Question about Cars & Trucks

1 Answer

How to remove a driver side fender on a 2005 dodge durango

I'm trying to remove my driver side fender on my 2005 Dodge Durango can you tell me how or send me a diagram on how to do it I removed all the screw I see and it still won't budge

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

There are 1 or 2 under the fender up by the head light. There is 1 in the door jam behind the felt cover and 2 at the bottom of the fender by the door

Posted on Nov 16, 2014

  • Nick Ours Nov 16, 2014

    Do I need to remove the bumper to get to the one under the headlight?

  • Randy Ohler Nov 16, 2014

    No, but you do have to remove the plastic inner fender well.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 217 Answers

SOURCE: getting rear gears out of the difential case 1999 dodge durango

  1. Raise and support vehicle. Ensure that the transmission is in neutral.
  2. Remove wheel and tire assembly.
  3. Remove brake drum. Refer toBrakes, for proper procedure.
  4. Clean all foreign material from housing cover area.
  5. Loosen housing cover bolts. Drain lubricant from the housing and axle shaft tubes. Remove housing cover.
  6. Rotate differential case so that pinion mate gear shaft lock screw is accessible. Remove lock screw and pinion mate gear shaft from differential case
  7. Push axle shaft inward and remove axle shaft C - clip lock from the axle shaft
  8. Remove axle shaft. Use care to prevent damage to axle shaft bearing and seal, which will remain in axle shaft tube.
  9. Inspect axle shaft seal for leakage or damage.
  10. Inspect roller bearing contact surface on axle shaft for signs of brinelling, galling and pitting. If any of these conditions exist, the axle shaft and/or bearing and seal must be replaced

Posted on Feb 11, 2009

  • 116 Answers

SOURCE: egr valve dodge durango

if this is a 4.7l engine, the valve is on the left rear of the intake. loosen the 8mm bolts that hold the egr intake tube to the egr valve, remove the egr bolts, disconnect wiring, remove valve and tube together, attach intake tube loosely to new valve, install new valve, tighten tube bolts to egr using a swivel socket, this is not a 5 minute job, so dont attempt unless you have some time and patience.

Posted on Apr 24, 2009

  • 145 Answers

SOURCE: 1999 Dodge Durango driver side window does not roll up nor down.

Remove the door panel and find the window motor Unplug it and using a separate car battery run cables directly to the window motor When you switch the polarity the motor will either bring the window up or down or if noting happened change the window motor and window regulator assembly.

Posted on Jun 08, 2009

  • 593 Answers

SOURCE: Remove headlight assembly from a 2001 Dodge Ram

On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Posted on Apr 10, 2010

  • 1 Answer

SOURCE: How do you remove the front shocks on a 2004 Dodge Durango 4X4?

how do you remove the front shocks on a 2004 durango limited 4x4. the stabilizer bar and axle links appear to be the way for removing the lower shock mounting bolt

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What years interchange with a 1999 dodge durango driver's side doors


William, 1999 Dodge Durango, years for drivers door interchange are 1998 to 2000. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Aftermarket Dodge Durango Hood Door Fender Grille Etc Prices Reviews News...
How to Remove Replace Front Door Panel 99 Durango 98 03
https://answers.yahoo.com/question/index?qid=20100413095252AADPNfw

Jun 04, 2016 | 1999 Dodge Durango

1 Answer

2005 dodge Durango rear door hatch won't open. how do I fix this?


Most of them I fix, the latch is bad. It's electrical. Some times it the wires. Usually the wires break at the top where the wires go from the door to the body. First climb in the back and see if there is a plug at the bottom/center of the door panel. If there is, remove it and use a screw driver, go left to right and catch the latch arm to release the door. If not, them remove the upper door panel around the window. It pops off. Start at the sides, the the top. Remove the screws on both side of the bottom piece(hidden by the top piece). Then pop the top of the bottom piece off. You wont get it out because there are screws on the bottom. Then you have to reach down and find the release arm and open the door to finish taking the panel off. Remove the bolts for the latch and replace it. Check the wires first. You will need a volt/ohm meter to check for power and ground.

Nov 04, 2014 | 2005 Dodge Durango Limited

1 Answer

Remove fender


Loosening the black plastic fender skirt by removing a couple of screws and pulling it out of the way shouldgive you access to the screw. Rmoving it probably won't be too much of a chore.

Feb 14, 2014 | 2000 Dodge Durango

2 Answers

How do I replace the driver side fender on my 2012 dodge journey?


remove fender you have to raise vechicle remove wheel. remove splash shield remove bolts holding fender through wheel opening.then you have open hood remove headlight housing remove fender bolts behind head light housing.

Apr 03, 2013 | Cars & Trucks

1 Answer

How do I remove the battery from a 2006 Dodge Durango?


One side of that battery will have a single 13 mm bolt that you can loosen and or remove entirely to allow you to remove that battery. Screws located down near the bottom of the battery.
The fender is on the left and then the battery and then the wedge is on the battery side which faces the engine. You need to remove it with a socket and long extension.

Remove the negative battery and place it out of the way then remove the positive cable and move it as well.Remove the heat guard or shield which surrounds the battery if installed.Remove the battery hold down wedge by unscrewing the bolt.Lift out the battery.Reverse for installation.--------------- Thank you.


Jan 31, 2011 | 2006 Dodge Durango

1 Answer

How do I install an EGR valve for 2005 dodge durango?


To install the EGR Valve on a 2005 Durango first it is necessary to remove the air intake hoses and palce them to the side. Next, in order to get the EGR valve you will need to remove the windshield wiper motor, which is a pain but necessary to do get to the EGR valve. After removing all of the itemsthat are in the way you will be faced with a task that will try your patience, the EGR valve is located on the right side of the motor, (as if you were facing the motor from the front) just behind and to the rear of the throttle body. After you locate it you will need a rachet with a flexible head because it is fairly difficult to reach otherwise. A mirror and light will also help so you can see what you are doing since the EGR valve is located in such a hard place to see and get to that you will only be able to see part of it while you are removing the screws. After removing the EGR valve, simply reversethe procedure and your done. P.S. I own a 2005 Dodge Durango SLT with a 4.7L engine and I replaced mine this year after a check engine light came on and I checked the code on the OBD. By the way the EGR valve is a pain in the rear to change. Good luck!

Jun 29, 2010 | 2005 Dodge Durango

1 Answer

Remove headlight assembly from a 2001 Dodge Ram


On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Apr 10, 2010 | 2004 Dodge Ram 1500

1 Answer

Blinkers quit working i need a diagram of the fuse box and relays where they go by driver side left leg


Remove the panel under the steering column.(three screws and pull towards seat). Look for white rectangular box with a screw in the midle of it. Remove the screw and the cover and you will find the flasher unit is located inside. Pull and replace.

Feb 17, 2010 | 1999 Dodge Durango

1 Answer

Need to replace driver side mirror on 2005 Durango Limited Editio


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Jan 22, 2009 | 2005 Dodge Durango

1 Answer

How are the front disk brakes removed on a 2005 Dodge Durango?


when you have the caliper lossened sometimes you have to depress the caliper piston to get the pads out. Use a large flat head screw driver and pry the pistons back a little. Be careful not to pry too hard. Hope this helps.

Jan 10, 2009 | 2005 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...