Question about Cars & Trucks

1 Answer

Connections aren't connected!!!! - Cars & Trucks

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Connect them. That will getter done

Posted on Nov 18, 2014

  • John Ahfua Nov 18, 2014

    I would have if they went together but they don't.

  • John Ahfua Nov 18, 2014

    I posted a picture but it's not showing



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

89 Cavalier Z24-2.8L-MPI-No Start-Will run if fed fuel thru throttle opening-fuel under pressure in rail- what am I missing?

I don't have my automotive software at my leisure right now but, look for a fuel pump relay; google it if you have to. Make sure the connections aren't corroded 'anywhere' in the fuel delivery system. And make sure they replaced the screen for the fuel pump when they replaced it..

Sep 06, 2012 | 1989 Chevrolet Cavalier

1 Answer

How do I remove left turn signal switch on 2002 silverado

if your bulbs are fine check connections at base of steering column it would be unusual for the switch to be bad this is a multifubction switch it controls not only turns but wipers bright dim controls washers ect if it is bad you'll need to disarm the air bag remove steering wheel remove access panel under steering wheel remove possibly remove pressure plate under the steering wheel if torq bolts aren't visible there will be three unbolt harness at block connector it bolts together remove two flat connectors for block connector rought wires through column then repeat process on reassembly

Jul 04, 2012 | 2002 Chevrolet Silverado 1500

1 Answer

Running light fuse keeps blowing what could be the problem

Check the wiring connections that lead the running light to the fuse box and also the wiring connecting to the power source. It is easier to find the wiring routes by using a multimeter. The fuse is popping because of the a surge of electricity that is rated higher than the fuse allows, this is to protect your vehicle from overloading circuits. If you aren't worried about taking a small risk you could put a slightly larger fuse in it (if its supposed to be a 10 use a 15). I don't suggest it but it would be a quick fix.

Mar 29, 2012 | 1990 Toyota 4Runner

1 Answer

Hight beam wont come on

If you check to make sure your headlight switch connector is plugged in correctly and all other connections are made then the head light switch ( high beam portion) internal connections aren't making a good enough contact or are broken. In this case replace switch.

Feb 27, 2012 | 1986 Hyundai Excel

1 Answer

Horn not working

Check appropriate fuse isn't broken and from fuse work back along wire checking connections and insulation until you reach the horn. If you've not found a fault download user manual (for free). Ask advice at a Honda dealers or e-mail Honda directly.
Auto-electricians aren't cheap.
I'm not certain but I think youv'e gotta have working horn to pass MOT.
Good luck. Hope this helped.

Dec 14, 2011 | 2000 Suzuki Vitara

1 Answer

It wont hold its volts and it powers down when i drive it or let it sit running after 5 min new bat , alt , starter

your battery needs replacement, it may show 12 volts but the amps aren't being charged enough,, if you take the battery and have it load tested,, you will see that one or more of the cells isn't charging correctly,, if the battery checks out ok, then with the truck running, place test leads on the pos and neg battery terminals,, you should be seeing a reading of 13.5-14.5 volts,, if not your alternator is bad, if you do,, its the battery for sure , make sure also that all the battery connections are clean and tight ,, dirty or loose connections will prevent good charging

Aug 13, 2011 | 1996 Dodge Ram 2500 Club Cab

1 Answer

2 lines from the fuel pump not hook up an car want start

not sure what your asking for but if the fuel lines aren`t connected then any car won`t start and run.connect the lines to fix it,the fix is not that hard going by what you have written.

Jun 22, 2011 | 1999 Pontiac Sunfire

1 Answer

Code p1633. car spudders,hesitates,chuggs. runs better sometimes that others.keyless entry,power drivers seat, not working. low voltage seems possible. what should i do?

P1633 --Keep Alive Power Voltage Too Low

You provided no vehicle info

I would suspect battery connections or a near
dead battery

You could check the fuse but will have to use your
owners manual,we don't have any data for anything,
we are at home like you

Then the most likely cause is a poor wire connector

I suspect from your name,your not onto car electronics,
so a repair shop will be your only bet

They aren't too fond of fords or lincolns ,so your running
the show & telling them what to test & repair. Your looking
at diagnostic time, no parts or actual repairs

Jun 15, 2011 | Lincoln LS Cars & Trucks

1 Answer

99 taurus, automatic. Reved up to 6, 7 rpm with no power. Not over 35 MPH. Wont shift, its an automatic. O/D off light started flashing. Speedometer still working.

Sounds like your transmission might be slipping...or your plugs aren't hitting. O/D off light flashing?
When was the last time you cleaned your plugs; had a tune up? Check some of your fuses, for the O/D flashing problem... and try to check all your hoses and connections.

Apr 22, 2011 | 1999 Ford Taurus

1 Answer

I have a 91 mazda 626. directionals and4 ways dont work properly

check all of your wires with wire tester. maybe they are being shorted out somewhere. Check your fuses to make sure none are blown/bad. Check the light bulbs to make sure they aren;t blown.

Mar 11, 2010 | 1995 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides