Question about 2007 Ford Freestyle Limited

1 Answer

I have a 2007 ford freestyle error code p0340 bought a new camshaft position sensor, i just dont know were it is located on the engine and how I would need to get to it, what i would have to move and

I have a 2007 ford freestyle error code p0340 bought a new camshaft position sensor, i just dont know were it is located on the engine and how I would need to get to it, what i would have to move and what not.

Posted by on

Ad

1 Answer

OBD Codes do not mean you replace parts that sound
like the name of a code

You use the codes to diagnose the system that set the fault
code & component test to find a problem

Your buying parts, when you don't know how they work
or where they even are on the motor & do not plan on
doing any testing, to find a problem, to see if a part has failed

Best you let a professional find a problem for you.

The internet is filled with pictures & video, on anything you
need to know,if you use Google correctly

Posted on Nov 18, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

  • 1206 Answers

SOURCE: I got a camshaft position sensor malfunction code P0340.

it sounds like you have bigger problems if your car does not crank(turn over) then your timing belt could have broken and the one piston could be hitting a valve causing it to be locked up.normally when any sensor is bad car engine still cranks it just doesn't start.

Posted on Jan 28, 2010

emissionwiz
  • 76164 Answers

SOURCE: where is the Camshaft Position Sensor located on a

this car has but one bank, the cam sensor is under the intake manifiold on the drivers side.

Posted on Feb 25, 2010

Testimonial: "thanks, now I know where to start looking. Is it a fairly easy item to replace?"

  • 62 Answers

SOURCE: 1998 Ford Ranger 4.0 engine

the camshaft position sensor is located In the back off the engine on top, were the distributor use to be in earlier V-6 Ford were. ( center top just ahead of were the transmission bolts up to the engine block)

Posted on Jan 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1336 trouble code ho to solve problem


P1336 Ford P1336 Ford - Crankshaft Position Or Camshaft Position Sensor Input Signal Error Share
0 ' Add Comment Possible causes
- Faulty Crankshaft Position Sensor
- Faulty Camshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected a synchronization or signal error from the cam or crank sensors
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
- Engine difficult to start
P1336 Ford Description
The input signal to the powertrain control module (PCM) from the crankshaft position (CKP) sensor or the camshaft position (CMP) sensor is erratic.

Read more: http://www.engine-codes.com/p1336_ford.html#ixzz3qT9Hiztc

Nov 03, 2015 | 2005 Ford Freestyle

1 Answer

Mustang error codes P0340 , P0344


These are camshaft position sensor codes. Replace camshaft sensor.

Apr 18, 2017 | 2006 Ford Mustang GT

1 Answer

I went to scan my toyota yaris car and the following codes were give ; temperature ckt low input po117


EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Dec 13, 2012 | 2001 Toyota Yaris

1 Answer

I changed out the MAP sensor,and the idle air sensor on my 2006 Ford Taurus. This was before I had the fault code read at a dealer. Code came back as P0340, and P0430 Band 2 cat worn out. I had the cam...


P0340 FORD - Camshaft Position Sensor Circuit Bank 1 Sensor 1Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
P0340 FORD Description The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder. The camshaft position sensor senses the piston position. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor.

When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.

When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.
P0430, main catalyst is worn out.

Dec 04, 2012 | 2006 Ford Taurus

1 Answer

P0340 99 jeep cherokee code


P0340 JEEP - Camshaft Position Sensor Circuit engine cylinder Bank 1 Sensor 1

Possible causes- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sometimes and in some models, low battery voltage or a weak starter can can trigger a Camshaft Position Sensor code.

Read more: http://engine-codes.com/p0340_jeep.html#ixzz25iQflrEb

Sep 06, 2012 | 1999 Jeep Grand Cherokee

1 Answer

Were is locat the po340 sensor


P0340 - Camshaft Position Sensor Circuit Malfunction
This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms can include:
* Hard starting or no start
* Rough running / misfiring
* Loss of engine power

Causes
A code P0340 could mean one or more of the following has happened:
* a wire or connector in the circuit could be grounded/shorted/broken
* the camshaft position sensor may have failed
* the PCM may have failed
* there exists an open circuit
* the crankshaft position sensor may have failed

Possible Solutions
With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Visually inspect all the wiring and connectors in the circuit
* Check for continuity in the circuit wiring
* Check the operation (voltage) of the camshaft position sensor
* Replace the camshaft position sensor as required
* Check the crankshaft position circuit as well
* Replace circuit wiring and/or connectors as required
* Diagnose/replace the PCM as required


The Cam Position Sensor is located on the drivers side; the intake manifold is cut out where is sits on top of the engine block. Its black in color and has two 5.5 mm. screws that you'll be able to see.

Hope helps.

Apr 03, 2011 | 2000 Ford Taurus

1 Answer

P0340 Code Camshaft Position Sensor



The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Jan 17, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

Error Codes P1684 and P0340


P0340
Camshaft position sensor circuit
  • Most likely cause : Camshaft position sensor failed.
-----------------------------------
P1684
means the battery was disconnected(or had been drained to a low voltage) recently.


Jul 22, 2008 | 2001 Dodge Stratus

Not finding what you are looking for?
2007 Ford Freestyle Limited Logo

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...