Question about 2002 Ford Escape

1 Answer

02 ford escape V6 what is positions of the camshaft sprocket timing marks and the crankshaft keyway

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

The camshaft and Crank mark (key way) should be pointing at each other (directly aligned with each other).
ie. The Camshaft mark will be point directly downward toward the crank and the crank mark (key way) will be pointing directly upward toward the camshaft.

Posted on Nov 16, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am changing the timing chain in a 1993 Chevy S-10 with a 4.3L engine. I was told you have to disconnect a wire to reset it but I don't know where the wire is.


Timing Chain: Service and Repair
REMOVAL
Tools Required = Crankshaft Sprocket Puller
1. Remove the timing cover.
2. Remove the crankshaft position sensor reluctor ring.
3. Remove the camshaft sprocket bolts.
4. Remove camshaft sprocket.
5. Remove timing chain.
6. Remove the crankshaft sprocket.
7. Remove crankshaft sprocket key.

INSTALLATION
1. Install the key into the crankshaft keyway.
2. Use the crankshaft balancer installer to install the crankshaft sprocket.
3. Install the camshaft sprocket and timing chain.
4. Install camshaft sprocket bolts.
Be sure to align the camshaft and the crankshaft sprocket marks. Timing marks (Number 4 Firing).
Tighten bolts to 21 ft. lbs.
5. Align the keyway on the reluctor ring with the key in the crankshaft.
6. Install the reluctor ring onto the crankshaft until the ring is completely seated against the crankshaft sprocket.
7. Install the timing cover.

Don't know what Wire you are referring to.

Jul 30, 2013 | Cars & Trucks

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

1 Answer

Timing belt is broken is a belt or chain


chain. R&R instructions from autozone.com pasted below. let me know if you have any more questions.


REMOVAL & INSTALLATION
SOHC Engine See Figures 1, 2, 3 and 4

  1. Disconnect the negative battery cable.
  2. Remove the timing chain front cover.

During timing chain and sprocket removal, position the crankshaft 90 degrees past Top Dead Center (TDC), to make sure the pistons will not contact the valves upon assembly.
  1. Carefully rotate the crankshaft clockwise so the timing mark on the crankshaft sprocket and keyway align with the main bearing cap split line (90 degrees past TDC).
  2. Remove bolts, then remove the timing guides and tensioner.
  3. Remove the camshaft sprocket bolt, using a 7 / 8 in. (21mm) wrench to hold the camshaft. Then remove the timing chain and camshaft sprocket. Remove the crankshaft sprocket, if necessary.

To install:
  1. Inspect the chain for wear and damage. Check the inside diameter of the chain, it should be no more than 16.77 in. (426mm). Inspect the chain guides for wear or cracks and the timing sprockets for teeth or key wear. Replace components as necessary.
  2. Verify that the crankshaft is positioned 90 degrees clockwise past TDC from the keyway (keyway at 3 o'clock).
  3. Bring the camshaft up to No. 1 TDC by loosely installing the sprocket and rotating the sprocket until the timing pin can be inserted. The camshaft contains wrench flats to assist in turning the shaft. The dowel pin should be at 12 o'clock when the camshaft is at TDC and a timing pin ( 3 / 16 in. drill bit) should then install at about the 8 o'clock position.
  4. If removed, install the crankshaft sprocket, then rotate the crankshaft counterclockwise 90 degrees up to No. 1 TDC (keyway at 12 o'clock).
  5. Position the chain under the crankshaft sprocket and over the camshaft sprocket. If necessary remove the camshaft sprocket, then slide the camshaft sprocket into position with the chain already engaged. The timing chain should be positioned so that one silver link plate aligns with the reference mark on the camshaft sprocket and the other aligns with the downward tooth (at the 6 o'clock position) on the crankshaft sprocket. The letters FRT on the camshaft sprocket must face forward, away from the cylinder head and excess chain slack should be located on the tensioner side of the block.
  6. Temporarily install the timing pin to verify proper alignment of the camshaft and sprocket, then install and tighten the sprocket bolt to 75 ft. lbs. (102 Nm). Again, use a wrench on the camshaft flats to hold the shaft in position while tightening the bolt. Do not allow the camshaft retaining bolt to torque against the timing pin or cylinder head damage will result.
  7. Install the chain guides with the words FRONT facing out. Install the fixed guide first and verify the chain is snug against the guide, then install the pivot guide. Tighten the bolts to 19 ft. lbs. (26 Nm) and verify that the pivot guide moves freely.
  8. Retract the tensioner plunger and pin the ratchet lever using a 1 / 8 in. No. 31 drill bit inserted in the alignment hole at the bottom front of the component. Install the tensioner and tighten the bolts to 14 ft. lbs. (19 Nm), then remove the drill bit.
  9. Make one final check to verify all components are properly timed, then remove all timing pins.
  10. Install the timing chain front cover.
  11. Connect the negative battery cable, start the engine and check for leaks.

jturcotte_7.gif

Fig. Fig. 1: At 90 degrees past TDC, the crankshaft sprocket timing mark and keyway will align with the main bearing cap split line



jturcotte_8.gif


Fig. Fig. 2: Exploded view of the timing chain and sprocket assembly-SOHC engine


jturcotte_9.gif

Fig. Fig. 3: Insert the timing pin to ensure that the camshaft is at No. 1 TDC-SOHC engine



jturcotte_10.gif

Fig. Fig. 4: When the camshaft is at TDC, rotate the crankshaft counterclockwise 90 degrees to achieve TDC

Nov 02, 2010 | 1997 Saturn SL

1 Answer

Dont no how to set the timming and what it suppose to be


Timing Chain and Sprockets
REMOVAL & INSTALLATION




  1. Fig. 1: At 90 degrees past TDC, the crankshaft sprocket timing
    mark and keyway will align with the main bearing cap split line
    84193100.gif






    Fig. 2: Exploded view of the timing chain and sprocket
    assembly - SOHC engine
    84193101.gif






    Fig. 3: Insert the timing pin to ensure that the camshaft is at
    No. 1 TDC - SOHC engine
    84193102.gif






    Fig. 4: When the camshaft is at TDC, rotate the crankshaft
    counterclockwise 90 degrees to achieve TDC
    84193103.gif


DOHC Engine

  1. Disconnect the negative battery cable.
  2. Remove the timing chain front cover.
    NOTE: During timing chain and sprocket removal, position the
    crankshaft 90 degrees past Top Dead Center (TDC) to make sure the pistons will
    not contact the valves upon assembly.



  3. Carefully rotate the crankshaft clockwise so the timing mark on the
    crankshaft sprocket and keyway align with the main bearing cap split line.
  4. Remove the bolts, then remove the timing guides and tensioner.
  5. Remove the camshaft sprocket bolts, using a 7?8 in. (21mm) wrench
    to hold the camshaft. Then remove the timing chain and camshaft sprocket. Remove
    the crankshaft sprocket, if necessary.
    To install:

  6. Inspect the chain for wear and damage. Check the inside diameter of the
    chain, it should be no more than 23.15 in. (588mm). Inspect the chain guides for
    wear or cracks and the timing sprockets for teeth or key wear. Replace
    components as necessary.
  7. Verify that the crankshaft is positioned 90 degrees clockwise past TDC. The
    crankshaft keyway should be at 3 o'clock aligned with the main bearing cap split
    line to prevent piston and valve damage.
  8. Install the camshaft sprockets, retaining bolts and washers. Make sure the
    letters FRT on the sprockets face forward, away from the cylinder block. Use the
    wrench flats provided on the camshafts to hold the shaft and tighten the bolts
    to 75 ft. lbs. (102 Nm).
  9. Bring the camshafts up to No. 1 TDC by rotating the camshafts and sprocket
    until the dowel pins are at 12 o'clock. Install a 1?6 in. drill bit
    into the hole in the sprocket about 9 o'clock.
  10. If removed, install the crankshaft sprocket, then rotate the crankshaft
    counterclockwise 90 degree up to No. 1 TDC (keyway and sprocket timing mark at
    12 o'clock, in alignment with the block timing mark).
  11. Position the timing chain under the crankshaft sprocket and over the
    camshaft sprockets so 2 silver link plates align with the reference marks on the
    camshaft sprockets and another 2 plates align with the downward tooth (at 6
    o'clock position) on the crankshaft sprocket. Excess chain slack should be
    located on the tensioner side of the cylinder block.
  12. Verify that the crankshaft reference mark aligns with the cylinder block
    mark at 12 o'clock and that the timing pins are installed in the holes at about
    the 9 o'clock position. Remove the timing pins from the camshaft sprockets.
  13. Install the timing chain fixed guide to the right of the block face toward
    the water pump. Tighten the bolts to 21 ft. lbs. (28 Nm) and verify the chain is
    snug against the guide.
  14. Install the pivoting chain guide and check for clearance between the block
    and head. Tighten the bolt to 19 ft. lbs. (26 Nm) and verify the guide pivots
    freely.
  15. Install the 2 forward camshaft bearing caps and the upper timing chain
    guide, then tighten the retaining bolts to 124 inch lbs. (14 Nm).
  16. Retract the tensioner plunger and pin the ratchet lever using a 1?8 in. (3.18mm) No.
    31 drill bit inserted in the alignment hole at the lower front of the component.
    Install the tensioner and tighten the bolts to 14 ft. lbs. (19 Nm), then remove
    the drill bit.
  17. Make one final check to verify all components are properly timed, then
    remove all timing pins.
  18. Install the timing chain front cover.
  19. Connect the negative battery cable, start the engine and check for leaks.





    Fig. 5: Rotate the crankshaft clockwise until the timing mark
    on the crankshaft sprocket and keyway align with the main bearing cap split line

    89563pb1.jpg






    Fig. 6: Loosen the timing chain tensioner mounting bolt . . .
    89563pb4.jpg






    Fig. 7: . . . and remove the tensioner from the engine block
    89563pb7.jpg






    Fig. 8: Retract the tensioner plunger and pin the ratchet lever
    with a 1?8
    in. (3.18mm) drill bit inserted in the alignment hole
    89563pb5.jpg






    Fig. 9: Remove the mounting fasteners from both timing guides .
    . .
    89563pb8.jpg






    Fig. 10: . . . and remove the timing guides from the engine
    89563pc1.jpg






    Fig. 11: Remove the camshaft sprocket bolts, using a 7?8 in. (21mm) wrench
    to hold the camshaft
    89563pc2.jpg






    Fig. 12: Remove the timing chain and camshaft sprockets
    89563pc4.jpg






    Fig. 13: Insert the timing pins to verify that the camshafts
    are at TDC
    84193146.gif






    Fig. 14: Make sure that the silver link plates and reference
    marks are all in alignment as shown
    84193145.gif



prev.gif next.gif

Oct 07, 2010 | 1998 Saturn SL

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


To Install:
  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark a0080774.gif

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Oct 07, 2010 | Ford F-250 Cars & Trucks

1 Answer

I need a timing chain diagram for a 2002 jeep grand Cherokee with a 4.0L engine


This is the procedure on it.


spacer.gif 2008-10-22_161446_1.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif

INSTALLATION

NOTE: Assemble the timing chain, crankshaft sprocket and camshaft sprocket with the timing marks aligned Fig. 5 .
  1. Apply Mopar(TM) Silicone Rubber Adhesive Sealant to the keyway in the crankshaft and insert the key With the key in the keyway on the crankshaft, install the assembly on the crankshaft and camshaft.


spacer.gif 2008-10-22_161528_2.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif

Install the camshaft sprocket retaining preload bolt and washer Fig. 6 . Tighten the preload bolt to 108 N.m (80 ft. lbs.) torque.





spacer.gif 2008-10-22_161605_3.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif


  • To verify correct installation of the timing chain, turn the crankshaft to position the camshaft sprocket timing mark as shown in Fig. 7 . Count the number of chain pins between the timing marks of both sprockets. There must be 15 pins. NOTE: Installation of the timing chain with the timing marks on the crankshaft and camshaft sprockets properly aligned ensures correct valve timing. A worn or stretched timing chain will adversely affect valve timing. If the timing chain deflects more than 12.7 mm (1/2 inch) replace it. The correct timing chain has 48 pins. A chain with more than 48 pins will cause excessive slack.
  • Install the crankshaft oil slinger.
  • Replace the oil seal in the timing case cover.
  • Lubricate the tension spring, thrust pin and pin bore in the preload bolt with Mopar(TM) Engine Oil Supplement, or equivalent. Install the spring and thrust pin in the preload bolt head Fig. 6 .


    spacer.gif 2008-10-22_161701_4.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif


  • Install the timing case cover and gasket.
  • With the key installed in the crankshaft keyway, install the vibration damper, washer and bolt. Lubricate and tighten the bolt to 108 N.m (80 ft. lbs.) torque.
  • Install the serpentine drive belt and tighten to the specified tension, Refer to Engine/Drive Belts, Mounts, Brackets and Accessories/Drive Belt/Service and Repair for the proper procedure.
  • Install the fan and hub (or Temporal fan) assembly. Install the shroud.
  • Connect negative cable to battery
  • Jul 16, 2010 | Jeep Grand Cherokee Cars & Trucks

    2 Answers

    Need instructions to replace 1993 Toyota Camry Timing Belt


    Hi Kmcarroll77

    TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

    Installation
    1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

    CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
    4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
    CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
    9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
    b7619be.jpg
    92cabaf.jpg
    Hope this helps, don't forget to rate.

    Lazaruselite

    Feb 25, 2009 | 1993 Toyota Camry V6

    1 Answer

    Help


    I will assume you are referring to the timing procedure for a replacement timing belt (4 cyl) or timing chain (V6) With the V6 timing chain you simply line up the timing marks on the two sprockets so that they are pointing directly toward each other, crankshaft sprocket with the mark pointing straight up, camshaft mark straight down. With the 2.3 L 4 cylinder engine, you must first position the crankshaft at TDC, and then position the oil pump and camshaft sprockets with their timing marks to line up with their respective marks on the inner cover. Install the belt and release the spring tensioner to let it adjust itself, tighten the tensioner bolt, and turn the engine over for 2 rotations (always clockwise as viewed from the front, never backwards). Make sure the marks still line up, loosen the tensioner, allow it to retension itself, and tighten the tensioner bolt. If the oil pump sprocket is not timed correctly, the camshaft position sensor signal will be incorrectly timed.

    Aug 01, 2008 | 1997 Ford Ranger SuperCab

    Not finding what you are looking for?
    2002 Ford Escape Logo

    184 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76673 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    fordexpert

    Level 3 Expert

    5537 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...