Question about Cars & Trucks

1 Answer

<!-- from fixya rte -->Whyis 5.9 Cummings has no oil pressure - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 22,127 Answers

Check oil level. Check oil pressure sender. Check oil pump. Check main and big end bearings.

Posted on Nov 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pressure on my 1991 Nissan sometimes drops to about 5 psi at idle when at operating temp. Other times it will drop to a more normal 25-30 psi. Is there is a high pressure relief valve sticking?


5 psi then 25 -30
what are these readings from ..an after market oil pressure gauge ?
oil light should come on if 5

what make of nissan
how many miles/kms on the clock

would first replace oil pressure sender
oil pressure relieve valve on the oil pump sticking is a possible
oil lower W rating used too thin at the moment
clogged oil filter or sump pick up
oil pump worn or
main bearings worn

d9bd060f-1356-4fbd-9c83-7a0956b9993b.jpg

Jan 20, 2017 | Nissan Cars & Trucks

1 Answer

What is the acceptable max oil clearances on bigends and main bearings on a Cummins 6BT5,9 engine pls. Donr advise AGAIN Buy a Heinz Manual please.


Hi again i found this info on rod & crank clearance 5.9 Cummings .002 to .004 U can always check clearance with plastiguage just to make sure hope this helps GOOD LUCK. only thing i could find was bigend side clearance min .004 max .013in crankshaft end clearance min .004 max.017. ,TRY RINGING CUMMINGS 03 9765 3222 or 03 9360 0800. Good luck....Cummings 6B, 6BT, 6BTA Main Bearing bolts 176 Nm, 130 lb.ft. Con rod 102 Nm, 74 lb.ft. Cylinder head bolts 126 Nm 93 lb.ft ...... Cheers

Nov 19, 2016 | Cars & Trucks

1 Answer

P1747


P1747- Electronic Pressure Control Solenoid - Short circuit.

Jul 26, 2014 | 2000 Ford F150 Flareside SuperCab

3 Answers

Oil light on after engine warm-up on idle


this means a mechanical gauge test is required to check actual pressure warm idling if low below 20 psi then the oil pressure pump relief is stuck open or engine bearing are worn

May 15, 2014 | 2005 Opel Astra 1.4

1 Answer

I have a 1999 dodge ram 2500 Cummings i put it in gear it will go about 5 feet and it stops moving like its in neutral any ideas?


sound like transmission slipping not enough oil pressure to shift in drive.best have vechicle code scan and pressure test.could need fluid and filter change.or you have faulty shift solenoid or governor pressure sensor faulty.

Jul 28, 2013 | Cars & Trucks

1 Answer

Oil gauge flickers back and fourth wnen crusing 1995 dodge ram 2500 with cummings diesel 6 cly


possibly the oil sending unit, it may be bad or the wire may have a short in it

Oct 07, 2009 | 1995 Dodge Ram 2500

1 Answer

Turbo just stopped working,no pressure on guage,no warning,2005 f-250 superduty,2wd,cummings turbo deisel,85,000 miles


A Cummings? Are you sure it is not a Powerstroke? If it is a powerstroke the check the little hose on the passenger side of the intake to make sure it is connected to the nipple on the manifold. Also check on the connector on the turbo that has two wires going to the vgt solinoid. Make sure it is plugged in.

Aug 12, 2009 | 2005 Ford F 250 Super Duty

1 Answer

I have a 2001 dodge ram 3500 cummings. When I the


The accumulator may not be holding pressure or else the cruise control switch may having a fault effecting the cruise control circuit.
Check all the vacuum lines on the accumulator and the reset of the system.

Jul 16, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

FUEL IN OIL PAN


There is a good chance that one of the injectors are leaking and needs to be replaced. It's common on the cummings for the injectors to leak if there is a lot of idle time. Good luck and keep me posted. 

Jun 27, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

Rail pressure


You will need a fluid filled gauge capable of reading 250 psi it can be installed in the rail plug on the shutdown solenoid.
In order to get an accurate reading it may have to be on a dyno.
good luck

Jul 09, 2008 | 1997 Dodge Ram 2500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...