Question about Cars & Trucks

1 Answer

I have a 1991 vandura 2500 5.7 and my transmission will not go into 3rd gear and the 1st&2 gear Work fine help please

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,568 Answers

Might be as simple as a cracked or loose vacuum hose, assuming it is an automatic tranny.

Posted on Nov 20, 2014

  • Dorlando Hayabusa Killerolden

    Yes its a automatic and i i took the pan off no metal flakes in the fluid where is the vacuum house located

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2006 Pontiac G6 GTP Transmission Drive Not Working

trans usually coupled (electroically) with engine revs. check computer chip. perform computer diagnostics.

Posted on Jul 30, 2008

  • 1 Answer

SOURCE: automatic transmission sounds like it stuck in 3rd gear

You need to check the transmission fluid level, if it is low the tranny will not shift. If, however, the fluid is to the proper level then you will need a new transmission.
Try putting new fluid in and look for a leak in the pan gasket, then all you may need is a transmission service. When the service is done the mechanic will look for pieces of metal in the old fluid, if found this is very bad and you will need a new tranny.
You might consider a new or used car, you can definately find a good deal out there!

Posted on Nov 16, 2008

  • 2 Answers

SOURCE: 88 s10 pickup truck will not shift from 3rd gear to overdrive

need more info i had a 1984 chevy half ton and first, second, and third worked fine but lock up didnt work. the problem was there was no vacum at a switch under the hood on the fire wall also your shift linkage could be out of adjustment. try driving down the road and raise up a little on the shifter.

Posted on Jan 25, 2009

mrgreenz
  • 962 Answers

SOURCE: slight miss in engine, hard shift from 1st to 2nd long 2nd gear

Check both O2 sensor(s) and catalytic coverter.. P0420 means catalyst below threshold. Also check the sensor at the transmission and solenoid.

Posted on Feb 06, 2009

lester482529
  • 226 Answers

SOURCE: 1991 Dodge Caravan - Transmission problems

BELIVE ME THIS HAPPENED TO ME AND IT WAS BECAUSE MY OIL WAS LOW CAUSING THE ENGINE TO REV HIGHER TO MAINTAIN SPEED.DO YOUR SELF A FAVOR AND CHECK (ALL) THE FLUIDS IN YOUR VAN 1'ST.HOPE THIS HELPS

Posted on Jul 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Van won't start,rapid clicking heard when key is turned. need help/directions replacing starter relay for gmc vandura 2500, 1991


Check battery connections and battery fuse. Battery may not be large enough for the size of your van

Jan 18, 2013 | GMC Cars & Trucks

1 Answer

I have a 94 chevy 2500 that is stuck in 3rd gear, or wont shift correctly, shop says its an "ignition switch"


My truck had this issue, or one very similar. The 4L80E transmissions have a defect where transmission fluid can leak up into the big round electrical plug and short everything out. There are YouTube videos on how to clean out the plug and seal it so it doesn't happen again.

Mar 09, 2017 | Cars & Trucks

1 Answer

1991 subaru legacy wagon automatic shifts fine into 1st , 2nd, & reverse but slips in 3rd & drive


Sounds like the clutches for 3rd Gear are worn out. Need to rebuild or replace the transmission.

Nov 04, 2011 | 1990 Subaru Legacy

1 Answer

My ford focus tdi 2003 cant select 1st,3rd or 5th gears.


Car is in limp in mode unless you have the tools to work on automatic transmission you will need to take it to a transmission shop. Of course you can check oil level but I suspect you have other issues.

Mar 26, 2010 | 2003 Ford Focus

1 Answer

1991 toyota camry automatic. Transmission is fine


sounds like you may not even have a 4th gear. worst thing is you may need a new transmission. try putting in some "Lucas Transmission Fix" it's like $12 at Autozone.. If that doesn't help, take it to a transmission shop and have them check inside your transmission to see if you need a new transmission or if it's something that could be fixed. It may even be a sensor.

Dec 02, 2009 | 1991 Toyota Camry

1 Answer

Transmission was working fine and just stopped shifting


As long as the fliud is full, I'd say a "hard" part broke. Sun gears come apart, shells in newer ones break. there is an internal problem.

Sep 14, 2009 | 1991 Chevrolet C2500

2 Answers

Transmission problem with a 1999 audi a4 quattr0 2.8l


you may not need a transmission replacement, just try replacing the sensor of the transmission, it may help

Jul 02, 2009 | 1999 Audi A4

1 Answer

Automatic transmission Shift problem


you should first check gear box oil ,level and clean filter.lee

Jan 31, 2009 | 1991 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...