Question about Cars & Trucks

1 Answer

<!-- from fixya rte -->How do I replace washer nozzles - Cars & Trucks

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

You didn't mention make and model, but most can be changed by removing underhood pad sqeezeing plasic retaining clips and popping out nozzles- some are screwed or bolted under hood, either way access under hood pad

Posted on Nov 15, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2002 town & country rear washer does not work

replace the washer pump theres one for front and one for rear

Feb 18, 2014 | 2002 Chrysler Town & Country

1 Answer

How do i replace wind sheild washer spray nozzles ?

make sure you have washer fluid come out of the pump when on,if so maybe clogged hose to nozzle or nozzle clogged up which you can clean chemical residues with a sharp needle then moderately blow air(with air hose) from nozzle towards end of hose that connects to pump. Hope this helps. Oh,make sure not to wiggle the nozzle because then it would change direction of spray.

Jan 01, 2014 | 1995 Chevrolet Tahoe

1 Answer

Windshield Washer nozzles

try removing the hose at the nozzles and use compressed air and a blower nozzle to blow back out the blockage from the nozzle opening

May 05, 2017 | 2001 Isuzu Rodeo

3 Answers

How do you fix low pressure on windshield washer fluid sprayer.

Its just plugged up, probably right at the nozzle it's a pretty tiny hole. To clear it out you need to find a small diameter wire that will fit inside the hole to clear the blockage. Something like a small gauge sewing needle or a straight pin. It can also get plugged up in the rubber tubing. Usually you can just blow through it with lung power. Just pull the tube off at the nozzle and run the washer this will tell you if it's the nozzle or the tubing.

Jan 22, 2011 | 1994 Honda Accord

1 Answer

Back in summer wiper washer stopped coming out of nozzles,replaced with new ones,still no pressure squirts about halfe inch from nozzles,iremoved hose from passenger side nozzle,no difference in...

pull minihose off near one nozzle and cycle the washer motor(if it's limpy pressure, blow compressed air down the hose. If possible blow compressed air (via its tube) into the nozzle from the top. Do the same for the other nzzle. You can determine from these steps if your problem is with the pump or not.

Dec 22, 2010 | 2006 Pontiac G6

3 Answers

I think my van has a clogged windshield nozzle. The wiper fluid comes out but doesn't even squirt high enough to hit the windshield.

First try to clean out the squirter nozzles.Take a very small wire, sometimes a staple works great, and stick it into the nozzle to clear any debris.Then try to spray it again.If this didn't solve the problem and the debris is cleared, then you either have a weak or blocked pump, which is located on the washer reservoir itself.Hope I could help!!! Rate me accordingly!! Thanks!

Oct 06, 2010 | 2002 Chrysler Town & Country

1 Answer

The resovir appear to be full however i am not ablew hen pulling the handle to get the washer fluid to come out i hear the motor working but noting comes out

Often the washer nozzles can get clogged. If you hear the washer pump running, you need to disconncect the small hose from the washer nozzle, and see if you get fluid pumped thru it when you hit your washer switch. If so, you need to unclog or replace the nozzle, and if no fluid is pumped out the hose, you need to remove and inspect the washer pump, as it might be dirty, or failed.

Feb 10, 2010 | 2006 Pontiac Torrent

2 Answers

Windshield washer will not work on my 2005 Dodge Durango

First thing to do is make sure it is full of washer fluid. I know, who would not check that? You would be surprised. Ok, now we know it is full so why is it not working? Did you check the fuse. Normally you can hear it try to work by having the hood open while you stand there and have someone try it. It is full and fuse is good and it is trying to pump then either the pump is working but not really pumping anything or what I suspect is more likely is that the spray nozzles are clogged with wax. This is very common and I have seen it time and time again. Remove one of the rubber hoses from a spray nozzle and see if it it pumping out fluid. If it is not, then the pump is bad and must be replaced. It it is pumping fluid then the nozzles are clogged. Use a fine needle to clean out the nozzles. You may have to take the nozzle off in order to clean it throughly. More than likely once you probe inside the nozzles with the needle they will start working. If you end up having to remove the nozzles, and they are metal, which they normally are, you can place them in a pan of boiling water. This will for sure clean them out. The hot water will soften the wax and make it easy to pick and blow out. Have a great 2010, and good luck getting your washer fixed.

Jan 10, 2010 | 2005 Dodge Durango

1 Answer

Replace window washer nozzels

Open the hood disconnect the hoses from nozzles and gently push the clips that hold the nozzles on off of the nozzles, push the nozzles through the hood. reverse the process for installation

Aug 11, 2009 | 2002 Chrysler Concorde

1 Answer

Washer fluid not coming out of nozzles

Before you replace the nozzle, take a sewing needle and clear any dirt in the nozzle bearing, that is where the water come out of the nozzle. Then reset the nozzle bearing. If that fails to work, then source a new nozzle for your vehicle.

Jan 19, 2009 | 2002 Saturn L-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides