Question about Cars & Trucks

Open Question

I need. S free information. On terex d400c transmission

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: I habe a terex d400c dozer it doesnt like to

low on tranny fluid

Posted on Nov 22, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Terex 760b, I've burned up 2 starters in 8 days. Bad wiring? Flywheel? I'm clueless, any advice will be appreciated.


If the starters are making noise when powered up I would check to see they have the correct shims installed. If to tight it can burn they out. How about your solenoid? Is it working properly? Check these things and if this doesn't help post more info as to any noise,etc.Viking.

Mar 29, 2016 | Cars & Trucks

1 Answer

Its hard putting into reverse


Normally when the transmission is hard to get into a gear ,it means the clutch isn't fully releasing making it hard to put the transmission in gear. More information is needed. If this vehicle has a hydraulic master cylinder for the clutch then the reservoir needs to be checked that the fluid is in the full range, If it is then there could be air in the system and the hydraulic system will have to be bled to remove the air. If the vehicle has a cable then the free travel needs to checked. If there is too much free travel then the cable will need to be adjusted to remove the free travel.

Nov 03, 2015 | Cars & Trucks

1 Answer

My terex 2800 will only cable up. not down. any suggestions?


Consult your shop manual for any linkage adjustments then follow them carefully. can you boom down safely to reduce load?

Feb 15, 2015 | Cars & Trucks

1 Answer

I have a terex d400c dozer when u start up it


Ensure the transmission fluid is full. That can cause this issue.

Nov 23, 2014 | Cars & Trucks

1 Answer

Have 12 terex -4 , battery is 12.67 will not start the machine


remove the starter and have it bench tested. Starter motors are subject to dust and the armature shaft bushes get dry and wear out. This allows the armature to pole out and the starter indicates as a bad /flat battery

Nov 18, 2014 | Cars & Trucks

1 Answer

How to remove transmission in 2002 silverado 2500 hd


I can most likely make you up a PDF with pictures and instructions but there were 3 different engines and a couple of different transmissions plus the fact if it was automotic or a manual trans mission as well. Will need that information and If you know the type of transmission including a model that will help as far as being sure you have the correct information. Feel free to email me at csautomotivecars@att.net with that info and I will be happy to help. No there is no fee or cost.....don't mind helping out. Gota tell you though, this isn't the easiest of jobs...

Feb 18, 2012 | 2002 Chevrolet Silverado 2500HD

1 Answer

Wireing diagram for 1999 terex model # TB44


My recommendation is to contact the equipment manufacturer for that. Sorry I can't help you here.

Jan 08, 2012 | Cars & Trucks

1 Answer

Transmission problems


Hello wad.... the best place to go when your transmission is acting up is to an AAMCO repair shop... They offer a free scan of your car's computer and a free estimate you can make an informed decision about having them do the work. Most people do not have the tools or the knowhow to work on the transmission themselves.

The one thing you could do first is to check the transmission fluid. If it is anything less than full add transmission fluid.

Jan 07, 2011 | 2000 Ford Windstar

1 Answer

TEREX 860 temperature gauge not working engine warm gauge in cool area. Cab heater warm not very hot what is the proplem


if the engine is not reaching operating temp, then the heater is never going to blow warm air. I would start with checking temp of engine, if its not warm enough (180f) I would replace the thermostat

Nov 10, 2010 | Toyota Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...