Question about Cars & Trucks

1 Answer

Will the 1965 f 100 twin i beam front suspension work under a 1976 f 100 and work right

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,176 Answers

Measure the distance between the spring centre bolts. If it is the same and the tie rod is the same on the steering box pitman arm then it will fit.

Posted on Nov 20, 2014

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Where is jacking point for front tyre change of isuzu npr 200 short truck

under the outer ball joint if independent suspension or under the beam axle under the spring
If you do not know how to jack your vehicle before the problem arises maybe you should not be driving it.
look at the wheel studs ans there will be an L or an R punched on the end of the stud. R is for right hand side ans is undone just like a normal bolt
L will be on the left hand side and is a left hand thread which means that in effect you have to do it up to undo it.

Mar 22, 2015 | Isuzu Cars & Trucks

1 Answer

Want to replace all running gear (axels,tranny,engine) from a 2004 ranger supercab 4x4, into a 1998 supercab (frame and body). Are they compatable?

I am fairly familiar with rangers but I think the cutoff year is 2000 for exchanges. 2000 back to 1989 are pretty much interchangable. The front suspention went to tortion bars in either 98 or 2000 and or springs. the older models had the old twin I beam suspension making the change over nearly imposible. You may be able to put the engine, transmission and the transfercase in with out to much problem but the rest is out.
I hope I have been of help. Good Luck.

Oct 21, 2014 | Ford Ranger Cars & Trucks

1 Answer

Headlight problem on 1994 XJ6 Jaguar

if your car is the xj40 model the lighiting logic module is under the fascia close to the lighting switch but i think the problem is more likely to be a earth problem or simply the bulbs the twin headlamp car has one twin filament bulb on the outer and one single on the inner so if both main beam filaments fail thats what will happen

Jun 15, 2017 | 1994 Jaguar XJ6

1 Answer

Tires bow out

Fords with twin I beam suspension are known for having upper ball joint and lower ball joint issues. Not always worn but in need of adjustment. I see many of these similar vehicles in my shop. Aftermarket companies make a reasonably priced budging that is adjustable. Any reputable alignment shop will be able to install them and adjust the front end back to factory specs.

Jan 20, 2011 | 1986 Ford F 350

1 Answer

Translating japanese to english on fuse box

is located under the dashboard on the driver's side. The fuse label is attached under the steering column. If something electrical in your vehicle stops working, check for a blown fuse first. Below table outlines detail fuse number, its ampere and circuits protected. honda-crv-interior-fuse-diagram-thumb.png
Circuits Protected
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
7.5 15 10 7.5 (15) (20) _ 10 7.5 7.5 10 10 10 7.5 7.5 10 10 20 15 7.5 20 _ _ (20) 20 20 (20) 15 15 20 (15) 20 20 7.5 7.5 10 7.5 30
Power Window Relay Fuel Pump ACG ABS/VSA Heated Seats* Front Fog Lights* Not used Rear Wiper ODS (Occupant Detection System) Meter SRS Right Headlight High Beam Left Headlight High Beam Small Light (Interior) Small Light (Exterior) Right Headlight Low Beam Left Headlight Low Beam Main Headlight High Beam Small Lights MAIN TPMS Headlight Low Beam Not used Not used Moonroof* Door Lock Front Left Power Window HAC Option Rear Accessory Socket Accessory Front Right Power Window Accessory Power Socket on the Center Table* Rear Right Power Window Rear Left power window ACC Radio ACC Key lock HAC Daytime Running Lights Front Wiper

Dec 13, 2010 | 1997 Honda CR-V

2 Answers

Is the 1990 f150 4x4 have a solid front axel or what type of suspension

They usually will have a twin "i" beam with a solid front axel.

Jun 02, 2010 | 1990 Ford F150

1 Answer

My 1989 f-250 has the twin I beam and leafs up front and the suspension sags causing the front tires to kick out like a stadium truck. Is there a kit to fix this???

you can have it aligned and they will use a off set cam at upper ball joint to realign front end if it is not real bad, but the right way to fix it would be to replace the springs and then have it aligned. hope this helps.

Feb 22, 2010 | 1989 Ford F 250

2 Answers

I need catalyst type and DOT numbers on the headlights

2005 avalon high beam..#9005..low beam..#9006st...2008scion..high beam..#9005..low beam..#H11

Nov 13, 2008 | 2005 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides