Question about 2003 Chevrolet Tracker
How do I remove the front bumper fascia on a 2003 Chevrolet Tracker?
Best way is ask a garage that does Chevy or get an illustrated parts list, maybe online or ebay and this will at least show the location of all the bolts and clips for the front end. One thing is, have you a comprehensive tool kit to tackle this task and maybe a degree of knowledge to identify the components?
Posted on Nov 15, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
There are two black plastic clips behind the the air filter, remove them and release the whole assembly to access the lights.
If you still get in troubles, have it replaced at a petrol station, they will help you in fitting the bulb, and it won't be expensive.
2003 Chevrolet Tracker Light Bulb Size Chart
Low Beam Headlight Bulb Size: 9003/HB2
High Beam Headlamp Light Bulb Size: 9003/HB2
Parking Light Bulb Size: 1157A
Front Turn Signal Light Bulb Size: 1157A
Rear Turn Signal Light Bulb Size: 921
Tail Light Bulb Size: 7443
Stop Light Bulb Size: 7443
High Mount Stop Light Bulb Size: 168 Or 921
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 921
Front Sidemarker Light Bulb Size: 194
Ash Tray Light Bulb Size: 74
Step/Courtesy Light Bulb Size: 168
Trunk/Cargo Area Light Bulb Size: 168
Instrument-General Light Bulb Size: 158 or 74
Check Engine Indicator Light Bulb Size: 74
Hi-Beam Indicator Light Bulb Size: 74
Seat Belt Indicator Light Bulb Size: 74
Brake Warning Light Bulb Size: 74
Automatic Transmission Indicator Light Bulb Size: 74
Directional Signal Indicator Light Bulb Size: 74
Posted on Oct 02, 2008
You have an heated Oxygen sensor. 2 of the wires heat up the sensor and keep it at a certain temperature, it is turned on and off by the computer. The other 2 are use to send a very low voltage reading back to the computer to tell the computer if the engine is running rich or lean. I don't have a diagram to tell you which wire does what but you can get a manual and that should give you the information that you need and tell you how to trouble shoot it to tell if the sensor is bad or not, you may want to look for a wire laying on the exhaust, I have found wires burnt and lay on the metal.
Posted on Oct 31, 2008
I don't know if your vehicle is a 4 cylinder or 6 cylinder. This will make a difference in the # of cylinders as well as the placement. If it is the 4 c ylinder when you open the hood it says at Autozone.com that the spark plugs are on the front of the motor lined up 1-4. If it is the 6 cylinder then you will have 3 at the front of the motor and 3 at the back of the motor. Regardless it is the same concept. I don't know for this particular vehicle, but it is possible you may have to remove a large plastic engine covering in order to access the spark plugs. What I recommend is to replace the spark plug wires at the same time as the plugs. For all my vehicles I use NGK plugs and NAPA auto parts has the best plug wires I have used - Belden Maxx. Prior to starting you will want to check the "GAP" on each new spark plug. Using a spark plug gap tool available at parts places for about $1. Take the new plug and the non-porcelin end (the end that has the arc) insert the arc into the gap tool at the lowest end and slide the plug around until you reach the corresponding "GAP". For this vehicle it should be .44" (I checked on Autozone's website but you may want to check to be sure. At some of the part's places they may tell you that you don't have to check the gap, but believe me you alway's should. I just did a car where they insisted that I didn't need to check the gap and each plug was not gapped properly. The Arc on the plug has to be specific for your vehicle or you will have too much spark or not enough. After gapping the new plugs you are ready to start. Somewhere on the side of the motor you should see either 4 or 6 wires/cables branching out to the cylinders. Starting with whichever you prefer (do only one at a time to avoid confusion) trace the wire/cable to the cylinder and where it goes to the cylinder a "boot" covers the spark plug. Twist the boot until it comes off . If you are going to replace the plug wires take that one off and match it up to your new set (They will be different lengths). You will need a ratchet and a spark plug socket (available at parts places) The spark plug socket has rubber on the inside to protect the porcelin of the spark plug, and to provide grip. You may or may not need a small extension. Place the spark plug socket over the end of the spark plug and apply pressure until the spark plug begins to loosen. You may have to apply quite a bit of pressure if they are in there tight. Once it is loosened take the old plug out, and place the new plug in the spark plug socket. Don't use the ratchet at this point, just begin to thread the plug in by hand once it is in there as much as you can get it, tighten it down with the ratchet making sure not to over-tighten. Do the other cylinders in the same manner.
Posted on Mar 04, 2009
SOURCE: chevy tracker 4 cyl 4wd 2003
Most major auto part chain stores have a loaner code scanner (they require you to leave your ID while you use the tool in their parking lot). There is a connector under the dash near on the drivers side that accepts the reader....check the codes and Google them for repair info or post them back here.
Posted on Jun 10, 2009
Tips for a great answer:
Oct 29, 2011 | 2002 Chevrolet Tracker
To replace a headlamp bulb, do the following:
1. Open the hood.
2. Remove the rubber
cover and socket from
3. Release the retainer clip holding the bulb by
pressing down and moving the metal retainer away
4. Pull the bulb out of the fixture.
5. Reverse the steps to install a new bulb.
You can get a free owners manual at this site (where i got your info)
It's free just enter the code they give you and Save or Open it. I'd save it. The site is safe.
Mar 10, 2011 | 2003 Chevrolet Tracker
Remove the bolts from the front bumper fascia at the fender
Remove the 3 bolts which secure the composite headlamp
Oct 12, 2010 | 2003 Pontiac Vibe
Oct 27, 2009 | 2008 Chevrolet Malibu
Jun 13, 2009 | 2003 Cadillac CTS
159 people viewed this question
Usually answered in minutes!