballast for the HID headlamp bulbs. According to the wiring diagram, they are wired to the Headlamp Control Relays in Junction Block #2. (Right-hand side of the engine compartment) These relays are "Solid State", so my guess is that the balast for the HID may be built in to them. These are controlled by the Body Control Module. I would recommend scanning the body control module for fault codes before doing anything else. The first step in the diagnostic chart for the headlamp system is to perform a diagnostic systems check. There is a symptom chart to follow if there are no codes present, but if there are codes in the system, you could be shooting yourself in the foot trying to follow the symptom chart without first correcting any fault codes. This is not your fathers headlamp system - it is equipped with tracking control and automatic headlamp leveling...VERY sophisticated. Also lots of stuff that can break...this is what I call JOB-SECURITY- - LOL!

Apr 08, 2011 | 2005 Lexus RX330

1 Answer

Need help changing out the low beam on drivers side of 2006 buick rainier


Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.


  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
    counterclockwise.

To Install:


  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket
    clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)
gm-06-00-1591.gif




  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp
    assembly.
  6. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp
    assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)
gm-06-00-1590.gif




  1. Release the headlamp assembly retaining tabs.
  2. Disconnect the headlamp connector.
  3. Remove the park/turn bulb socket from the headlamp assembly.
  4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
    socket from the headlamp assembly.
  5. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
    socket into the headlamp assembly.
  3. Install the park/turn bulb socket into the headlamp assembly.
  4. Connect the headlamp connector.
  5. Lock the headlamp assembly retaining tabs.


prev.gif next.gif

Oct 28, 2010 | 2006 Buick Rainier

1 Answer

I need to change the headlights


REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

  1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
  2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
  3. Pull the headlamp assembly out and away from the vehicle
  4. Disconnect the headlamp electrical connector.
  5. Remove the headlamp assembly from the vehicle.
  6. Remove the headlamp bulb cover from the headlamp assembly.
  7. Remove the headlamp bulb socket from the headlamp assembly.
CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Remove the headlamp bulb.
  2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
  3. Remove the side marker bulb.
  4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
  5. Remove the parking lamp bulb.
INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Install the headlamp bulb to the socket.
  2. Install the headlamp bulb socket to the headlamp assembly.
  3. Install the headlamp bulb cover to the headlamp assembly.
  4. Install the side marker bulb to the socket.
  5. Install the side marker bulb socket to the headlamp assembly.
  6. Install the parking lamp bulb to the socket.
  7. Install the parking lamp socket to the headlamp assembly.
  8. Connect the headlamp electrical connector.
  9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
  10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.
NOTE: Refer to Fastener Notice in Service Precautions.
  1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
Tighten the bolts to 6 N.m (53 lb in).


  1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
  2. Close the hood.
3e4ca4a.gif

Oct 21, 2010 | 2006 Cadillac SRX

1 Answer

The nearside xenon headlamp does not work, i have fitted new bulb 2004 range rover


Hiya, if changing the bulb doesn't work it is probably the ignitor or the ballast. You can get a second hand set on the internet, just make sure to get the serial number right. If it is the ballast it is very easy to replace. For the headlamp on the left side as seen from sitting in the car it isn't even necessary to remove the headlamp. You can replace it just by unscrewing 3 torx screws and replace the ballast. If it is the other side you probably but not necessarily need to remove the headlamp which is also a piece of cake, see http://www.rangerovers.net/forum/viewtopic.php?f=2&t=31259&p=269733&hilit=headlamp#p269733
If it is the ignitor it is a bit more work since it is integrated inside the headlamp unit which you have to take apart to reach it. Chances are slim that it is the ignitor, the ballast is the weaker part and since it is purchased as a set I would recommend to try to replace the ballast first. Just make sure to switch off the lights and remove the key! It is dangerous because of high voltage!

Nov 07, 2009 | 2004 Land Rover Range Rover

1 Answer

Headlight replacement - 2002 Trailblazer


  1. Open and support the hood.Remove the grille.
  2. Pull up on the retaining tabs (1) in order to remove the headlamp assembly from the headlamp panel.
  3. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  4. Disconnect the headlamp electrical connector (2) from the headlamp assembly.
  5. Remove the side marker socket (4) from the headlamp assembly.
  6. Remove the park/turn socket (3) from the headlamp assembly.
  7. Remove the headlamp assembly from the headlamp panel.
  8. Installation:
  9. Position the headlamp assembly to the headlamp panel
  10. Index and seat the tabs on the park/turn socket (3) to the headlamp assembly.
  11. Index and seat the tabs on the side marker socket (4) to the headlamp assembly.
  12. Connect the headlamp electrical connector (2).
  13. Connect the headlamp leveling electrical connector to the motor/actuator if equipped.
  14. Align and install the 4 locator pins on the back of the headlamp assembly into the retaining tab holes.
  15. Push down on the retaining tabs (1) in order to lock the headlamp assembly into the headlamp panel.
  16. Install the grille. Refer to Grille Replacement .
  17. Close the hood

Oct 27, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

How to change lowbeam headlight bulb on 02 chev trailblazer


  1. Open and support the hood.
  2. Remove the grille.
  3. Pull up on the retaining tabs in order to remove the headlamp assembly from the headlamp panel.
  4. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  5. Disconnect the headlamp electrical connector from the headlamp assembly.
  6. Remove the side marker socket from the headlamp assembly.
  7. Remove the park/turn socket from the headlamp assembly.
  8. Remove the headlamp assembly from the headlamp panel.
  9. Remove the access cover from the rear of the headlamp.
  10. Disconnect the electrical connector from the socket.
  11. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  12. Disconnect the electrical connector from the socket.
  13. Remove the bulb and socket from the headlamp.
Replace the low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.


Oct 17, 2009 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Replace 1998 chevy lumina headlight assembly


Here are the steps:

  1. Raise the hood.
  2. Lift the flap on the appropriate end of the radiator upper air deflector.
  3. Separate the radiator side air baffle from the upper air deflector.
  4. Remove the fastener retaining the upper edge of the front bumper fascia to the headlamp bracket.
  5. Remove the two bolts retaining the headlamp assembly to the headlamp bracket.
  6. Slide the headlamp assembly slightly inboard to release the outboard retaining tabs.
  7. Carefully pull the upper edge of the front bumper fascia away from the inboard edge of the headlamp assembly, just enough to aid in headlamp removal.
  8. Carefully remove the headlamp assembly from the headlamp bracket.
  9. Disconnect the electrical connectors from the headlamp bulbs.
  10. Rotate the park/turn signal lamp socket counterclockwise to release.
  11. Remove the headlamp assembly.

Sep 06, 2009 | 1998 Chevrolet Lumina

1 Answer

How do i change both headlights on my 2002 chevy cavillier


Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Hood close out filler panel.
    • Bolts from the headlamp.
    • Headlamp from the headlamp mounting panel.
    • Electrical connector from the headlamp.
    • Headlamp bulb/socket retainer ring from the headlamp.
c218bc4.gif

  • Headlamp bulb/socket from the headlamp.
  • Bolts from the headlamp adjuster mechanism.
  • Headlamp adjuster mechanism.
  • To Install:
    1. Install or connect the following:
      • Headlamp bulb/socket to the headlamp.
      • Headlamp bulb/socket retainer ring to the headlamp.
      • Headlamp adjuster mechanism to the headlamp housing, if necessary
      • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
      • Electrical connector to the headlamp.
      • Headlamp to the headlamp mounting panel and lower mounting bracket.
      • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
      • Hood close out filler panel.

    Jun 06, 2009 | 2002 Chevrolet Cavalier Coupe

    1 Answer

    Installation of xenon light ballast


    you have to completely remove the headlamp install the kit and wiring, before you con remount the Headlamp.

    Jun 20, 2008 | BMW X7 Series Cars & Trucks

    Not finding what you are looking for?
    2006 Volvo XC90 Logo

    Related Topics:

    18 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volvo Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Volvo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...