Question about 2001 Lincoln Navigator
I checked the fuse panel under the dash. There are fuses under the hood but I cant tell if they are bad or not.
There is another computer in the cab. IT is called the BCM or ECM by FORD. The computer controls all those things. IT is not to be confused with PCM or EMISSION CONTROL MODULE>
Posted on Nov 21, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Here is how to tell if system is working.Get into the vehicle and close door. Set ignition switch to on position and move the gear shifter to neutral. After a few secs. you should hear the compressor turn on. If it comes on then put shifter back to park leave ignition on and exit vehicle. Compressor will stop when you open the door but should start back up in a couple of secs. after you close the door. You can then walk around the vehicle and listen for leaks.
If compressor does not come on there are 3 fuses and a solid state relay that controls it along with the module.
The 3 fuses are no. 109(50amp) in the battery junction box under hood.This is the direct feed to compressor thru the solid state relay. The other 2 fuses are located in the interior fuse panel and they are no. 6 (5amp) and no. 12(15amp).
What we usually see though if compressor does not run is either a bad compressor or the solid state relay. They both are rather expensive so I would have an experience tech look at it then.
However If you feel confident enough and have a voltmeter or test light respond back and I will tell you which wires to check.
Posted on Mar 12, 2009
check the outputs on the multi function switch (t/s switch) the brake lights and flashers all go threw this switch try to wiggle the flasher button if the lights start to work then the switch is bad to replace switch remove bottom cover by pedals if it has one bottom cover on steering colum has i beleave 4 screws that hold it on, the tilt colum lever unthreads and the cover will come off the upper colum just clips on you will have to remove the key tumbler to get it off . you need to disconnect the battery at this point and block the wheels. to get tumbler out put key in and turn to run postion there is a small silver button that pushes in with small screwdriver once its pushed in use the key to pull tumbler out the top cover will now come off you will probably have to tilt colum down and shift to 1 to get cover off there are 2 torx head screws that hold switch on plug new switch in and reconnect battery to test lights unhook battery again and reassemble please let me know how you make out
Posted on May 22, 2009
Most likely the problem you are experiencing with the park assist is a fault in one of the sensors mounted in the rear bumper. I would not consider it to be a major fix, however there will be a few hours labor involved as the bumper cover needs to be removed to replace the sensors.
Posted on Jul 08, 2009
This is definitely not a job for the at home mechanic. the dash will probably have to come out and this is a very time consuming and laborious task. I would recommend you find a job that you can trust, or get several estimates on the work before you decide who to let do the work. I would expect something like this to run at least $700.00 to $1000.00
Posted on Dec 08, 2009
Tips for a great answer:
Nov 13, 2015 | 2000 Lincoln Navigator
Jul 11, 2009 | 2004 Lincoln Navigator
Dec 03, 2014 | 2001 Lincoln Navigator
Jan 20, 2014 | 2001 Lincoln Navigator
Dec 28, 2012 | 2001 Lincoln Navigator
Mar 23, 2012 | 1998 Lincoln Navigator
Feb 25, 2012 | 2001 Lincoln Navigator
Jul 12, 2011 | 2003 Lincoln Navigator
Jul 11, 2011 | 2005 Lincoln Navigator
Mar 03, 2011 | 2004 Lincoln Navigator
99 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: