Question about 2007 Toyota Quantum 2.7

1 Answer

What is the torque settings on n 2007 Toyota quantum vvti 2.7

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Toyota Master
  • 1,869 Answers

-What do you try to tight...?
-Always follow its repair manual.

Good Luck

Mai Lor

Posted on Nov 19, 2014


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 89 Answers

SOURCE: toyota corolla 1.4 vvti cluth problem

try to give it a little gas when letting the clutch out

Posted on Jul 03, 2009

  • 3489 Answers

SOURCE: What torque setting should I use on the wheels of

approx. 95 ft lbs. happy holidays

Posted on Dec 30, 2009

Testimonial: "I hadn't even gotten signed in before I got the answer I was looking for. Great service"

  • 151 Answers

SOURCE: diagram for the timing of a toyota hilux 2.o vvti

get a Haynes manual. @$20 at autozone. money well spend as you will get lots of use from it if you work on your vehicle

Posted on Feb 15, 2010

  • 8197 Answers

SOURCE: what is the procedure to

3.0L Engine

  1. Drain the engine coolant.
  2. Remove the right front fender apron seal.
  3. Remove the v-bank cover.
  4. Disconnect the inlet radiator hose.
  5. Remove the front upper center suspension brace sub-assembly.
  6. Remove the air cleaner assembly with the hose.
  7. Remove the intake air surge tank, as follows:
    1. Disconnect the accelerator cable.
    2. Remove the bolt, and disconnect the speed control cable with the bracket.
    3. Disconnect the Throttle Position (TP) sensor connector.
    4. Disconnect the Idle Air Control (IAC) valve connector.
    5. Remove the 3 bolts, and disconnect the PS pressure tube From the intake air surge tank, throttle body bracket and No.1 engine hanger.
    6. Disconnect the 2 water bypass hoses and No.6 air hose.

FIG : Disconnect the 2 water bypass hoses and No.6 air hose

G. Disconnect the purge hose.

FIG : Disconnect the purge hose

jyackle5_2.jpg H. Disconnect the hoses and cables.

FIG : Disconnect the hoses and cables

jyackle5_3.jpg I. Remove the 2 bolts and No.1 engine hanger. J. Remove the 2 bolts and throttle body bracket. FIG : Location of the No. 1 engine hanger and throttle body bracket

jyackle5_4.jpg K. Disconnect the engine wire from emission control valve set.
L. Using an 8 mm socket hexagon wrench, remove the 2 bolts, 2 nuts and intake air surge tank.
FIG : Intake air surge tank mounting

  1. Remove the ignition coil. For more details, refer to the Engine Electrical Section.
    1. Remove the right and/or left cylinder head cover sub-assemblies, as follows:
    1. Using a E6 Torx® wrench, remove the 2 bolts, and disconnect the engine wire protector, if necessary.
    2. Remove the 9 bolts and cylinder head cover.

    1. Thoroughly clean the gasket mating surfaces.
    FIG : Left side cylinder head cover removal jyackle5_6.jpg

    Posted on Nov 14, 2010

    • 224 Answers

    SOURCE: what is the measure of gear oil for F premio 2007 VVTI ?

    Gear oil level is even with the oil fill port. Just fill it until you can insert your finger slightly into the port and feel oil.

    Posted on Aug 23, 2012

    Add Your Answer

    Uploading: 0%


    Complete. Click "Add" to insert your video. Add



    Related Questions:

    1 Answer

    Torque settings of cylinder head toyota quantum 2.7 vvti petrol

    Cylinder head cover sub-assy x Cylinder head sub-assy 9 92 80 in.?lbf

    Cylinder head sub-assy x Cylinder block sub-assy 1st - 39 398 29

    Feb 12, 2016 | Toyota Cars & Trucks

    1 Answer

    What is the torque settings on n Toyota quantum 2.7

    Too many to give here. Find yourself a manual. If you have a specific one say so. Go online to Toyota Owners forum etc you might be able to download a free one.

    Nov 19, 2014 | 2007 Toyota Quantum 2.7

    1 Answer

    Full engine torque settings for toyota corolla 1.4 vvti 2001 model

    main bearing
    tighting in the following stages:
    22Nm then 44 Nm then 45 degree then 45 degree
    big end bearing
    20 Nm then 90 degree

    Apr 05, 2014 | 2001 Toyota Corolla

    2 Answers

    How to do timing on 2.7 toyota quantum

    how to set the timing marks on the timing sprockets on a vvti quntum

    Apr 30, 2012 | 2007 Toyota Quantum 2.7

    1 Answer

    What is the torque settings for : cylinder head toyota quantum 2.7 vvt. , big ends bearings. , main bearings

    Use a factory service/repair manual. You cannot rely on a possibly wrong answer from this forum.

    Apr 17, 2012 | 2007 Toyota Quantum 2.5

    Not finding what you are looking for?
    2007 Toyota Quantum 2.7 Logo

    Related Topics:

    116 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts


    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides