Question about 2005 Hyundai Matrix 1.6

Open Question

How do I remove the malfunction indiator panle

The panel that has the malfunction light

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

INSIDE DOOR HANDLE IS BROKEN HOW DO YOU REMOVE THE PANLE DRIVER SIDE DOOR


You will have to remove the covers and lights off of the door. Pop of the lenses on the lights and there will be screws to remove the light fixture. The cover for the handle will be a snap in or one screw. The lock will screw off or pull off. Once you have all of he accessories off then you can work the edges of the door panel by pulling. They are held on by snap in clips at this point.

Mar 09, 2016 | 2010 Lincoln MKZ

1 Answer

HOW DO YOU REMOVE DOOR PANLE DRIVER SIDE


Courtesy of expert Chuck Martin.
Snap out two door pull strap retaining screw covers. Remove screws.
Remove screws on front, rear and center of front door trim panel.
Using the Trim Pad Removing Tool or equivalent, pry the trim panel retaining clips from the door inner panel.
These are plastic so be careful you can use a pair of needle nose pliers if you don't have a trim tool.Just start at bottom of door panel and work your way around and up

Mar 09, 2016 | 2010 Lincoln MKZ

1 Answer

Malfucnction Indiator lamp


The malfunction indicator lamp(MIL) indicates a faulty sensor/s in the ECM system management. If it is flashing it will be a code as to the fault and the faults can be read by a scanner to determine the nature of the fault. Once the fault has been fixed then a scanner can be used to reset the MIL

May 31, 2014 | Pontiac G6 Cars & Trucks

1 Answer

Fuse panle ford fuses to go to what. the lay out on the fuse panle to what the fuses go to


The fuse panel layout is in the operaters manual in the glovebox,without you will be lost.If you don't have one,get one from the dealer.

Mar 17, 2011 | Ford Focus Cars & Trucks

1 Answer

How do I replace the dimmer switch?


remove fuse panel on side of dash take two screws out remove light swich if pull type push spring trowds the front of the switch and pull the knob off if pus type remove panle it snaps into place and remove screws for dim switch

Jan 16, 2011 | 1991 Buick Park Avenue

1 Answer

I am trying to locate the passenger side fuse panel


Hello
Open the passenger frunt door,, Where the corner of the dash sits out in the open when the door is open there is a small cover here,pull on where you can put a finger in the panle and the panle will come off , The panel snaps back into place,

Jul 16, 2010 | 2000 Dodge Durango

1 Answer

The handle broke off on my 2003 jeep grand cherokee laredo liftgate. how can i open it now? i can't find anything on the inside in the back and my tail light is out.


You will need to remove the interior panle from the loft gate to axess the latch
there is 4 screws along the bottom of the panle to remove then carfuly pull the panle away from the lift gate there is plastic clips that hold the panle to the gate these may need to be replaced when re installing the panle they can be purchased at the jeep dealer.
now look into the lift gate and you will see where the handle rod conects to the latch lift on this rod and the gate will open
to replace the handle remove the 2 10 mm bolts and disconect the rod from the latch install the new handle and rod to the latch install the 2 10 mm bolts. install the panle and 4 screws
this should cover it

Jul 13, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Both passenger doors wont open, who do i remove door panle


you will have a hard time removing the door panel if the door will not open you may end up breaking the panel you maybe better off taking to a trim place
hope this helps

Nov 07, 2009 | 1998 Buick Park Avenue

2 Answers

Removal of interior door pannel on left rear door


Normal 0 Quite simple. Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.

May 30, 2009 | 2001 Cadillac Seville

1 Answer

REAR DRIVER'S SIDE DOOR PANEL


There are most likely a couple of screws mabye hidden under a little plug or plastic cover around the door handle and on the under side of the panel.Then if it is a crank style window you will have to remove the window crank handle,after that there are plastic panle pop clips you will just have to pull on panle and they should pop out,then lift the panle up off the window door seal.

Aug 30, 2008 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
2005 Hyundai Matrix 1.6 Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...