Question about 2006 Ford Freestyle

1 Answer

<!-- from fixya rte -->Replace heater air conditioning filter - 2006 Ford Freestyle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,313 Answers

Parts stores often have a part location diagram which may help. These filters are often behind the glove box, which may have to be removed to get at it, but sometimes are below it. Some are located under the hood in the passenger cowl area and require removing a panel to access. If all else fails, call a dealer parts department. Some are quite helpful.

Posted on Nov 25, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford Taurus 2007 air condition is OK, however I get cold air when heater is turned on. Antifreez level is OK.


replace thermostat before you do anything else.. If it is stuck open there will be not heat

Sep 09, 2014 | Ford Taurus Cars & Trucks

1 Answer

2001 Chevy blazer air conditioning blower is throwing very little air. what and how I can get it back to normal?


Is the issue there when using heat and air-con?
If so, then check the blower motor and fan switch for fault.

Check any cabin air filter if fitted for clogging.

If only an issue with hot air flow, then check the heater matrix hasn't bunged up.

If only a cold air flow, then check the air conditioning car evaporator in the cabin for signs of clogging.

Clogging can be more of an issue in pet owner's cars as pet hair readily clogs up these two components in cars fitted with no interior air cleaner element/filter.

Nov 05, 2012 | Cars & Trucks

1 Answer

2007 Chrysler 300. When outside temperature is below 30 degrees, I cannot keep the windows clear of moisture and fog. Even the defroster on high has difficulty clearing and keeping the windows clear. I do...


If your car has an air conditioner turn it on as well as the heater . Air conditioned air is very dry and usually defrosts the windscreen quickly. The heat from the heater will overcome the cold air from the air/con. It is good for the air/con to be run during the winter months as well as summer, it stops the seals drying out and leaking refrigerent.

Apr 05, 2011 | 2007 Chrysler 300 AWD Sedan

1 Answer

Needto replace heater core in 99 ford taurus,need help


Instructions Things You'll Need:
  • Replacement heater core
  • Clean container
  • Wrench
  • Screwdriver
  • Steering wheel nut
    Removal
  1. Disconnect the negative battery cable and wait at least one minute for the air bag system to lose power. Make sure the front wheels are straight ahead and lock the steering column.

  2. Detach the air bag module by removing the bolts from underneath both sides of the steering wheel and the electrical connector. Remove the steering wheel bolt and press the wheel away from the steering column. Remove the lower steering column cover.

  3. Insert a 1/8-inch wire or pin punch in the shroud hole under the ignition switch while it's in the "Run" position. Press on the pin and pull on the ignition switch lock cylinder to remove it.

  4. Disassemble and remove the instrument panel from the Taurus' interior. This includes the radio and all panels, electrical connectors, harnesses and screws. You'll need an assistant to help you lift and remove the instrument panel.

  5. Drain the engine coolant from the cooling system, using a clean container for reuse. Remove the heater hoses, actuator and metal cover from the heater. Disengage the spring from the heater core cover and the lever.

  6. Depress the locking ramp and remove the lever from the secondary air temperature control (the lever is brittle, so don't bend it). Remove the primary air conditioning air temperature control door shaft from the pin.

  7. Remove the heater core cover and seal from the heater/air conditioning housing assembly. Remove the heater core from the heater/air conditioning housing by pressing on the core tubes and assembly.

  8. Installation
  9. Install the replacement heater core to the heater/air conditioning housing. Install the core cover, seal, lever, spring, metal cover, actuator and heater hoses.

  10. Replace and assemble the instrument panel with your assistant's help. Connect the steering wheel (use a new bolt to connect it to the column), air bag and negative battery cable.

  11. Refill the cooling system with either the old coolant or new. Start the Taurus' engine and let it reach normal operating temperature. Watch the climate control operation and check for any leaks.



Read more: How to Replace the Heater Core in a Ford Taurus ' eHow.com http://www.ehow.com/how_4521301_replace-heater-core-ford-taurus.html#ixzz132BljfG8

Oct 21, 2010 | Ford Taurus Cars & Trucks

3 Answers

Looking to replace heater core


Cherokee, Grand Cherokee, 1999-2005

Removal & Installation
  1. Disconnect and remove the negative battery.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument.
  2. Drain the cooling system into a clean container for reuse.
  3. Remove the instrument panel by performing the following procedure:
    1. Turn the steering wheel in the straight-ahead position.
    2. Remove the knee blocker from the instrument panel.
    3. Remove the steering column; do not remove the air bag module, the steering wheel or switches from the steering column.
    4. From under the driver-s side of the instrument panel, disconnect the following items:

      Instrument panel wiring harness connector from the 100-way wiring harness connector at the left side of the inner panel. Side window demister hose at the heater/air conditioning housing demister/defroster duct on the driver-s side.
    5. Remove the glove box.
    6. Reaching through the glove box opening, disconnect the following items:

      Two halves of the heater/air conditioning system vacuum harness connector. Instrument panel wiring harness connector from the heater/air conditioning system wiring harness connector. Instrument panel wiring harness connector from the passenger-s side air bag module wiring harness connector. Side window demister hose at the heater/air conditioning housing demister/defroster duct (passenger-s side). Two halves of the radio antenna coaxial cable connector. Two instrument panel wiring harness connectors from the passenger air bag ON/OFF switch wiring harness connector. Passenger-s side air bag ON/OFF switch wiring harness from the retainer clip on the plenum bracket that supports the heater/air conditioning housing just inboard of the fuse block module. Two lower passenger-s side air bag module bracket-to-dash panel nuts.
    7. Remove the upper cover from the instrument panel.
    8. Remove the 3 instrument panel-to-door hinge pillar screws.
    9. Remove the 4 upper instrument panel-to-dash nuts.
    10. Using an assistant, remove the instrument panel from the vehicle.
  4. If equipped with air conditioning, discharge and recover the air conditioning system refrigerant.
  5. Disconnect the refrigerant lines from the evaporator. Plug the refrigerant openings to prevent evaporation.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Disconnect the heater/air conditioning system vacuum supply line connector from the T-fitting near the heater core tubes.
  8. In the engine compartment, remove the 5 heater/air conditioning housing-to-chassis nuts. If necessary, loosen the battery hold-downs and reposition the battery for access.
  9. Remove the cowl plenum drain tube from the heater/air conditioning housing stud; it-s located behind the cylinder head on the cowl.
  10. From the bottom of the heater/air conditioning housing, remove the floor duct.
  11. On the passenger side, remove the heater/air conditioning housing-to-plenum bracket screw.
  12. Pull the heater/air conditioning housing down far enough to clear the defrost/demist and fresh air ducts, then, rearward far enough to clear the mounting studs and the evaporator drain tube to clear the dash panel holes.
  13. Remove the heater/air conditioning housing assembly from the vehicle.
  14. Remove the heater/air conditioning housing upper case.
  15. Lift the heater core from the lower half of the heater/air conditioning housing.
To install:
  1. Assemble the heater core into the lower half of the heater/air conditioning housing.
  2. Install the heater/air conditioning housing upper case.
  3. Install the heater/air conditioning housing assembly to the vehicle.
  4. On the passenger-s side, install the heater/air conditioning housing-to-plenum bracket screw.
  5. At the bottom of the heater/air conditioning housing, install the floor duct.
  6. Install the cowl plenum drain tube to the heater/air conditioning housing stud; it-s located behind the cylinder head on the cowl.
  7. In the engine compartment, install the 5 heater/air conditioning housing-to-chassis nuts.
  8. Connect the heater/air conditioning system vacuum supply line connector to the T-fitting near the heater core tubes.
  9. Connect the heater hoses to the heater core tubes.
  10. Connect the refrigerant lines to the evaporator.
  11. If equipped with air conditioning, evacuate and charge the air conditioning system refrigerant.
  12. Install the instrument panel by performing the following procedure:
    1. Using an assistant, install the instrument panel to the vehicle.
    2. Install the 4 upper instrument panel-to-dash nuts.
    3. Install the 3 instrument panel-to-door hinge pillar screws.
    4. Install the upper cover to the instrument panel.
    5. Reaching through the glove box opening, connect the following items.

      Two lower passenger-s side air bag module bracket-to-dash panel nuts. Passenger-s side air bag ON/OFF switch wiring harness to the retainer clip on the plenum bracket that supports the heater/air conditioning housing just inboard of the fuse block module. Two instrument panel wiring harness connectors to the passenger air bag ON/OFF switch wiring harness connector. Two halves of the radio antenna coaxial cable connector. Side window demister hose at the heater/air conditioning housing demister/defroster duct (passenger-s side). Instrument panel wiring harness connector to the passenger-s side air bag module wiring harness connector. Instrument panel wiring harness connector to the heater/air conditioning system wiring harness connector. Two halves of the heater/air conditioning system vacuum harness connector.
    6. Install the glove box.
    7. Under the driver-s side of the instrument panel, connect the following items:

      Side window demister hose at the heater/air conditioning housing demister/defroster duct on the driver-s side. Instrument panel wiring harness connector to the 100-way wiring harness connector at the left side of the inner panel.
    8. Install the steering column.
    9. Install the knee blocker to the instrument panel.

  13. Connect and remove the negative battery.
  14. Refill the cooling system.
  15. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Hope helps (remember rated this).

Jun 25, 2010 | 2001 Jeep Grand Cherokee

1 Answer

2001 ford focus defroster blows out ac vents


may be just a cable adjustment.


SECTION 412-01: Air Distribution and Filtering 2001 Focus Workshop Manual DESCRIPTION AND OPERATION Air Distribution and Filtering The new heating and ventilation system ensures even air distribution.
The temperature control and air distribution flaps are controlled by two operating cables. All vehicles have a recirculated air function, with the flap controlled by a servo motor.
Air is supplied to the windscreen and side windows regardless of the air distribution setting.
The clean air filter is fitted as standard in most countries. This cleans the incoming fresh air of pollen and dirt particles. It must be renewed after every 40,000 km under normal operation conditions, or after 20,000 km under difficult conditions. If no clean air filter is installed, a plastic grille is fitted over the air intake. This can easily be replaced with a clean air filter.
Air distribution operating switch
Face level The main flow of air enters the passenger compartment at face level.
Face level/floor level The main flow of air enters the passenger compartment in equal parts at face level and floor level, and a small amount flows to the demister nozzles of the side windows.
Floor level The main flow of air enters the passenger compartment at floor level, and a smaller amount flows to the demister nozzles of the side windows.
Demist/floor level The main flow of air enters the passenger compartment in equal parts at the windscreen and at floor level, and a smaller amount flows to the demister nozzles of the side windows.
Demist The main flow of air enters the passenger compartment at the windscreen and a smaller amount flows to the demister nozzles of the side windows.
Air distribution operating switch Air distribution operating cables
NOTE: The Bowden cables for LHD and RHD vehicles are identical. However, they are fastened to the air flap operating mechanism with the respective reverse side of their connectors.
The air distribution switch operates with two Bowden cables. The cables operate the air distribution valves in the heater housing.
To remove and install the cables, the rotary switch must be turned as far as it will go to the left. The air flap mechanism engages easily in this position, making the installation of the cables easier.
--------------------------------
Air Distribution Cable Control Assembly Removal
s1y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the radio/cassette unit and the CD player (if equipped). For additional information, refer to Section 415-01 .
  1. Remove the bezel with heater/air conditioning controls.
  1. Remove the bezel with heater/air conditioning controls (continued).
    • Pull off seven electrical connectors (six shown).
  1. NOTE: To remove the Bowden cables, turn the rotary switches as far as they will go to the left.
    Remove the bezel with heater/air conditioning controls (continued).
    • Unclip the Bowden cables.
  1. Remove the lower driver's side footwell trim.
  1. Unclip and remove the air distribution Bowden cables.
  1. Unclip and remove the temperature control Bowden cables.
    • Unclip and remove the temperature control Bowden cables.
Installation
  1. NOTE: Route the new Bowden cables without kinks and check for easy accessibility.
    NOTE: To install the Bowden cables, turn the rotary switches as far as they will go to the left. The mechanism engages easily in this position.
    NOTE: The Bowden cables are identical for RHD and LHD vehicles, although they are fastened to the air flap operating mechanism with the reverse side of their connectors.
    Install the components in reverse order.
  1. Check operation of the Bowden cables.

Mar 17, 2009 | 2003 Ford Focus

1 Answer

Difference between an Air Filter and Air Conditioning filter


The air conditioning filter that your manual speaks of is known as a ''cabin filter'', it is much differant then your engine air filter. It filters the incoming air into your vehicles interior. So if someone has told you to replace your ''air filter'' they are more then likely speaking of your ''engine'' air fitler. You should check your engine air filter every oil change. If it shows signs of dirt, then replace it. Hope this helps =)

Mar 12, 2009 | 2003 Toyota Land Cruiser

1 Answer

99 Bonneville SE


Does not have a heater fan filter, only a air filter,oil filter and a trans. filter. oil filter change every 2500 to 3000 miles- air filter depends upon driving conditions it should be inspected at time of oil change- and trans. filter changed every 30 to 35,000 miles

Jan 26, 2009 | 1998 Pontiac Bonneville

Not finding what you are looking for?
2006 Ford Freestyle Logo

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...