Question about 2005 Mitsubishi Montero

1 Answer

How do I remove second row seat?

Remove second row seat

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 18 Answers

What type of vehicle are we talking about?

Posted on Nov 20, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do do you remove and install passenger seats


then perhaps you need to take it to a dealer and have them done correctly .

Feb 17, 2016 | Cars & Trucks

1 Answer

Remove center seat belt in second row 2005 Cadillac srx


Remove the rear lower seat. Remove bolts holding belts to floor pan of vehicle.

Mar 06, 2015 | 2005 Cadillac SRX

1 Answer

How do I remove second row seat


If its on rails, pull the handle and slide it off. If no rails pull really hard from the top or kick from the back. Check for bolts behind and underneath the carpet, it may have a couple fasteners. You can really beat on a seat and it will take it. Sometimes that's what you gotta do.

Nov 17, 2014 | 2005 Mitsubishi Montero

1 Answer

How can I remove second row bucket seats


They are bolted to the floor. There are plastic covers over the base of the seats on the floor. Remove the covers then unbolt the seats to remove.

Jul 20, 2014 | 2014 Toyota Sequoia

1 Answer

I have a 2001 chrysler voyager where is the blend door actuator located and how to remove it


its in the HVAC heater core box,
how to remove it is a very long answer.
read the FSM on HVAC
or login to alldata.com see HVAC chapter, and read. it.
anyone can, not just me.

i see this on line,.
  1. Disconnect and isolate the battery negative cable.
  2. Remove first row seat.
  3. Remove second row seat.
  4. Remove sliding door sill trim panel.
  5. Remove quarter trim bolster.
  6. Remove D-pillar trim panel.
  7. Remove first row seat belt anchor.
  8. Remove second row seat belt anchor.
  9. Remove screws attaching quarter trim to quarter panel from bolster area.
  10. Remove screws attaching rear edge of quarter trim to attaching bracket.
  11. Disengage hidden clips attaching front of quarter trim to quarter panel rearward of sliding door opening and at locators.
  12. Remove quarter trim from quarter panel.
  13. Disconnect speaker wire connector on LWB quarter trim panel with rear air conditioning.
  14. Pass second row seat belt through slot in trim panel on long wheel base vehicle.
  15. Pass first row seat belt through slot in trim panel.
  16. Remove quarter trim panel from vehicle.
  17. Remove the two screws that secure the top of the quarter trim panel attaching bracket to the quarter inner panel.
  18. Remove the screw that secures the back of the rear heater-A/C unit housing to the right D-pillar.
  19. Remove the screw that secures the front of the rear heater-A/C unit housing to the right quarter inner panel.
  20. Carefully pull the top of the rear heater-A/C unit housing away from the right quarter inner panel far enough to reach between the rear heater-A/C unit housing and the quarter inner panel to access the blend door actuator.
  21. Remove the two screws that secure the blend door actuator to the rear heater-A/C unit housing.
  22. Pull the blend door actuator away from the rear heater-A/C unit housing far enough to disengage the actuator output shaft from the blend air door pivot.
  23. Raise the blend door actuator far enough to access and disconnect the rear HVAC wire harness connector for the actuator from the actuator connector receptacle.
  24. Remove the blend door actuator from between the rear heater-A/C unit housing and the quarter inner panel.

May 21, 2014 | 2001 Chrysler Voyager

1 Answer

2nd row seat of my ford excursion seat went down but I can't get it to release and return to an upright position


cabling inside the seat is faulty ,,,,, nasty problem as you have to remove upholstery to repair it ,,,,,

Dec 06, 2013 | 2002 Ford Excursion

1 Answer

Remove seat from second row in Honda Mini Van 2007


on the passenger side feel under the seat and there is a lever that pulls toward you as you stand at the sliding door.

First, raise the armrest, then lower the back all the way forward. Then remove the headrest sit it out of the way and while pulling the lever under the seat towards you, lift up the seat from the back so it tilts forward. When it is standing on its "nose" lift first one side shifting it either forward or backwards to clear the rod on which it is hooked. Do the same with the other side of the seat and then lift it out. Installation is the reverse of removal.

The other seat is much the same, though sometimes the lever is a little different but in the same place.

Good luck,
bob

Jun 07, 2009 | 2006 Honda Odyssey

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge...


the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.
  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in the upright position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Mar 02, 2009 | 1997 Mercury Villager

1 Answer

Removing the 2nd and 3rd row seats


3rd row, you simply pull the lever which makes the back fold down and then grip the handle located on the bottom and pull toward you slightly hard. They are heavy so it seems like they aren't coming out, just pull hard. second row, you flip all the way up and push with them standing up and they come unhooked. Good Luck! I didn't have any problems, except they are at least 50+lbs!

Nov 18, 2008 | 2007 GMC Yukon

Not finding what you are looking for?

Open Questions:

See all 2005 Mitsubishi Montero Questions

Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...