Question about 1996 Pontiac Grand Am

1 Answer

How to remove transmission from a 96 Pontiac grand am se

Posted by on

Ad

1 Answer

If that is front wheel drive, you need a lift
in a trans or repair shop

Nothing you can do at home

Posted on Nov 22, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
carytyree
  • 5 Answers

SOURCE: adding transmission fluid to a 2002 pontiac grand prix se

I am not sure which engine you have on your 202 Grand Prix, but if you have the most common 3800 V6 this is where it should be. Look at the back of the engine compartment just to the left of the plastic master cylinder resevoir.
Here is a picture you can look at...


c97ac6c.jpg
I hope I was able to assist you!

Posted on Jul 25, 2009

  • 436 Answers

SOURCE: 1996 pontiac grand am se passlock1 or passlock2

passlock 1

Posted on Oct 02, 2009

  • 2926 Answers

SOURCE: remove/replace radiator--1997 pontiac grand am


REMOVAL & INSTALLATION CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
A cross-flow radiator is used on most models. The radiators used on automatic transaxle models are equipped with oil coolers with inlet and outlet fittings for transmission fluid circulation. An aluminum-plastic radiator can be identified by the black plastic side tanks and aluminum radiator.

  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. If necessary for access to the radiator, remove the air intake duct assembly or air cleaner assembly.
  4. On automatic transaxles, disconnect and plug the upper oil cooler line.
  5. Disconnect the engine strut brace at the radiator, loosen the engine side bolt and swing aside, if equipped.
  6. Matchmark and remove the hood latch from the radiator support.
  7. Detach the upper hose and coolant reserve tank hose from the radiator.
  8. Disconnect the forward light harness and fan wiring. Remove the electric cooling fan. On some models this may not be able to be removed unless the front end of the vehicle is raised and supported.
  9. Raise and safely support the vehicle.
  10. Remove the engine cooling fan if not yet done.
  11. If equipped, remove the splash panel below the radiator outlet hose. Detach the lower hose from the radiator.
  12. If equipped, disconnect and plug the lower oil cooler line.
  13. Carefully lower the vehicle.
  14. If equipped with air conditioning, remove the radiator to condenser bolts. Unbolt the refrigerant line clamp. Do not disconnect the lines.
  15. Remove the mounting bolts and clamp, then the shroud (if equipped) and carefully lift the radiator out of the engine compartment.
To install:

  1. Lower the radiator into position.
  2. Install the mounting clamps and bolts, including those associated with air conditioning parts.
  3. Raise and safely support the vehicle.
  4. If equipped, attach the automatic transaxle cooler lines.
  5. Connect the lower hose(s) and attach the splash shield if equipped.

If the engine cooling fan was removed while the vehicle was in the air, install the assembly and attach all electrical wiring.
  1. Carefully lower the vehicle.
  2. If not already done, install the electric cooling fan, then attach the electrical connector(s).
  3. Connect the upper hose and coolant reserve tank hose.
  4. Install the hood latch and strut brace.
  5. Fill the system with coolant.
  6. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their correct levels, then check the automatic transaxle fluid level.
  7. Turn the engine OFF , then once the vehicle has cooled, recheck the coolant level.

Posted on Aug 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission 96 Pontiac grand am se


Unit Model ?

Count the number of bolts on the pan &
make note of the shape

Wikipedia has transmission info

You can ask a dealer & provide your VIN #

Nov 21, 2014 | 1996 Pontiac Grand Am

1 Answer

96 Pontiac grand am se transmission jump when put in drive


you probably have either a busted tranny mount or a motor mount broken

Jan 15, 2013 | 1996 Pontiac Grand Am

1 Answer

96 pontiac grand am se 3.1 is dumping oil over the starter.


If the oil is on the nose of the starter that is inside the bell housing, then it could be the rear main seal. You would have to have the engine or transmission removed to replace the seal.

Oct 04, 2012 | Pontiac Grand Am Cars & Trucks

1 Answer

;where are the plugs and wires on the 96 grand am se


FOR THE 2.3L ENGINE IT HAS THE INTEGRATED DIRECT IGNITION SYSTEM.YOU HAVE IGNITION COILS WITH PLUG BOOTS OVER SPARK PLUGS.YOU HAVE TO REMOVE ENGINE TOP COVER TO REMOVE COILS AND BOOTS FROM SPARK PLUGS.

Dec 02, 2010 | 1996 Pontiac Grand Am

1 Answer

Will a brake caliper (drivers side)of a 1996 pontiac grand am fit a 2001 pontiac grand am?


No that will not fit the the body style changed in 98 see pontiac grand am 96-98 had the same body style and body parts. so i dont think it will work you will nedd to find a caliper off a 99-05 and that should work.

Jan 07, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Cant locate washer fluid motor fuse on 96 pontiac grand prix se


On this website (link below) you find fuse box diagram and description for Pontiac Grand Prix 1996

Pontiac Grand Prix mk5 FifthGeneration 1996 fuse box diagram Auto Genius

Sep 07, 2009 | 1996 Pontiac Grand Prix

1 Answer

Guages


it will be the vehicle speed sensor it is located on the bottom of the transmission on the right side above the driveshaft

Nov 14, 2008 | 1996 Pontiac Grand Am

Not finding what you are looking for?
1996 Pontiac Grand Am Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...