a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
"Replacing fog light bulbs on 2013 Santa Fe". Raise vehicle if you are a big person. In front of front wheels triangular plastic panels exists. Remove Phillips head plastic screws in chosen panel (2ea). Pull panel down. Stick hand through opening, remove wiring connector from bulb. (Bulb will not come out unless you do). Twist bulb housing counterclockwise and remove. Install new bulb, reverse procedure and don't touch the glass part of the bulb.
First you'll have to remoe the door panel and all the little pieces: Remove the little plastic slide piece that locks the door (I'm assuming if you have power windows you have power doors too) Then remove the plastic cover under the door hande. (Pry up with a flathead screwdriver) This will reveal a bolt/screw that needs to be removed. Then pry up the plastic cover that the power door lock switch is on.
Disconnect the wire and set the plastic cover aside. Then remove all the screws along the bottom of the door trim. Remove two srews in a triangular plastic cover, up by the top of the door, by the window and then remove the plastic cover.
Pull out the door panel along the front and back, (it's only connected now by plastic clips/pins.) Pull up on the door panel and it should become loose. You'll have to losen the seat belt to pull the panel away from the door. The panel will remain connected to the door by the seat belt. This is a pain and will keep the door trim in your way the whole time! Carefully pull down the clear plastic vapor barrier.
The window should be halfway down. The lifting arm will be attached to the glass window with two bolts, one on each side. loosen, but do not remove the bolts. (Move the window up and down a little to get it in the best position to reach the bolts.) Be very carful not to break the glass. Disconnect thewindow from lifting arm after you've loosened the bolts, by pulling down on the lifting arm or use the power windowswitch to move the lifting arm down a little.
Tape the window up to the frame so it doesn't fall down while your working. There are two bolts attaching the botom of lifting arm to the door frame, remove them. Disconnect the wire clip from thewindow motor. The Power window motor is attached with 4 rivits. You will have to drill them out and then chop off the rivit heads with a chisel or screwdriver to remove the rivits. The whole assembly can now be removed through the large opening in the door. The window motor is attached to the lifting arm with 3 rivits, they will also have to be drilled out.
***Danger*** the lifting arm is attached to the motor with a large tightly wound spring. This must be secured or locked in place with a hole drilled in the unit and a bolt inserted or it will spring apart and may cause injury!! Also it will be impossible to re-attach the spring correctly if it does come off. Remove the motor and replace it with the new one. The new motor comes with it's own screws so use them to re-attach the new motor to the lifting arm, instead of rivits. Re-install the unit in the reverse order. The motor will have to be mounted to the door frame with 4 new rivits. There is no space to use bolts or screws.
Hope this helps.
The outside mirrors attach to the door frame using 3 nuts that attach to studs that are part of the mirror. You can access the attachments by opening the door and removing the triangular shaped plastic trim piece, removing a piece of foam insulation and then you can see the three nuts to remove.
should have a little triangular plastic trim cover covering it. Just above the door panel on the inside. remove plastic cover, remove attachment bolts, disconnect the mirror electrical connectors and remove & replace, reassemble & test repair
You'll need to remove screws that are by the door handle,
arm rest, under door and side of door and then gently pull back on the
panel as there will also be retaining clips attached and you don't want
to break them. Then you can access the mirror assembly.. it's a huge pain to change such a small part
I have a 2003 Mustang, but assuming it is the same then check the following:
Do you have a speaker (tweater) in the door or just a plastic triangular cover (trim piece) on the inside of the door? If yes, open the door. The trim piece clips in place with plastic lugs. Lifting from the back edge the piece should rotate out either exposing the tweeter or the 3 bolts holding the mirror in place. If the tweeter is there, you will need to remove the speaker first. The bolts for the mirror are attached to plastic, so do not overtighter the nuts when reinstalling or you will have to buy a second mirror. Hope this helps.
If you do not have the triangular piece (i.e. door panel is one piece), the Chilton's manual says the door trim panel must be removed first.
Hiya...the cabin air filter is located below the front passenger/windshield area.
It's only accessible by standing outside the Equinox with the hood open.
Here's how to do it...(before you pop open the hood)
1) Stand outside at the front-right door area.
2) Just below the front windshield area, pull up a few small black plastic clips that's on the black windshield wiper cowl area- a small flat screwdriver or a special clip-remover tool is handy.
3) Raise the hood up.
4) There may be a triangular-shaped hard foam sound damper at the left side nearby the hood hinge...pull it off if it allow you to work around it with ease.
5) Continue to find a few black plastic clips around the black windshield wiper cowl area.
6) Gently pull up the black windshield wiper cowl cover with care not to bend it too hard during removal.
7) You should see the cabin air filter inside that's held in place by a black rectangular box inside.
8) There's 2 black tabs that holds the cabin air filter in place.
9) Insert your finger or tool to pry the cabin air filter away from the tabs.
10) Remove old cabin air filter.
Remember to reinstall the clip parts back into place when you're finished.