Question about 2006 Hummer H3

1 Answer

How do I fix ? DTC code u1041 lost communications with chassis multiple control system

Before a friend got the u1041 code for me! I checked all the fuses. All I can find wrong is the heater fan doesn't work

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hummer Master
  • 15,478 Answers

The BCM talks to the ECM and they are not talking. IT could be the cable or one of the computers is bad.

Posted on Nov 19, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im getting codes P0700/ U1041, ALSO C0265, C0298, U1064, CAN SOMEONE HELP ME I HAVE A 2003 CHEVY TRAILBLAZER. I HAVE CHANGED OUT MY TRANSMISSION STRAINER, COIL PACK, SPARK PLUGS, IOL CHANGE. IDK ?ELSE


P0700: Transmission Control System Malfunction
http://www.autocodes.com/p0700.html

U1041: Electronic Brake Control Module Missing Data
http://www.autocodes.com/u1041.html

C0625: ???

C0298: Powertrain Control Module Indicates Traction Control Malfunction
http://www.autocodes.com/c0298_chevrolet.html

U1064: SCP (J1850) Invalid or Missing Data for Primary ID
http://www.autocodes.com/u1064.html

Oct 04, 2016 | 2003 Chevrolet TrailBlazer

2 Answers

How to reset Theft Deterrent fuel enable signal


have you put obd11 scanner on it to find error code.
DTC P1626 Theft Deterrent Fuel Enable Signal Lost
Circuit Description
The Vehicle Theft Deterrent (VTD) system is incorporated within the body control module (BCM). The powertrain control module(PCM) monitors the state of health serial data message from the Theft Deterrent system to ensure that the PCM to BCM communications is established. If the PCM detects a loss of the state of health message while the engine is running, DTC P1626 will set. DTC P1626 can cause a no-start condition or normal operation depending on when the loss of Theft Deterrent system communication was detected. The engine will continue to start and run if the condition that set DTC P1626 occurred after the PCM received a valid theft deterrent password from the BCM and already allowed fuel during the ignition cycle. The engine will start and immediately stall if the condition that set DTC P1626 occurred before the PCM received a valid theft deterrent password. With this condition present, the PCM will inhibit fuel delivery and disable the starter until a valid theft deterrent password is detected. Refer to Content Theft Deterrent (CTD) Circuit Description .

Conditions for Running the DTC
The Theft Deterrent system has allowed fuel delivery.
Conditions for Setting the DTC
The PCM has detected a loss of the state of health serial data message from the Theft Deterrent system.

Action Taken When the DTC Sets
The PCM stores conditions which were present when the DTC set as Failure Records only. This information will not be stored as Freeze Frame Records.

Conditions for Clearing the MIL/DTC
The DTC becomes history when the conditions for setting the DTC are no longer present.
The history DTC clears after 40 malfunction free warm-up cycles.
The PCM receives a clear code command from the scan tool.
Diagnostic Aids,
An intermittent may be caused by:

• A poor connection

• Rubbed through wire insulation

• A wire broken inside the insulation

Check for the following conditions:, • Intermittent short circuit on the serial data circuit -- Refer to Data Link Communications Operation in Data Link Communications. Be sure to check all related wiring for an intermittent short to ground or short to voltage.

• Poor connection -- Inspect the wiring harness for damage. Check for an intermittent short or open circuit in the wiring harness related to the BCM, including the ignition, battery feed, ground, and Serial Data circuits.

Mar 13, 2016 | 2001 Buick Park Avenue

1 Answer

What are the probable causes of DTC U1000?


DTC U1000 and U1255
Class 2 Communication Malfunction , Do you know what class 2 serial data communication network is ? What module set this code an what kind of scan tool did you use to read this code .
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the ID number of the module which sent the message for State of Health monitoring, Node Alive messages. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. When a module does not associate an ID number with at least one critical parameter within about 5.5 seconds of beginning serial data communication, DTC U1000 or U1255 is set. When more than one critical parameter does not have an ID number associated with it, the DTC will only be reported once.
The table below list the modules on the Class 2 Serial Data Circuit that will set a U1000 or U1255 and should be actively communicating the previously described messages on the Class 2 Serial Data Circuit.

Control Module

ID Number
Body Control Module (BCM)
064
Electronic Brake Control Module (EBCM)
040
Instrument Panel Cluster (IPC)
096
Radio
128
Powertrain Control Module (PCM)
016
Sensing and Diagnostic Module (SDM)
088
Diagnostic Aids
When a malfunction such as a open fuse to a module occurs while modules are communicating, a Loss of Communication DTC is set as current. When the modules stop communicating, ignition is turned off, the current Loss Communication DTC is cleared but the history DTC remains. When the modules begin to communicate again, the ignition is turned on, the module with the open fuse will not be learned by the other modules so U1000 or U1255 is set current by the other modules. If the malfunction occurs when the modules are not communicating, only U1000 or U1255 is set.
Test Description
The numbers below refer to the step numbers on the diagnostic table.

  1. A DTC U1001 - U1254 Lost Communications with with a history status may indicate the cause of U1000 or U1255.

  2. The modules not communicating are the likely cause of U1000 or U1255. The modules that are available on the class 2 serial data circuit are listed in the Circuit Description.

  3. The module which was not communicating due to a poor connection to the class 2 serial data circuit may have set DTC U1001 - U1254 Lost Communications with for those modules that it was monitoring.

  4. The modules which can communicate indicate the module which cannot communicate. You must clear the serial data communication DTCs from these modules to avoid future misdiagnosis.

  5. If all modules are communicating, the module which set U1000 or U1255 may have done so due to some other condition.

  6. The module which set U1000 or U1255 is the likely cause of the malfunction.

1
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Record the DTCs set in each module. If using a Tech 2, use the Class 2 DTC Check feature to determine which modules have DTCs set.
Did you record any DTCs in the range of U1001-U1254 with a history status?
Go to Diagnostic Trouble Code (DTC) List
Go to Step 2

2
  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to communicate with each module on the class 2 serial data circuit. If using a Tech 2, obtain this information using the class 2 Message Monitor feature.
  3. Record all of the modules communicating on the class 2 serial data circuit.
  4. Compare the list of modules which are communicating to the list given in Circuit Description.
Does any module on the class 2 serial data circuit not communicate?
YES - Go to Step 3
NO - Go to Step 12
Test the following circuits of the module that is not communicating for an open or short to ground:
?€¢
The battery positive voltage supply circuits


?€¢
The switched battery positive supply circuits


?€¢
The battery positive voltage output circuits


?€¢
The ignition voltage input circuits


?€¢
The ignition voltage output circuits

Refer to the following:
?€¢
Control Module References in Body Control System for the applicable schematic


?€¢
Circuit Testing in Wiring Systems


?€¢
Wiring Repairs in Wiring Systems

Did you find and correct the condition?

5

Important: Inspect all connectors in the serial data communications circuit.
Refer to the following:
?€¢
Data Link Connector Schematics


?€¢
Testing for Intermittent Conditions and Poor Connections in Wiring Systems


?€¢
Connector Repairs in Wiring Systems

  1. Turn OFF the ignition.
  2. Test the class 2 serial data circuits of the module that is not communicating for an open. Refer to the following:
?€¢
Data Link Connector Schematics


?€¢
Circuit Testing in Wiring Systems


?€¢
Wiring Repairs in Wiring Systems

Did you find and correct the condition?
Go to Step 8
Go to Step 6

6
Inspect the harness connector of the module that is not communicating for poor connections and terminal tension at the following circuits:
?€¢
The battery positive voltage input circuits


?€¢
The switched battery positive voltage supply


?€¢
The battery positive voltage output circuits


?€¢
The ignition voltage input circuits


?€¢
The ignition voltage output circuits


?€¢
The ground circuits


?€¢
The class 2 serial data circuits

Refer to the following:
?€¢
Control Module References in Body Control System for the applicable schematic


?€¢
Testing for Intermittent Conditions and Poor Connections in Wiring Systems


?€¢
Connector Repairs in Wiring Systems

Did you find and correct the condition?
Go to Step 8
Go to Step 7

7

Important: Perform the module programming or setup procedure if required.
Replace the module that is not communicating. Refer to Control Module References in Body Control System for the appropriate Repair Instructions for the module replacement.
Did you complete the replacement?
Go to Step 10
--

8

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Select the Display DTCs function for the module which was not communicating.
Does the scan tool display any DTCs which do not begin with a "U"?
Go to Control Module References in Body Control System for applicable Diagnostic System Check
Go to Step 9

9
Use the scan tool in order to clear the DTCs.
Did you complete the action?
Go to Step 10
--

10

Select the Display DTCs function for the modules which had U1000 or U1255 set as a current DTC.
Does the scan tool display DTCs which do not begin with a "U"?
Go to Control Module References in Body Control System for applicable Diagnostic System Check
Go to Step 11

11

Use the scan tool in order to clear the DTCs.
Did you complete the action?
System OK
--

12
Did you record any other DTCs for the modules which had U1000 or U1255 set as a current DTC?
Go to
Control Module References in Body Control System for applicable Diagnostic System Check
Go to Step 13

13

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool in order to clear the DTCs.
  4. Turn OFF the ignition for at least 5 seconds.
  5. Turn ON the ignition with the engine OFF.
  6. Select the Display DTCs function.
Does the scan tool display U1000 or U1255 set as a current DTC?
Go to Step 14
Go to Diagnostic Aids

14
Important: Perform the module programming or setup procedure if required.
Replace the module which had U1000 or U1255 set as a current DTC. Refer to
Control Module References in Body Control System for the appropriate Repair Instructions for the module replacement.
Did you complete the replacement?
System OK

Mar 12, 2016 | 2002 Pontiac Grand Am GT1

1 Answer

I have multiple codes instrument cluster codes: u1073, u1262, u1059, u1123, u1041; ABS/TCS codes: u1073, u1262, C1805, B2900;


Did you change any modules on the vehicle ?
B2900 VIN Mismatched ABS Module VERIFY that the module has the correct as-built data.
CHECK for correct powertrain control module (PCM) and ABS module configuration using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 303-01A or Section 303-01B for the PCM. CLEAR the DTC. REPEAT the C1805 Mismatched PCM and/or ABS/TC Module ABS Module CHECK for correct PCM and ABS module configuration using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 303-01A or Section 303-01B for the PCM. CLEAR the DTC. REPEAT the self-test. U1073 SCP (J1850) Invalid or Missing Data for Engine Coolant PCM REFER to Powertrain Control/Emissions Diagnosis (PC/ED) manual. U1262 SCP (J1850) Communication Bus Fault Network Fault REFER to Section 418-00 . Can a scan tool communicate with all the modules on the vehicle ?
  • The anti-lock brake system (ABS) module or stability assist module (if equipped) does not respond to the diagnostic tool
  • Circuit or connection in the standard corporate protocol (SCP) network.
  • ABS module.
  • Go To Pinpoint Test A .
U1123 Invalid or Missing Data For Odometer Instrument Cluster Go To Pinpoint Test G . U1059 SCP (J1850) Invalid or Missing Data for Transmission/Transaxle/PRNDL PCM REFER to Powertrain Control/Emissions Diagnosis (PC/ED) manual. U1041 SCP (J1850) Invalid Or Missing Data For Vehicle Speed Instrument Cluster REFER to Section 413-01 . U1041 SCP (J1850) Invalid Or Missing Data For Vehicle Speed Tire Pressure Monitoring System Module REFER to Section 204-04 . You need to take it to the dealer , not a transmission shop. Your vehicle could have a ground issue , could have power issue , could have a control module issue . It needs to be hooked up to the factory scan tool ! It is for sure it has a communication problem on the SCP data bus , do you know what serial data communication is ?
The vehicle has 3 module communication networks:
  • the standard corporate protocol (SCP) communications network
  • the international standards organization (ISO) 9141 communications network
  • the universal asynchronous receiver-transmitter (UART) based protocol (UBP) communications network
The diagnostic tool connects to all 3 networks through the data link connector (DLC). This makes diagnosis and testing of these systems easier by allowing one diagnostic tester to be able to diagnose and control any module on the 3 networks from one connector. The DLC can be found under the instrument panel between the steering column and the radio.
The SCP communications network will remain operational even with the severing of one of the bus wires. Communications will also continue if one of the bus wires is shorted to ground or voltage, or if some but not all termination resistors are lost. The SCP communications network allows inter-module communication.
The ISO 9141 communications network does not permit intermodule communication. When the diagnostic tool communicates to modules on the ISO 9141 communication network, the diagnostic tool must request all information, or initiate module commands.
The ISO 9141 communications network will not function if the wire is shorted to ground or battery voltage. Also, if one of the modules on the ISO 9141 communications network loses power or shorts internally, communications to that module will fail.
The UBP communications network will not function if the wire is shorted to ground or voltage. The UBP is different from the ISO communication network in that it allows intermodule communication.

Sep 13, 2015 | 2004 Lincoln Aviator

1 Answer

What is the code u0184 mean in a 2009 pontiac g8 6 cylinder


U0184 00
Lost Communication with Radio , did you replace factory radio ?
The communication among control modules is performed through the High speed GMLAN serial data circuits and the Low speed GMLAN serial data circuit. The modules that need real time communication are attached to the High Speed GMLAN network. The body control module (BCM) is the gateway between the high and low speed networks. Refer to Body Control System Description and Operation for more information about the gateway.
Signal supervision is the process of determining whether an expected signal is being received or not. Some messages are sent on a periodic basis and are interpreted as a heartbeat of a device. If such a signal is lost, the signal supervision part of the software will set a no communication DTC (U code) against the missing device. This code is mapped on the scan tool screen as a code against the physical device. A lost communication DTC typically is set in modules other than the module with a communication failure.
Does the vehicle start an run ?

