Question about Cars & Trucks

Open Question

Bell b20d dumper,hard starting need to prime pump before it can start

Bell dumper truck, Mercedes benz motor

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 408 Answers

SOURCE: Wiring diagram of window wiper motor on 1994 Mercedes Benz 320

hello,can you post your chassis number,so i could help you regarding your wiper motor,because 1994 model have different version,ty

Posted on Apr 16, 2009

  • 11 Answers

SOURCE: '89 benz 300e, hard to turnover when starting, fuel pump/filter?

Run some Sea Foam Through it you tube sea foam It works

Posted on Apr 27, 2009

  • 160 Answers

SOURCE: won't start, replaced starter and still won't start

could be flooded or clogged fuel injecters

Posted on May 09, 2009

  • 1596 Answers


Ignition Timing is Most Common Mistake for this Repairs No Start Problem

Posted on Oct 04, 2009

Testimonial: "info was very helpful"

  • 8404 Answers

SOURCE: Mercedes Benz car will not shift out of park. It

You are putting your foot on the brake before you try to move the shift lever, right?

Most cars have a locking device that prevents the shifter from moving unless the motor is running (key inserted into the wheel lock and on) and the brake petal is depressed.

Posted on Jan 02, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need to know what size bell houseing bolts i need for my transmission

I take it you have lost all the original bolts. Best trick would be to measure the approx size of the holes and get a few close sizes from hardware store (grade 5 or better). Test each until you find correct thread pitch (should be coarse). Next, measure total depth of hole and thickness of bell housing and select bolt with washer that lacks 1/8th to 1/4 of bottoming out.

Jun 04, 2015 | 1991 Mercedes-Benz Mercedes Benz Sl Class

1 Answer

Where is the crank sensor on a 94 Mercedes s420

drivers side top of the transmission bell housing. usually can be accessed from on top behind left cylinder head.

Sep 13, 2014 | 1994 Mercedes-Benz S-Class

1 Answer

Location of crank sensor

top left of transmission bell housing at rear of engine.

Apr 08, 2014 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

Oil leakage on Mercedes Benz 5.0L engines

oil in the bell housing can be rear main seal and it can also be input shaft seal in the gear box if manual. The sump bolts on the rear main cap and will leak next to the bell housing indicating a main seal . If auto then the seal on the converter will leak and the oil will leak out of the bell housing. If you are convinced that it is a main seal then check that there is no crankcase pressure issues to make it leak. Change the engine oil and clean the area and if the oils is clean then that will indicate engine or gear box. Put a white chalk line across any oil paths and watch for it to cross the chalk and change the chalk colour.

Nov 15, 2013 | Mercedes-Benz Cars & Trucks

1 Answer

Mercedes benz E200 2006 (E211). My mercedes benz

ekectric components are gittn hot from wear--ignition and fuel pump are common with age--need to do test to confirm

Oct 19, 2013 | Mercedes-Benz Cars & Trucks

1 Answer

The fuel pump looses prime and will not start

Where is your fuel pump, in the tank or on the engine? If its an external fuel pump with a fuel filter
between the tank and fuel pump, it may be a bad fuel filter.

Mar 04, 2011 | Mercedes-Benz E-Class Cars & Trucks

1 Answer

How to remove a starter from a 1996 mercedes c280

Disconnect battery ground cable first, for replace stator motor you must need to lift up the car for get space to go under the car stator motor at left side the engine, then remove under cover of engine compartment, after that you can see the stator motor behind the left side engine mount, then remove main wire from stator motor and also solenoid wire, next remove two bolts for stator motor from bell housing and pull stator motor out and take out between trans mission and chassis rail you can see where you can get space to take it out, when you install back do the reverse order. is this information helped you? if yes please leave a comment.

Oct 16, 2010 | 1996 Mercedes-Benz C-Class

1 Answer


Fuse on drivers side strut mount in a tootsie roll sized case. If not blower motor or the regulator underneath it need replaced.

Aug 20, 2010 | 1992 Mercedes-Benz Mercedes Benz 400 Class

1 Answer

Where is the crank senor located on a mercedes benz clk 430

crank position sensor is located on the transmission bell housing on the drivers side of the vehicle.

Jul 19, 2010 | 2001 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides