Question about Cars & Trucks

1 Answer

<!-- from fixya rte -->How can a sensor be cleaned and replaced? - Cars & Trucks

Posted by on

1 Answer

On your kitchen stove ?

Posted on Nov 17, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I try cleaning sensor on bank one of a 2005 Camry with 2.4l


Cam and crankshaft sensors are magnetic so cleaning them would be a waste of time, you can replace them which would eliminate them being faulty! O2 sensors are non-serviceable thus making them in able to be cleaned! Cars today have no serviceable parts and only can be replaced!

Mar 07, 2015 | 2005 Toyota Camry 2.4

1 Answer

2000 lexas rx 300, replaced the o2 sensors but engine lght and code is still 171,could there be a vacumn leak and the sensors are telling the computer [lean on left bank]?


I'd clean or replace the MAF sensor (Mass Air Flow). You can pick up a can of MAF sensor cleaner at most auto parts stores. Replace if cleaning does not work. Go from there...

Jul 03, 2013 | Cars & Trucks

2 Answers

Can the oxygen sensor be cleaned


The upper and heated O2 sensors should not be cleaned as depending on the cleaner, can destroy them anyway, and the right cleaner for the component can't clean them well enough. It's best to buy new if the ECU kicks out 02 sensor code errors.

Apr 08, 2013 | 1998 Lincoln Navigator

1 Answer

Anti lock brake light stays on


gm is known for their anti-lock brake problems the most likely problem is a build up under the sensor since u have a 93 the abs sensor is incorporated into the hub cheaper to replace the hub w/sensor than to just replace the sensor the hub is not that hard to replace in the 2wd or 4wd----to clean mount jack up vehicle remove the wheel brake caliper,caliper bracket ,rotor and the abs sensor will be in view check the connection and the condition of sensor into the hub if lot of road grime or rust build up use a brush to clean area around sensor than using an allen key remove sensor careful pull straight up plug hole and clean small mounting plate replace sensor ------to replace hub do same in removing components but than need to unbolt hub from rear on 4wd also need to remove cv drive nut replace hub and done

Dec 07, 2012 | 1993 GMC Suburban

1 Answer

2000 mercury mountaineer 5.0 idel roung at idel at higher rpms runs fine


Air Filter-clean or replace
Clean MAF Sensor--CRC MAF Cleaner
Clean throttle plate-CRC Throttle Body Cleaner
Spark Plugs- replace every 70,000 miles
Check -for vacuum leaks on ALL ducting and hoses
Replace front 2- O2 Sensors-ones closest to motor ,every 100,000 miles

Have TPS Sensor --tested with an oscilloscope for opens

Mar 06, 2011 | 2000 Mercury Mountaineer

1 Answer

Speedometer needle is on the wrong side of the pin, so the speedometer won't work. Can you help?


I am assuming you have a 4-speed transmission?
There are 2-speed sensor on the front of the transmission. Input and Output Speed Sensors.
They are level with each other, right above the top line of the Solenoid (wiring harness goes into this box-like assembly) The one that is closest to the Solenoid is the Input Sensor. The one (at the same level) towards the left side of the van is the Output sensor.
I believe a 1-in wrench will work, after you unplug the sensors. Torque going-on for both is 20 ft-lbs. Before replacing the sensors - you may remove the sensors and clean the metal particles off the interior tips of the sensors and reinstall and check operations. Start with removal, cleaning, replacing the Output Speed Sensor as the Speedometer Info is directly involved with this. If cleaning does not fix the problem then replace it and check operations, before replacing the Input Speed Sensor. This will save you money from replacing both sensor.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at fixya.com

Dec 21, 2009 | 2003 Chrysler Town & Country

2 Answers

Hard starting.. check engine on P0101


Replace the filter but don't try and clean the MAF sensor,Just replace it.

May 09, 2009 | Nissan Maxima Cars & Trucks

1 Answer

I have an error code p1405 on my 2004 lincoln navigator - what is


DPFE Sensor upstream hose bad. Google DPFE Sensor location. Then remove and replace or clean hoses, Clean connectors at sensor. If this does not clear problem replace Sensor.

Mar 22, 2009 | 2004 Lincoln Navigator

2 Answers

Location of oxygen sensors 1996 intrepid es 3.5 litre


Oxygen sensors have to be replaced. U can clean a sensor yes with electronic spray and applying a bit of di-electric grease. But y do u want to replace it though? It is usually located on the exhaust circuitry

Jan 30, 2009 | 1996 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...