Question about 2001 Mitsubishi Eclipse GT

1 Answer

I replaced the new flywheel and new clutch kits. It doesn't work. Why? If car is off I can shift in to a gear but it starts I cannot engage into gear. What is wrong?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 56 Answers

I don't suppose to know Mitsubishi cars at all but it sounds like a safety interlock related to the clutch pedal mechanism hasn't been reconnected correctly or may have been adjusted out of tolerance during the remove and replace process.

Posted on Nov 15, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have put a new clutch plate,pressure plate and release bearing on peugeot 206 but the gears are not going in when I start the car


Try starting it in gear than shift with rpm dwn shift Rev rpm up by 1500 to up shif let rpm go down by 1500

Oct 28, 2016 | Peugeot Cars & Trucks

2 Answers

My clutch on my 1985 Toyota truck has these problems the gears are hard to engage when truck warms up and now when I Release the clutch it moves less then a half an inch and the truck wants to take off can...


I suspect your clutch and pressure plate needs to be replaced,when you depress your pedal to disengage your transmission from your flywheel the pressure plate is not engaging enough to seperate the two it still has a little contact on your flywheel so it is going to be difficult to change gears and your relief is going to be shorter.If you change it out always remember buy a clutch kit with a clutch plate and pressure plate and pilot bushing and slave cylinder all in one kit.Always remove your flywheel and get it resurfaced that is a must ,the flywheels surface will become uneven over time and minimize your surface area on your disc,by getting it resurfaced it will assure your disc has 100% of the flywheel surface for hook up and when you depress your clutch it will clear your flywheel good luck

Jan 15, 2014 | Cars & Trucks

1 Answer

CLUTCH ON CITROEN C2 KEEPS DROPPING TO FLOOR AND WHINING SOUND WHEN MOTOR IS RUNNING


It jump because the clutch disc itself is good, but the clutch is not engaging-the pedal is not making the clutch engage. When it does, then you can shift without grinding, then you can shift period. Clutch pedal operates a cable or it operates a hydraulic system-they both, which ever one you have, move the clutch fork on the transmission bell housing just a bit to cause the clutch to disengage the transmission from the engine's flywheel...so you can shift, see, easy, smooth shifts, no problem, no grinding. Your clutch itself is okay, the pedal is just not operating it.

Dec 26, 2013 | Cars & Trucks

1 Answer

92 Toyota Pick up clutch doesnt enagage after replacing clutch, and flywheel?


are you sure the driven plate is on the correct side? The clutch bearing is correct on high? Does the slave or master cylinder works ok? do they keep steady pressure when needed? Is the clutch kit the correct part according to engine type?

Nov 12, 2012 | Cars & Trucks

1 Answer

1987 saab 9000 turbo transmission


bad pressure plate or stuck throw out bearing.

Jun 06, 2012 | Saab 9000 Cars & Trucks

1 Answer

I have a 1995 Chevy S10 4.6L 2WD Ext Cab truck. Just replaced the transmission and have bled the system. I started the engine and I cannot shift into first gear without grinding the gears. Any suggestions...


If you can see the slave cylinder actuate, then have someone push the clutch down and watch for movement. You should see the release lever move at least a half inch. Let me know if you get movement. I also would like to know if you had the flywheel machined and if you removed, replaced, or added any shims between the ****** and engine block.

Oct 06, 2011 | 1995 Chevrolet S-10 CA Edition

1 Answer

HARD TO SHIFT INTO GEAR. IF I SHIFT INTO FIRST BEFORE I START THE TRUCK IT WILL SHIFT EASILY IF STARTED IT HARD TO SHIFT.


hi it sounds like your clutch is on its way out thats why when the engine switch off its easy for the gear to go in but when the engine is running the flywheel is turning and makes if very difficult or sometimes impossible to engage the gear as the clutch is worn and wont disengage .

Sep 02, 2010 | 1996 Mazda Pickup

Not finding what you are looking for?
2001 Mitsubishi Eclipse GT Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...