Question about 2006 Ford Freestyle SE

1 Answer

Hi good morning i toke my radio out to clean when i put back it dosn´t work.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    Visited the website for 3 consecutive days.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 155 Answers

Did you reconnect all the plug's?
Check also fuse.

Posted on Nov 18, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Chevrolet S10 radio wiring

are you trying to put radio in this s-10 reply back and i could be some help to u..

Apr 13, 2013 | 1998 Chevrolet S-10 Pickup

1 Answer

Wire touched and now windows or radio dosn't work

Check you fuses at both the inside fuse box and the underhood fuse and relay box near the battery, use a 12 volt test light with the key turned to run.

Sep 28, 2012 | 1992 Lincoln Town Car

1 Answer

Window washer isn't working - what could be the problem.?

it could be the washer motor, it is realy easy to test it you just have to unplug the harnes of the washer motor and take a pice of wire long enough to get to te battery and put the wires from the battery to the motor if it does work then you may have a bad washer fuse or switch, if it dosn´t do nothing then is the motor, you can get ir out of a junk yard for arround 5 dollars, hope this hepls.

Dec 21, 2010 | 1999 Kia Sephia

1 Answer

Hi my name is Olafur and this morning I put my car in 4wd and now I cant put it back in 2 wd B reg Oli

Find an empty parking lot and back the vehicle up while turning the steering wheel all the way right & all the way left .
I assume the unit is equiped with autolock front hubs and they get sticky & won't disengage. Good Luck

Mar 02, 2010 | 2005 Lincoln Navigator

3 Answers

Volume in 2003 yukon denali quit working on radio,

check your manuals guide book on reprogramming the radio and where would you find the fuse for the radio first check the fuse then reprogram if this information has been helpful please let us know good kuck

Jul 28, 2009 | 2006 GMC Sierra Denali

1 Answer

BMW 318 would not start this morning Error code 2BOA?

I think you need a new battery.
Replace it and the radio will probably reset ok when you input the code..

Jul 09, 2009 | 1996 BMW 318

2 Answers

Engine wont turn over

I dig the VW... good choice of car. Since you changed the battery, you may consider checking the terminals again. You may not have tightened them sufficiently. Lights and radios use a very small amount of power, but the starter uses several hundred amps. Any poor connection will result in a dramatic reduction in voltage and amps for the starter. Check those connections and tighten them down. If you have a terminal cleaner, clean both terminals again. They have a wire brush on two ends and cost about $5 at the local auto parts store. On Volkswagen, the starter solenoid is located inside the starter and is not servicable. If this is failing you will need a new starter (about $250 installed). Also, VW have a starter relay on the relay panel. I have never personally seen one of these fail on a latemodel VW, but I wouldn't rule it out. Some aftermarket batteries have smaller posts than the OEM posts... this could also be the cause for the bad connection. The bolt may be tightened all the way, but it's still not gripping enough. If that's the cause, back the bolt out all the way. GENTLY, hammer the terminals onto the battery as far as they will go, then replace the bolt and tighten with tools. Anyway, your symptoms point to bad connection on the terminals and your recent battery replacement kind of confirms this. Good luck.

Jul 06, 2009 | 1999 Volkswagen Passat

1 Answer

I have a prelude 91,aut.trans,all speed work but only in reverse dosn´t work.

reasons for no reverse 4th gears or worn and damage-reverse gears worn-4th clutch is faulty-control cable misadjusted-servo shaft stuck-1-2 shift valve faulty-electrical system is faulty.

Jun 13, 2009 | 1991 Honda Prelude

2 Answers

Key is on....battery is good....engine won't turn over

Black box (plastic) usually pretty handy to battery, you should see red (usually) cable from battery running to it. Another thing that came to mind, you don't have anti-theft system on that do you? Sometimes they will cause problems after a dead battery. Try using your key & valet key to unlock the doors, manually especially drivers.

May 18, 2009 | 1993 GMC Suburban

Not finding what you are looking for?
2006 Ford Freestyle SE Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides