Question about Cars & Trucks

1 Answer

If torx converter is bad on 02 545rfe. Will it make the tranny not be able to move in any gears or could it be the pump, tranny rebuilt 8 months ago

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 56 Answers

Yep both

Posted on Nov 18, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1984 gmc sierra shifting hard in all gears

Your throttle valve on the transmisson is probley not adjusted to spec on this vehicle it runs from carb to right side of trans.


hope this helps

Posted on Feb 12, 2009

  • 186 Answers

SOURCE: LOUD WHIRRING NOISE FROM CHEVY BLAZER TRANNY

It sounds more like the pump, if the converter fails it would have a crazy lock up shifting problem. Sometimes the bearing for the torque converter will loosen and spin in the housing this to could be the issue.

Posted on Aug 04, 2009

garyatwell
  • 72 Answers

SOURCE: How to tell if a torque converter in TH400 is

First, are you sure the leak is actually tranny fluid and not oil from a leaky rear main seal in the motor? I have had that problem. A used converter should not be a problem

Posted on Nov 08, 2009

autotherapis
  • 501 Answers

SOURCE: Won't shift from 2nd gear to drive unless i run

This trans has a safety built in to default to second gear if the computer sees any kind of problem. Have it scanned. It can be an input or out put speed sensor, or even a temp sensor on the engine. If there are codes that say ratio error, take it back to who rebuilt it and hope they will take care of you. I use to give a major discount if they were not too far out of warranty.

Posted on Jan 09, 2010

Testimonial: "the information i recieved was what i was thinking it might be,either a speed sensor or a related computer problem Thanks for your input."

vetteman3002
  • 2299 Answers

SOURCE: i have a 90f-150 and

This sounds like the problem is still in the torque converter. It sounds like the torque converter is locking up too early. And causing the jerking. It also could be the PCM. But if the torque converter has been a problem then I would look there first. Take the truck back to the company that rebuilt the torque converter and have them repair the problem.

Posted on Nov 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 mercury Cougar is in park; tried several times to move it out of gear and no luck. Tranny fluid full. A few months ago had tranny fluid pan gasket replaced. Has been driving fine up til today.


If it's stuck in park , problem with gear interlock system ! This is a safety system that will not allow gear shifter to be move with out foot pressing on the brake pedal . Do the brake light's work ? Could be a bad switch or wiring problem or shift interlock solenoid or maybe even a control module ! http://autoshop101.com/forms/h18.pdf

Feb 11, 2017 | Mercury Cougar Cars & Trucks

2 Answers

02 grand Cherokee 4.7 545ref tranny 247transfer case if transfer case is bad would it make it seem like the tranny was bad I have no gears tranny rebuilt 8 months ago, it will try to go if u rev throttle...


You will have to have the transmission issues diagnosed

I would not think your question is directly the main issue, as
far a the transfer case goes,but it still can have mechanical
& electrical problems

If you have been using it like that & most people do, then
having been a trans shop owner, you could very well have
ruined yet another unit,way I don't know

I would guess the trans was possibly not updated or built
properly & I have seen them fail in 8 months

Sometimes you find a mistake or problem & in most cases
they are as clean inside as the day you rebuilt it

Today most issues are electronic & good luck there finding
a tech who knows the complete powertrain

You can not just start at the trans or transfer case

You have to diagnose every module in the vehicle
& all systems & fix as you go,even if is just trans related

The cold can effect the valve body until warmed up

Could be it was never taken apart or cleaned

Could be as you said, the shop didn't know how
to take the pump apart or even check for updates
to valves in there that score the pump

Nov 25, 2014 | Cars & Trucks

1 Answer

1995 chevy tahoe wont go into no gears but has reverse


na these trucks are known for tranny problems im on my 6 th tranny with396000 miles

Mar 21, 2013 | 1995 Chevrolet Tahoe

1 Answer

LOUD WHIRRING NOISE FROM CHEVY BLAZER TRANNY


It sounds more like the pump, if the converter fails it would have a crazy lock up shifting problem. Sometimes the bearing for the torque converter will loosen and spin in the housing this to could be the issue.

Aug 04, 2009 | 2001 BMW Z3

1 Answer

I have an 04 Silverado with the 4L60E. The


I would be interested to know why you kept pulling the tranny. Its possible you lost the prgram in the PCM. You may need a reflash. Where there codes. Or you may have a bad torque converter or trans oil pump.

Jul 15, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

94 Chevy Silverado 4L60E Trans. Lost all drive gears


Internal gear selector in Tranny is shot...try replacing with used..or get to a tranny shop..Good luck

Jun 16, 2009 | 1994 Chevrolet C1500

1 Answer

Will not shift to 2 gear


If you keep accelerating will it catch third or does it stay in 1st? Does it **** hard when you put it in gear?

Mar 14, 2009 | 1984 Chevrolet K2500

1 Answer

1998 ford ranger 3.0 motor auto.transmission slips driven cold


what is the (revolutions per minute) rpm of your engine when the torque converter engages, was the torque converter rebuilt too? what type torque converter is in the ford ie low stall where it engages the gear box at around 900 to 1000 rpm. has there been any power band adjustment by the company that rebuilt your automatic transmission after the insallation.

Jan 02, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Stalling


Have you done a back pressure test on it? If you have no idea what I'm talking about, unbolt exhaust at heads or before the catalitic converter/converters. Try starting then driving it then. If that solves your problem, your catalitic converter/converters are clogged.

Sep 19, 2008 | 1983 Oldsmobile Cutlass Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...