Question about Cars & Trucks

1 Answer

Which way around should the crank pick up reluter ring be fitted B on the outside or inside 2006 Toyota corolla 1400cc

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

The ring should have come with the new part. If it isn't there, then you got the wrong part. If it was there and was different, you still got the wrong part. send it back and get the right one.

Posted on Nov 16, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Alt 100 fuse what is its purpous 2006 toyota corolla

I think that is the main fuse for the alternator, which when blown prevents battery charging.

Mar 08, 2015 | 2006 Toyota Corolla

2 Answers

Engine cranks but no start, no spark. What else can I check?

is it actually rotating when the engine turns over I know sounds stupid but I\'ve seen the teeth that goes inside against the cam break off on first turn over happened to me once on a Honda, also that same car my original problem was I was getting power and everything like you but the icm on the distributor was putting the power out on the ground side and the power turned to ground not allowing the distributor to do its job and produce spark

hope this helps

Aug 29, 2014 | 1994 Toyota Corolla

1 Answer

How to replace 2006 trailblazer tranmission lines

there are spring clips on the fittings that you can easily remove with a seal pick slide the old line out replace the clip and o-ring inside of fitting and push the new line in till it clicks

Aug 29, 2014 | 2006 Chevrolet Trailblazer

1 Answer

There is a part inside the dome light that is broken and not making contact. It is not where the bulb goes. I can push on the switch on the outside and the light will come on. So it is working, I just...

If you call your local Toyota Dealer , they can bring up the picture of the area you are referring to, most of the time you give them the VIN of the vehicle and they can pull up all that information for you.

Good Luck.

Aug 25, 2010 | 2006 Toyota Corolla

1 Answer


you might need a new computer

Feb 08, 2010 | 2006 Toyota Corolla

1 Answer

How do I remove the cigarette lighter socket in the console, 2006 Toyota corolla S ?

hi to remove the lighter ease of the crome retaining ring around the lighters edge you may have to use a flat ended screwdriver one off you lighterand connection will come out

Nov 18, 2009 | 2006 Toyota Camry

1 Answer

Replaciing serpentine belt on 2006 Toyota Corolla

You'll have to remove the engine cover under the bottom so you can position the new belt on the pulleys properly. Get a wrench or tensioner tool and turn the tensioner clockwise to relax the drive belt. Don't apply excessive force.

It's hard to draw a picture with words, but looking at the engine from the passenger side of the car, there are basically two top pulleys, two middle, and two bottom. The drive belt goes around the outside of the two top and two bottom, and on the inside of the two middle.

Oct 31, 2009 | 2006 Toyota Corolla

1 Answer

How do i remove the brake rotor from a 2003 toyota corolla? it seems that there is a special nut holding it on. i have looked for a socket but nothing seem to fit. Please help!!!!!

Have you removed the locking pin around the nut? There should be a metal ring with a dent notched into the nut you need to take out that notch in order to remove the nut.

Jul 07, 2009 | 2003 Toyota Corolla

1 Answer

Headlight bulb is out on...I need to replace it.

Put on your marigold gloves, pull off the 3 terminal plug behind the bulb.
Undo the retaining ring.
Pull out the bulb, memorizing its position, check its the same as your new one, and don´t touch glass on new bulb, as any grease on it will do it no good.
Pop it in and fit the securing ring and refit the plug.
Now test it for dip and main beam.
See it was easy !
Good Luck !

Jan 13, 2009 | 2006 Toyota Corolla

1 Answer

Broken O ring on fuel ports

Check with dealer incase part not available separately. Might have to purchase whole assembly or obtain from wrecker.

Oct 04, 2008 | 2006 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides