Question about Cars & Trucks

2 Answers

How to replace a crankshaft sensor for chevrolet equinox 2005

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

It is located on the passenger side,behind the bottom/crankshaft pulley(called the harmonic balancer). Jack the car up and place jack stands under it (put the jacks back far enough not to interfere with the sub frame/ engine carriage),remove the drive belt, remove the tire, remove the inner fender covers, place the jack under the carriage, remove the bolts for the engine carriage on the passenger side, lower the jack and carriage, remove the bolt from the harmonic balancer, install a harmonic balancer removal tool, remove it. The sensor is right there. remove the two bolts and the electrical plug. Install in reverse order. On the harmonic balancer bolt, If you don't have an air impact gun you will have to remove the starter also. And use a flat long screw driver on the flywheel to hold it from moving.

Posted on Nov 22, 2014

Ad

Why should be the question

You have codes related?

Still have to component test, to find
a problem,unless your throwing parts
at the unknown

Lots of pictures on the internet where sensors are

Posted on Nov 22, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankshaft seal on a 2005 chevy equinox


If you're looking for the seal -have a look on Ebay:
1 042results for equinox crankshaft seal

If your question relates to a leak, a classic symptom of a leaking crankshaft seal is drips of oil from the bell housing - where the transmission attaches to the engine. It only leaks when the engine is running.

To replace the seal you need to remove the transmission/clutch/flywheel assembly -or in the case of auto transmission - the torque converter which attaches to the rear of the engine.

To remove the old seal you simply prise it out with a screwdriver, lubricate the new seal and gently tap it into position. However as mentioned, you need to remove the transmission first..

Oct 23, 2016 | 2005 Chevrolet Equinox

1 Answer

2005 chevy equinox abs and traction lights on


Is it causing any problems? If not, is the code popping back up after it's cleared?

Jan 01, 2014 | 2005 Chevrolet Equinox LT

2 Answers

What causes a P0036 code on a 2005 chevrolet colorado 2.8L?


P0336 - Crankshaft Position Sensor A Circuit Range/Performance


Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
Possible causes - Harness or connectors (The sensor circuit is open or shorted)
- Crankshaft position sensor may be faulty
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead (Weak) battery

Mar 03, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

My friends got an equinox is getting partial power while his vechile is off but his altenaor isnt bad. What can be the problem?


CHEVROLET EQUINOX 2005 Safety Report #10128539 CHEVROLET EQUINOX 2005 car safety problem was reported on July 11, 2005.CHEVROLET EQUINOX 2005, manufactured by GENERAL MOTORS CORP. had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . PURCHASED 2005 CHEVY EQUINOX ON MAY 26 2005 HAVE HAD IT AT THE DEALER 5 TIMES IN THE PAST 47 DAYS 1ST THE SUNROOF STOPPED WORKING, THEN THE TRANSAXLE OVERHEATING LIGHT CAME ON GOT THOSE "REPAIRED" DIDN'T GET OFF THE DEALERS LOT AND THE LIGHT CAME ON AGAIN THEY CHANGED SENSOR BROUGHT IT BACK THE NEXT DAY AND WAS TOLD THEY FOUND A CHAFFED WIRE IN THE MAIN HARNESS YESTERDAY I HAD IT TOWED IN AFTER ENGINE LIGHT AND TRACTION CONTROL LIGHT CAME ON FELT LIKE WHEELS DIDN'T WANT TO TURN AND ON HILLS HAD NO POWER TO CLIMB I LIVE IN THE MOUNTAINS OF PA WILL NEVER BUY ANOTHER CHEVY.Mileage was 2400 miles.Problem was reported in ALBRIGHTSVILLE, PA.
CHEVROLET EQUINOX 2005 Safety Report #10128539

Dec 17, 2010 | 2005 Chevrolet Equinox

3 Answers

I need a diagram of a 2005 Chevy Equinox engine


where is the coolant temp sensor on a 2005 chevy equinox

Aug 05, 2009 | 2005 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...