Question about Cars & Trucks

1 Answer

Where is the slave cylinder on a 94 ford ranger

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 31 Answers

It is connected to the firewall.

Posted on Nov 22, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

  • 608 Answers

SOURCE: How do you replace the slave cylinder on a 1992 f150?

It is not usually necessary to replace the slave cylinder. Remove the cylinder and wash in metho. Exmine it for rust, pitting or grooving. If ok scuff the glaze from the cylinder walls with 320 grit w&d paper and more metho. Wash well with metho dry and fit a new kit of rubbers. Lubricate these with brake fluid ot rubber grease as you assembe. Refit the slave cylinder and bleed out the air. Job done.

Posted on Mar 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have to drop trans to install slave cylinder on 95 ford ranger


I know the regular sized Ford pickups had the slave cylinder inside the bellhousing, requiring transmission removal for replacement (not very smart, Ford!) So I suppose your Ranger, too, if you don't see the cylinder on the outside.; Most people who go through this replace the whole clutch and the slave cylinder at the same time, to avoid having to do it over again.

Nov 05, 2012 | Cars & Trucks

1 Answer

I need to replace my clutch slave cylinder in my 1993 ford ranger


the slave cylinder on the 90's models rangers is inside the transmission. you have to pull the transmission and its mounted around the output shaft highly recommended to replace the clutch since its out to save for troubles later

May 05, 2011 | Ford Ranger Cars & Trucks

1 Answer

I have a 94 ford ranger 4.0.. i've replaced the slave cylinder 2 times.. i put a new one in it and everytime about two weeks later it goes bad again and i have to keep putting fluid in it to get...


i am assuming you are talking about the clutch slave cylinder in either witch case you may have to more air in the lines try bleeding them until you get no air. the second thing i have noticed in stiff clutch's is that if there packed with dirt or what ever it may be to hard for the slave cylinder to move.

Feb 24, 2011 | Ford Ranger Cars & Trucks

1 Answer

How to install a slave cylinder on a 95 ford ranger


The easiest way to deal with this problem is to order the complete preblead slave cylinder kit.
You can, just go with a new slave cylinder but because of the age of the other parts. You may run into other problems down the road. Why have to do it twice.
To replace the slave cylinder only:
Its easy, just carefully push/remove the small metal pin that hold the plastic line to the slave cylinder. then push-in and turn counterclockwise, to remove slave cylinder. Then install new slave cylinder and reverse the procedure. Now bleeding the system will take a while. But all you will do is just keep pumping the clutch pedal until the pedal returns.

May 18, 2010 | 1995 Ford Ranger Supercab

1 Answer

How do I change the slave cylinder on 1993 ford raNGER


the slave cylinder is part of the throw out bearing,the transmision must be removed in order to gain access to it.

Apr 26, 2010 | 1993 Ford Ranger SuperCab

3 Answers

We have a 94 manual transmission Ford Ranger located in a cold climate. All of a sudden, when you step on the clutch pedal there is no resistance. Suggestions on what this might be?


you need to check the fluid level in the hydraulic clutch master cylinder under the hood,it is probably low or the slave cylinder in the bell housing that pushes the throw out bearing in is leaking.

Jan 18, 2010 | 1994 Ford Ranger Supercab

1 Answer

2006 ford ranger can not bead the slave cylinder


I dont want to make you feel silly but it seems like you loosened a grease nipple and not a bleed screw. A small amount of fluid (if the slave cylinder is not new) is normal. Their is no way grease can get into the fluid system. Take off the feed pipe to the slave cylinder Try pumping the pedal or use your vacuum pump from there.Get someone to pump the pedal holding your finger on the end of the pipe to see if their is any preasure comming that far if not its your master cylinder if you have preasure check the slave cylinder again for a bleed screw. It seems more like the master cylinder unless it ran out of fluid otherwise how did air get in. You should also check if the slave cylinder or the bar comming from it is adjustable Sometimes their is a screw on the bar others have oblong holes to move the slave cylinder back or forward

Aug 09, 2009 | 2006 Ford Ranger

2 Answers

Brake fluid in brand new 1989 ford ranger clutch slave


no it doesn't come filled basically you bleed it like a brake system. Fill the master cylinder and pump the clutch, there is a bleeder on the slave cylinder

Dec 08, 2008 | 1989 Ford Ranger

1 Answer

2001 ford ranger clutch


have you check the slave cylinder to see if its moving when someone puts there foot on the clutch.
And check the adjustment on the master cylinder.

Sep 18, 2008 | 2001 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...