Jun 01, 2015 | 2009 Pontiac G8

1 Answer

2000 buick lesabre leveling compressor won't turn on I took off n hooked to battery and works that way I checked all relays and fuses and there good


This is the way you start diagnosing this system !
Automatic Level Control Diagnostic System Check
Install a scan tool. Does the scan tool power up?
Go to Step 2
Go to Scan Tool Does Not Power Up in Data Link Communications

2
  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to establish communication with the Rear Integrated Module (RIM).
Does the scan tool communicate with the RIM?
Go to Step 3
Go to Scan Tool Does Not Communicate with Class 2 Device in Data Link Communications
Select the automatic level control display DTC function on the scan tool.
Does the scan tool display any DTCs?
Go to Step 4
Go to Symptoms

4
Does the scan tool display any DTCs which begin with a "U"?
Go to Scan Tool Does Not Communicate with Class 2 Device in Data Link Connector Diagnosis
Go to Step 5

5

Does the scan tool display DTC B1007 or B1009?
Go to Diagnostic Trouble Code (DTC) List/Type in Body Control System
Go to Step 6

6

Does the scan tool display DTC B1327?
Go to Diagnostic Trouble Code (DTC) List/Type in Engine Electrical
Go to Diagnostic Trouble Code (DTC) List/Type
This is one you should take to a ASE certified repair facility , there are electronic modules involved you have no idea about !

May 16, 2015 | 2000 Buick LeSabre

1 Answer

2003chevy express 3500 W/6.0 cable throttle. Trouble codes U1000,U1016,U1041. Instrument cluster drops off,(gauges go dead) EBS light stays on,security lights also. Van had a remote starter alarm system...


U codes pertain to the class 2 serial data network . A dead module ,a short on the network will bring down the network - no communications between modules = no start problems .
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the identification number of the module which sent the message for State of Health monitoring. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. When a module does not associate an identification number with at least one critical parameter within 5 seconds of beginning serial data communication, DTC U1000 or U1255 DTC is set. When more than one critical parameter does not have an identification number associated with it, the DTC will only be reported once. The class 2 serial data line on this vehicle is a star configuration. The following modules communicate on the class 2 serial data line:
• The body control module (BCM)
• The electronic brake control module (EBCM)
• The inflatable restraint sensing and diagnostic module (SDM)
• The instrument panel cluster (IPC)
• The powertrain control module (PCM)
• The radio
• The remote control door lock receiver (RCDLR)
• The vehicle communication interface module (VCIM)

Look's like a communication problem with the PCM & EBCM !
Powertrain Control Module (PCM)
U1016
Electronic Brake Control Module (EBCM)
U1041
Diagnostic Aids
• An intermittent open between a module and a star connector may cause this DTC to set.
• A poor connection at a module or a star connector may cause this DTC to set.
• An intermittent open in a star connector may cause this DTC to set.
• An open voltage or ground circuit to a module may cause this DTC to set.
• An internal module malfunction may cause this DTC to set.


012 GM Class II Communications

May 12, 2017 | Chevrolet Cars & Trucks

1 Answer

Obd code U1041


Codes U1XXX (where XXX stands for several possible numerical digits, 001 - 254) are communications fault codes. The first part (U1) tells you that there is a communication problem with one of your many onboard control modules. The second part (XXX) or in your case, (041) tells you which module is not communicating. It can vary from year to year, model to model. so without knowing the year and model of the vehicle we are talking about, I cannot tell you which one.

In any case, there is a module that is not communicating with the other modules that are sharing information through the Class 2 serial data circuit. One module uses U-codes to tell on the other modules. For instance, If you got the U1041 code out of scanning the Engine Control Module, you can bet that the Engine Control Module is not having a problem communicating. If it was, you would get a non-communication fault from your scan equipment and the ECM would not tell you anything. Instead, the ECM is telling on the module that is not communicating properly .

I like to call these codes the 1-800 codes...THE PHONE LINE IS DOWN... lol ;)

Nov 24, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Trouble codes P0128, P0455 and U1041


P0128 is the coolant is below normal temperature.
P0455 is Evap system detects a large leak.
U1041 is communication was lost to brake control module.
It is weird that you are having these problems at the same time.
You may not have a problem in anyone of these systems. But again you may.I would suggest that you look into the battery, related wiring, connections, and the alternator. If the electronics are not getting enough voltage then you can have system failure.

May 14, 2010 | 2004 Chevrolet Blazer

Not finding what you are looking for?
2006 Hummer H3 Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7727 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...