Question about 2008 Dodge Magnum

1 Answer

I can't open the hood on my 2008 dodge magnum. I pull the lever and you can hear it pop but hood doesn't pop up what should I do

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Pop the hood then go too front of car and hit hood near front with your palm. Try two or three different locations

Posted on Nov 14, 2014

  • Cortney Jackson
    Cortney Jackson Nov 14, 2014

    It was unlatching it just wasn't popping up like it w as supposed to. I pried it up with a screw driver then had to open and close a few times but it works now.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The hood on my 2008 dodge magnum won't open I pull the lever and you can hear it pop but hood doesn't pop up like it's supposed to. Any ideas on how to get it open


Use a plastic putty knife and pry it up. pry between the hood and front near the center of the car. good luck then lube it with white grease

Nov 14, 2014 | 2008 Dodge Magnum

2 Answers

Honda civic hood latch


The metal loop on the hood is probably misaligned from the latch at the bottom. The loop should have a couple of bolts to loosen and adjust.

Oct 21, 2013 | Cars & Trucks

1 Answer

2008 Mitsubishi release cable for Hood not working. When pulling on release inside car, the hood does not pop open to reach under and release the safety latch


I have a similar problem on my 2006 VW Passat.

I'm able to open the hood two ways:
1) ask someone to hold onto the lever inside the car while you try to lift the hood to the point where you can use the unlatch button and open the hood fully.


2) Pull the lever completely open in the car and try to find a thick screwdriver or some thick paper folded up to wedge next to the lever to hold it open while you get out and try to lift the hood to the point where you can use the unlatch button and open the hood completely.


Other than this finding a service manual or tutorial online about how to pull out whatever trim or interior covers you would need to replace the cable fully. There should be a specific replacement guide for this item since I'm sure it happens to car's at least semi-regularly

Aug 31, 2013 | Mitsubishi Galant Cars & Trucks

1 Answer

We heve a 2000 chevy Tahoe and can't get the hood open. We hear it pop but it doesn't open enough to put your hand in.


Have some one pull the handle and some one smack the hood where the latch is, or pull up on the hood with the handle pulled.

Jun 18, 2011 | Chevrolet Tahoe Cars & Trucks

2 Answers

How do I open the hood of a Mitsubishi L300 ?


  1. Locate the interior hood-release lever under the dashboard on the driver's side of the interior of the car.

  2. 2

    Lift up and toward you on the hood release lever. The lever is connected to a cable that releases the hood. The hood will pop up about 1/2 inch when you pull the lever.

  3. 3

    Move to the front of the car and locate the exterior hood-release lever under the front of the hood. It is located near the middle of the vehicle, just beyond where the front edge of the hood meets the body. Lift up on the inner lever.

  4. 4

    Lift up on the edge of the hood while holding the inner lever in place. When the hood is up, find the hood prop and raise it, setting its tip in the hood-prop mount on the hood, to hold the hood up while you work in the engine bay.



Read more: How to Open the Hood on a Mitsubishi Endeavor ' eHow.com http://www.ehow.com/how_6301122_open-hood-mitsubishi-endeavor.html#ixzz16Ou5FhQF

Nov 26, 2010 | Mitsubishi Lancer Cars & Trucks

2 Answers

My hood is stuck and won't pop


While you are pulling out on cable have someone hit hood with each fist on front of hood near grill left & right of center at same time.

Jun 28, 2010 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Clicking Lifter noise 06 Dodge Magnum (2.7l v6 DOHC 24-valve)


get a tool called a stefascope,what doctors wear.its good for hearing noises

Sep 20, 2009 | 2006 Dodge Magnum

1 Answer

2008 magnum, has been in an accident and the seat belts are locked


Not 100% sure but a lot of dodge products have electric seatbelts that won't pull out without battery voltage. Check the underhood fuse box of a fuse marked seatbelts to see if it blown. Check your owners manual in the seatbelt section.

May 03, 2009 | 2008 Dodge Magnum

1 Answer

Hood will not release


pull the lever and with your hand pull up on the hood. You may need somebody to hold the lever inside the car while somebody pulls up on the hood. The spring mechanism may be faulty.

Dec 07, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...