Question about Cars & Trucks

1 Answer

Okay so I have finally accepted the fact that I'm bi. My mom is a big homophob and I'm afraid to tell her. My step brother told her he was bi and she didn't like it and he asked what if one of us was bi and she said we would have problems. I really like this girl like a lot and I'm not sure how to tell my mom. How should I tell her because I can't stop thinking about it.

Posted by on

1 Answer

I wouldn't tell her

Let her figure it out, a year from now

The end result is the same

She doesn't want to know, so leave it that way

Better Bi than then switched

Posted on Nov 15, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

I have a 2002 4WD Blazer. I just replaced tthe head gaskets and now have a bad coolant lea, Fuel leak, and it wont turn over


Unfortunately it sounds like the head gasket/s were not torqued down correctly with new stretch bolts. Sorry but it requires stripping down again and sorting out.

Mar 19, 2014 | 1998 Chevrolet Blazer

1 Answer

1993 Ford Escort 4-door: Back-up and license plate lights are out. All fuses checked = okay. All bulbs ohmed out/visual = okay. All other lights are functioning properly (parking, brake, turn, headlight,...


the back-up lights would probably be a bad reverse switch at that point. I'm not sure what could be causing the plate lights if its not fuses or bulbs and all the others are working. I would highly recommend checking your bulbs one more time and look to see if the filaments are smooth or pitted. if they are pitted but otherwise appear to be ok they are in fact burnt out. I have even seen bulbs n that condition ohm out ok but still not work.

Oct 03, 2009 | 1994 Ford Escort

2 Answers

I have a 1990 delta 88 and the engine light is on and i have a part to have the light blink to tell me whats wrong but dont kno the code how can i kno


the part is a paperclip. Inserted in A & B sockets of the diagnostic connector. You must then count the flashes. long flashes 1st, followed by short flashes. the longs indicate 10, the shorts are 1. so 2 longs and 3 shorts would be a code 23, 4 longs and 2 shorts would be a 42...etc etc. after the shorts finish, there will be a semi-long pause, then it will start flashing longs and shorts again. watch and count flasghes AGAIN carefully. if its the same as before, that is your only code. It MAY be a different number, meaning you have more than 1 code. count them long/short sequences 1 after another and write them down till you have them all saved. Then search them on the internet or repost them and if I happen to see it, I may be able to lead you further.

This work is usually done with expensive tools for a reason. flash codes are a basic and limited diag step...replacing parts based on what they tell you can waste hundreds of dollars if its not an obvious problem, so be careful before buying parts just because you get a code for o2 sensor rich or MAP sensor voltage high. Its not always the part mentioned in the code, that may in fact simply be the sensor alerting you it sees a mechanical problem and the sensor is in fact accurate. The car may BE rich, or there may BE a big vacuum leak...etc etc. If you arent comfortable with the troubleshooting, dont be afraid to take it to a professional.

Sep 15, 2009 | 1991 Oldsmobile 88

1 Answer

Alarm trouble


There is no switch to turn it off. when the alarm is in alarm mode you have to lock all doors, then use key to unlock drivers door or rear hatch. This will turn alarm off

Nov 24, 2008 | 1997 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...