Question about Cars & Trucks

1 Answer

How do i remove hyundai accent 1.3 1999 model ignition barrel

Steering wheel is also locked

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

Do you have the ign key ? if not then it is going to be a lot harder . remove the upper and lower steering cowling , you will then have access to the ign switch , if you have the key insert and turn, if stiff spray some lubricating oil ie WD 40 down barrel to ease turning, until the steering lock comes off, at the back of the steering switch there will be a pop up metal nub , depress this and the barrell should slide out , if you do not have the key you may have to change the whole switch unit , keep me posted if you wish

Posted on Nov 18, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

280zlvr
  • 126 Answers

SOURCE: 1994 jeep cherokee steering column housing removal

there is a small round spring clip on the 3/4'' steel shaft almost hiden by metal plate push down on plate with plate pushed down have a trusted friend carefully remove steel spring clip with a small scriber or similar careful not to poke friend with tool good luck with this project

Posted on Jun 30, 2008

  • 2920 Answers

SOURCE: hyundai accent 1996 steering lock removal

try tunring the key and the whell at the same time it should release the lock.

Posted on Aug 22, 2008

freetek
  • 5568 Answers

SOURCE: A4 steering lock does not engage and car won't turn over

The steering locks don't necessarily engage when the key is removed, I always turn the wheel before exiting to engage it. There are several positions that will allow the pin to lock in but if between these, it may seem that it isn't locked.

Posted on Aug 23, 2008

  • 4 Answers

SOURCE: mercedez 190 ignition barrel. I have taken out ignition barrel attached to steering coloum but i can not remove key ignition from steering coloum how does it remove ignition barrel from steering

Should be the same as w123 model. Check diy Mercedes web page.
Photos included easy to do.

Posted on Jul 07, 2009

  • 69 Answers

SOURCE: ignition key won t turn. steering wheel locked

the key may be worn badly or the ignition needs to be replaced.

Posted on Jul 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove the ignition lock cylinder on a 2005 Hyundai accent if u can't turn to acc? It won't turn at all, I've jiggled the key, and turned the steering wheel, which is also locked..


There should be security bolts holding the lock cylinder to the column. Security bolts heads twist off at the factory leaving a smooth top that you have to back out with a sharp center punch and hammer.

Jun 12, 2015 | 2005 Hyundai Accent

2 Answers

How do I get my car keys out when it is stuck in my Nissan Micra K12 ignition?


Try to turn the steering wheel gently from side to side while pulling on the key. Quite often the steering lock engages with the steering wheel shaft and it makes it difficult to get the key out while the shaft puts pressure on the lock.

Feb 13, 2015 | Nissan Cars & Trucks

1 Answer

I have a 1995 hyundai accent the key is broke in the ignition lock. ho can i remove the lock.


Sorry to say but you have to remove the center housing of the steering wheel and use a wheel puller to remove the steering wheel itself. You may find a tempered steel C-Ring holding a tephalon spacer. If you go that far with it I am sure it will come in to place.Hope this helps.

Feb 11, 2011 | 1996 Hyundai Accent

1 Answer

How do i unlock my manual Hyundai accent 2000 steering wheel ignition lock


Unless the vehicle has just a tremendous amount of sloppiness in the steering wheel or the ignition switch. It may just be in a bind and need a little more pressure than normal to allow you to unlock it. It may even take the help of a friend if it's in a bind or the steering is locked with the wheels turned severely one direction or the other. Have a friend grab the steering wheel and pull it down hard to the left or right while you try to turn the key. I mean a hard steady pull, not a quick ****. If it still doesn't release you most likely have an internal problem with the locking mechanism or the ignition switch itself.

Jan 04, 2011 | 2000 Hyundai Accent

2 Answers

How do you adjust the steering wheel in a 2005 Hyundai accent


turn the steering wheel lock to lock and count. put in the middle. if the tyre is not straight... need to do wheel alignment.

Nov 20, 2010 | Hyundai Accent Cars & Trucks

1 Answer

HOW DO YOU REMOVE IGNITION KEY CYLINDER FROM 2006?


ignition key cylinder is normally attached to ur steering wheel shaft/ u can remove it by loosening the screws and bolts and nuts that fasten it to the base.....

Apr 09, 2010 | 2006 Hyundai Accent

1 Answer

How do to remove ignition barrel as key broken in barrel


You must remove the steering wheel and locking plate underneath. This requires special tools that may be lended to you if you live near an Autozone and purchase the parts from them. To remove the tumble you must turn it to the "run" position with a screwdriver and poke in the small locking pin that is located on the front bottom surface of the tumbler bore. If you are unable to turn the keyswitch, it becomes necessary to replace the entire steering collar. Thank you, Dana

Feb 15, 2010 | Hyundai Accent Cars & Trucks

1 Answer

Can't turn ignition key and steering wheel in


Play around with the steering wheel. Also jiggle the ignition key switch while doing this. It should eventually free up yiour igniton.

Feb 03, 2010 | 2000 Hyundai Accent

1 Answer

Hyundai accent 1996 steering lock removal


try tunring the key and the whell at the same time it should release the lock.

Aug 05, 2008 | 1996 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...